SportDOG houndhunter 3225 User manual

2 1-800-732-0144 WWW.SPORTDOG.COM 3
Important Safety InformatIon
Explanation of Attention Words and Symbols used in this guide
____________________________________________________________________
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible injury or death.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION
CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if
not avoided, could result in harm to your dog.
WARNING
• Not for use with aggressive dogs. Do not use this product if your dog is aggressive, or if your dog is
prone to aggressive behavior. Aggressive dogs can cause severe injury and even death to their owner
and others. If you are unsure whether this product is appropriate for your dog, please consult your
veterinarian or a certified trainer.
• This device contains Lithium-Ion (Li-Ion) batteries; never incinerate, puncture, deform, short-circuit, or charge
with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this warning is not
followed.
• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
CAUTION
Please read and follow the instructions in this manual. Proper fit of the collar is important.
A collar worn for too long, or made too tight on the dog’s neck may cause skin damage. This is called bed
sores; it is also called decubitus ulcers or pressure necrosis.
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
For additional information on bed sores and pressure necrosis, please visit the FAQ section for remote
trainers at www.sportdog.com.
These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable while they
wear stainless steel contacts. Some dogs are sensitive to contact pressure. You may find after some time
that your dog is very tolerant of the collar. If so, you may relax some of these precautions. It is important
to continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin
has fully healed.
• You may need to trim the hair in the area of the Contact Points or switch to the longer contact points to ensure
consistent contact. Never shave the dog’s neck; this may lead to a rash or infection.
• You should not make the collar any more tight than is required for good contact. A collar that is too tight will
increase the risk of pressure necrosis in the contact area.
400-1226.indd 2-3 6/11/10 4:27 PM

4 1-800-732-0144 WWW.SPORTDOG.COM 5
Thank you for choosing SportDOG Brand.® Used properly, this product will help you train your dog
efficiently and safely. To ensure your satisfaction, please review this owner’s manual thoroughly. If you
have questions regarding this product’s operation, please see this manual’s Frequently Asked Questions
or Troubleshooting section, contact our Customer Care Center at 1-800-732-0144, or visit our website at
www.sportdog.com.
To get the most protection out of your warranty, please register your product within 30 days at
www.sportdog.com. By registering, and keeping your receipt you will enjoy the product’s full warranty
and should you ever need to call the Customer Care Center, we will be able to help you faster. Most
importantly, SportDOG™ will never give or sell your valuable information to anyone. Complete warranty
information is available online at www.sportdog.com.
____________________________________________________________________
taBLe of ContentS
COMPONENTS .............................................................................................................................................................5
HOW THE SYSTEM WORKS .......................................................................................................................................5
KEY DEFINITIONS ........................................................................................................................................................6
PREPARE THE REMOTE TRANSMITTER .................................................................................................................7
PREPARE THE COLLAR RECEIVER............................................................................................................................8
FIT THE COLLAR RECEIVER .....................................................................................................................................10
FIND THE BEST INTENSITY LEVEL FOR YOUR DOG ...........................................................................................11
CHANGING STIMULATION RANGES .................................................................................................................... 11
GENERAL TRAINING TIPS .......................................................................................................................................12
PROGRAM THE REMOTE TRANSMITTER ............................................................................................................12
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER.....................................................................14
PROGRAM THE SYSTEM FOR TWO-DOG OPERATION .....................................................................................15
PROGRAM THE SYSTEM FOR THREE - SIX-DOG OPERATION.........................................................................15
ACCESSORIES ............................................................................................................................................................16
FREQUENTLY ASKED QUESTIONS .........................................................................................................................17
TROUBLESHOOTING .................................................................................................................................................18
TEST LIGHT INSTRUCTIONS ...................................................................................................................................19
TERMS OF USE AND LIMITATION OF LIABILITY ................................................................................................19
FCC COMPLIANCE .....................................................................................................................................................20
CUSTOMER CARE INTERNATIONAL .....................................................................................................................20
BATTERY DISPOSAL .................................................................................................................................................21
SPORTDOG™ ADD-A-DOG® RECEIVERS ...............................................................................................................24
ComponentS
HoW tHe SyStem WorKS
The SportDOG™ HOUNDHUNTER® 3225 has been proven safe, comfortable and effective for all dogs
over 8 pounds. Consistent, correct use of this product allows you to reinforce commands and correct
misbehavior from two miles. The Remote Transmitter sends a signal, activating the Collar Receiver
to deliver a harmless stimulation. With proper training, a dog will learn to associate this signal with a
command. Like all SportDOG products, this model features adjustable stimulation levels so you can tailor
the stimulation level to your dog’s temperament, eliminating the risk of over-correction.
