Spirit XE320 User manual

SPT0040 – XE320
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
OWNER’S MANUAL

XE320 Elliptical
1
Product Registration…………………………………………………………………………. .2
Important Safety Instructions…………………………………………………………………3
Important Electrical Information………………………………………………………………4
Important Operation Instructions……………………………………………………………..4
Assembly Instructions………………………………………………………………………….5
Features………………………………………………………………………………………..11
Operation of Your New Elliptical……………………………………………………………..12
Parts list and Explode Drawing………………………………………………………………21
Manufacturer’s Limited Warranty…………………………………………………………….25
Table of Contents

XE320 Elliptical
2
Thank you for your purchase of this quality elliptical trainer. Your new elliptical was
manufactured by one of the leading fitness manufacturers in the world and is backed by
one of the most comprehensive warranties available.
Please take a moment at this time to record the name of the dealer and the date of
purchase below to make any future, needed contact easy. We appreciate your support
and we will always remember that you are the reason that we are in business.
Yours in Health,
BOYLES FITNESS Equipment Pty Ltd.
Name of Dealer______________________________________
Purchase Date_______________________________________
XE320/ SPT0040 _Ver.A
CONGRATULATIONS ON YOUR
NEW ELLIPTICAL AND WELCOME
TO THE SPIRIT FAMILY!

XE320 Elliptical
3
WARNING - Read all instructions before using this appliance.
■Do not operate the elliptical on deeply padded, plush or shag carpet. Damage to both the
carpet and elliptical may result. Set the elliptical up on a hard, even surface.
■Keep children away from the elliptical . There are obvious pinch points and other
caution areas that can cause harm.
■Keep hands away from all moving parts.
■Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working
properly, call your dealer.
■Keep the cord away from heated surfaces.
■Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
■Never drop or insert any object into any openings.
■Do not use outdoors.
■To disconnect, turn all controls to the off position, then remove the plug from the outlet.
■Do not attempt to use your elliptical for any purpose other than for the purpose it is
intended.
■The hand pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
■Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your elliptical . Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Safety Instructions

XE320 Elliptical
4
WARNING!
● NEVER remove any cover without first disconnecting AC power supply.
● If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may be
affected. Such conditions are not covered under your warranty. If you suspect the
voltage is low, contact your local power company or a licensed electrician for proper testing.
● NEVER expose this elliptical to rain or moisture. This product is NOT designed for
Use outdoors, near a pool or spa, or in any other high humidity environment.
● NEVER operate this elliptical without reading and completely understanding the results of
any operational change you request from the computer.
● Understand that changes in resistance do not occur immediately. Set your desired level on
the computer console and release the adjustment key. The computer will obey the
command gradually.
● NEVER use your elliptical during an electrical storm. Surges may occur in your household
power supply that could damage elliptical components.
● Use caution while participating in other activities while using your elliptical such as watching
television, reading, etc. These distractions may cause you to lose balance, which may result
in serious injury.
● Always hold on to a handrail or hand bar while making control changes.
Do not use excessive pressure on console control keys. They are precision set to properly
function with little finger pressure. Pushing harder is not going to make the unit go faster or
slower. If you feel the buttons are not functioning properly with normal pressure, contact your
Spirit dealer.
Important Electrical Information
Important Operation Instructions

XE320 Elliptical
5
Assembly Instructions
ASSEMBLY PACK CHECK LIST
Step 1
#66. M5 x 10m/m
Phillips Head Screw (4pcs)
#103. 3/8" x 3/4"
Hex Head Bolt (2pcs) #60. 3/8" x 2-1/4"
Hex Head Bolt (1pcs)
#96. 3/8" x 2T
Split Washer (1pcs)
Step 2
#79. 5/16"x23x1.5T
Flat Washer (2pcs)
#59. 5/16"x 15 m/m
Hex Head Bolt (2 pcs)
#83. 17 m/m
Wave Washer (2 pcs)
#84. 3/8" x 23 x 1.5T
Curved Washer (2pcs)
#104. 5/16” x 1-1/4”
Hex Head Bolt (2 pcs)
#80. 5/16" x 20x 1.5T
Flat Washer (2 pcs)
#71. 5/16" x 7T
Nyloc Nut (2 pcs)
Step 3

XE320 Elliptical
6
ASSEMBLY PACK CHECK LIST
Step 4
Tools
#87. Ø3.5x12m/m
Sheet Metal Screw (8pcs)
#105.M5 x 15m/m
Phillips Head Screw (14pcs)
#108. Phillips Head Screw Driver (1pcs)
#107. Short Phillips Head Screw Driver (1pcs)
#109. 12m/m Wrench (1pcs)
#106. 13/14m/m Wrench (1pcs)

XE320 Elliptical
7
STEP 1: CONSOLE MAST ASSEMBLY
1. Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the Mast as far as
it will go. Make sure the Console Mast Cover (41) is facing the correct way.
2. At the top opening of the Main Frame (1), there is a Computer Cable (31) tied with a guiding wire.
Unravel the wire and feed the Computer Cable (31) it into the bottom of the Console Mast (12) and out
of the top opening.
3. Install the Console Mast (12) into the receiving bracket on the top of the Main Frame (1).
NOTE: there is one bolt already installed in the receiving bracket that will engage with the slot at the
bottom of the Console Mast. This needs to be tightened at the end along with the three other console
mast bolts.
4. Put the 1pc of 3/8" x 2T Split Washer (96) onto the 1pc of 3/8" x 2-1/4" Hex Head Bolt (60) and the 2pcs
of 3/8” x 23 x 1.5T Curved Washers (84) onto the 2pcs of 3/8" x 3/4" Hex Head Bolts (103). Install, and
hand tighten them. The Hex Head Bolt (60) should go through the left side of the receiving bracket into
the Console Mast (12).
NOTE: The Computer Cable (31) runs through the Console Mast (12). Be careful not to damage or
pinch this cable during this procedure. Be careful as damage to the Console Assembly (30) could result.
Install, and hand tighten the 2pc of 3/8" x 3/4" Hex Head Bolts (103) with 3/8” x 23 x 1.5T Curved
Washers (84) through the front of the receiving bracket into the Console Mast (12).
5. Using the 13/14m/m Wrench (106) to tighten the three bolts, and the fourth screw, which is pre-installed,
firmly. These bolts should be tightened as much as you possibly can.
6. Locate the Console Assembly (30) and tighten it with the 4pcs of M5×10 m/m Phillips Head Screws (66)
by using the Phillips Head Screw Driver (108).
7. There are three connectors at the top opening of the Console Mast (12), two Handpulse W/Cable
Assemblies (36), and one Computer Cable (31). Connect these to the mating connectors on the back of
the Console Assembly (30). Do not force them while connecting as the connectors are keyed so that
you cannot plug them in the wrong way.
8. Store the excessive cables back into the Console Mast (12) and carefully install the Console Assembly
(30) onto the mounting plate of Console Mast (12) and secure the 4pcs of M5 x 10m/m Phillips Head
Screws (66) by using Philips head screw driver (108).

XE320 Elliptical
8

XE320 Elliptical
9
STEP 2: HANDLE BAR ASSEMBLY
1. Install the 4pcs of Ø 17 Wave Washers (83) onto the Left and Right side of the Console Mast axle.
2. Slide the Swing Arms (L) and (R), (10&11) onto the appropriate side of the axle.
3. Put the 2pcs of 5/16" × 15m/m Hex Head Bolts (59) onto the 2pcs of 5/16" × 23 × 1.5T Flat Washers
(79) and install, tighten by using 12m/m Wrench (109), in the threaded holes in the ends of the axle.