IMPORTANT: THE HOUNDHUNTER 3225 HAS A RANGE OF TWO MILES.
DEPENDING ON THE WAY YOU HOLD THE REMOTE TRANSMITTER, THE
MAXIMUM RANGE MAY VARY. FOR CONSISTENT RESULTS AT LONGER
RANGES, HOLD THE REMOTE TRANSMITTER IN A VERTICAL POSITION AWAY
FROM YOUR BODY AND ABOVE YOUR HEAD. TERRAIN, WEATHER, VEGETATION,
TRANSMISSION FROM OTHER RADIO DEVICES, AND OTHER FACTORS WILL
AFFECT THE MAXIMUM RANGE.
WARNING
Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behaviour.
Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this
product is appropriate for your dog, please consult your veterinarian or a certified trainer.
400-1226.indd 4-5 6/11/10 4:27 PM

6 1-800-732-0144 WWW.SPORTDOG.COM 7
Key DefInItIonS
REMOTE TRANSMITTER: Transmits the radio signal
to the Collar Receiver. It is waterproof and can be
submerged in water to a depth of 25 feet.
INTENSITY DIAL: Provides multiple levels/types of
stimulation so you can match the correction to your
dog’s temperament.
TRANSMITTER INDICATOR LIGHT: Indicates that a
button is pressed and also serves as a low-battery
indicator.
TOGGLE SWITCH: This switch is factory-set so that the
Remote Transmitter can control two Collar Receivers.
UPPER BUTTON: This button is factory-set to deliver
continuous stimulation.
LOWER BUTTON: This button is factory-set to deliver
momentary stimulation, or a “Nick.”
SIDE BUTTON: This button is factory-set to deliver a
tone without stimulation.
CHARGING JACK: For connecting the charger. Although
the Remote Transmitter is waterproof without it, keep
the cover in place when not charging to keep debris out
of the opening.
COLLAR RECEIVER: Receives the radio signal from
the Remote Transmitter and delivers the stimulation,
vibration and/or a tone for correcting your dog. It is
waterproof and can be submerged in water to a depth of
25 feet.
RECEIVER INDICATOR LIGHT: Indicates when the Collar
Receiver has been turned on or off and also serves as a
low-battery indicator.
CONTACT POINTS: The contacts through which the
Collar Receiver delivers stimulation.
ON/OFF BUTTON: Momentarily pressing and releasing
this button turns the Collar Receiver on and off.
THE COLLAR RECEIVER IS CAPABLE OF DELIVERING FOUR TYPES OF STIMULATION VIA THE CONTACT POINTS:
CONTINUOUS: You control both when and how long stimulation is delivered, up to a maximum of 10
seconds. After 10 seconds, the stimulation will “time out” and the Transmitter button needs to be
released and then pressed again before additional stimulation can be delivered.
MOMENTARY (NICK): Stimulation is delivered for 1/10 of a second, regardless of how long the button is
pressed.
TONE: The Collar Receiver will make a rapid beeping noise when a Tone button is pressed.*
VIBRATION: The Collar Receiver will vibrate when a Vibration button is pressed.*
*Tone and vibration come preset and are not adjustable.
prepare tHe remote tranSmItter
CHARGE THE REMOTE TRANSMITTER
NOTE: Approximate battery life between charges is 40 to 60 hours, depending on frequency of
use. The Remote Transmitter is factory set to mode 1. If the dial is set to V/T, in this mode, and
any button is pressed, then no signal will be sent to the Collar Receiver. The mode of the Remote
Transmitter will need to be changed in order to utilize this feature (see Step 5).
tranSmItter InDICator LIGHt
OPERATIONAL MODE LIGHT COLOR BATTERY STATUS LIGHT FUNCTION
Continuous stimulation or
Tone only button pressed
Green Good Light is solid in color while
button is pressed
Continuous stimulation or
Tone only button pressed
Red Low Light is solid in color while
button is pressed
Momentary stimulation
button pressed
Green Good Light flashes once and
turns off
Momentary stimulation
button pressed
Red Low Light flashes once and
turns off
Unit is charging Red Low Light is solid in color while
on the charger
Unit is fully charged
(charger still connected)
Green Good Light flashes once per
second once the battery is
completely charged
REMOTE TRANSMITTER
COLLAR RECEIVER
CHARGER
CONNECTOR PLACED
IN THE REMOTE
TRANSMITTER
CHARGING JACK
1. Lift the rubber cover protecting
the Charging Jack.
2. Connect one of the charger
connectors to the Charging Jack.
3. Plug the charger into a standard
120-volt AC wall outlet.
4. Charge the Remote Transmitter for
2 hours for the first charge and
every charge thereafter.
Using Li-Ion technology, the
Remote Transmitter only requires
a 2 hour charge. It is not harmful
to let the unit charge for more than
2 hours.
5. When charging is complete,
replace the rubber cover.
STEP :: 01
TRANSMITTER
INDICATOR LIGHT
INTENSITY
DIAL
TRANSMITTER
ANTENNA
UPPER
BUTTON
LOWER
BUTTON
SIDE
BUTTON
CHARGING
JACK
TOGGLE
SWITCH
CONTACT POINTS
RECEIVER
INDICATOR
LIGHT
ON/OFF
BUTTON
400-1226.indd 6-7 6/11/10 4:27 PM

8 1-800-732-0144 WWW.SPORTDOG.COM 9
prepare tHe CoLLar reCeIVer
CHARGE THE COLLAR RECEIVER
CHARGE CRADLE INDICATOR LIGHT
TO TURN THE COLLAR RECEIVER ON:
TO TURN THE COLLAR RECEIVER OFF:
Press and release the On/Off Button when the Receiver Indicator Light comes on solid (red) and the
Collar Receiver beeps for 2 seconds.
To extend the life between charging cycles, turn the Collar Receiver off when it is not in use.
NOTE: Approximate battery life between charges is 40 to 60 hours, depending on frequency of use.
reCeIVer InDICator LIGHt
OPERATIONAL
MODE
LIGHT
COLOR
LIGHT FUNCTION BATTERY
STATUS
SPEAKER
FUNCTION
VIBRATION
Unit is turned on
via On/Off Button
Unit is turned on
via On/Off Button
Green
Red
Light is solid in color
during beep sequence
Light is solid in color
during beep sequence
Good
Low
Beeps 1-3 times
depending on
stimulation range
setting (2 is the
default setting).
Please see page 11.
N/A
Unit is turned off
via On/Off Button
Red Light is solid in color
during beep sequence
N/A Beeps for 2
seconds
N/A
Unit is on Green Light flashes every 2
seconds
Good N/A N/A
Unit is on Red Light flashes every 2
seconds
Low N/A N/A
Unit is delivering
continuous
stimulation
Red Light is solid in color
for as long as button is
pressed
N/A N/A N/A
Unit is delivering
momentary
stimulation
Red Light will quickly flash
once no matter how
long button is pressed
N/A N/A N/A
Unit is delivering
tone
Off N/A N/A Unit will beep for
as long as button is
pressed
N/A
Unit is delivering
vibration
Off N/A N/A N/A Unit will
vibrate for
as long as
button is
pressed
RECHARGEABLE BATTERIES
WARNING
• This device contains Lithium-Ion (Li-Ion) batteries; never incinerate, puncture, deform, short-
circuit, or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm
may occur if this warning is not followed.
• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS (page 21).
• The rechargeable Lithium Ion (Li-Ion) batteries are not memory sensitive, do not require
depletion before charging and cannot be over charged. Bateries should never be removed from
the battery compartment for charging.
• The batteries come partially charged from the factory, but will require a full charge before the
first use.
• When storing the unit for long periods, remember to regularly give batteries a full charge. This
should be done once every 3 to 4 months.
• You should expect hundreds of recharge cycles from your batteries. However, all rechargeable
batteries lose capacity over time relative to the number of recharge cycles they experience.
This is normal. If your operating time drops to half of the original life, contact the Customer Care
Center to purchase a new battery.
1. Place Collar Receiver in Charging
Cradle as shown.
2. Place the charger connector into the
back of the Charging Cradle.
3. Plug the charger into a standard 120-volt
AC wall outlet.
4. Charge the Collar Receiver for 2 hours
for the first charge and every
charge thereafter.
Using Li-Ion technology, the
Collar Receiver only requires
a 2 hour charge. It is not harmful
to let the unit charge for more than
2 hours.
Press and release the On/Off Button when the
Receiver Indicator Light comes on.
The Collar Receiver will beep 1 to 3 times
depending on what stimulation range is
chosen (page 11). The default is 2 or medium.
STEP :: 02
OPERATIONAL MODE LIGHT COLOR LIGHT FUNCTION
No Collar Receiver on the Charging
Cradle but charger is connected
Green Light is solid in color
Unit is charging Red Light is solid in color while charging
Unit is fully charged (Collar Receiver
on Charging Cradle)
Green Light flashes once per second once
the battery is completely charged
ON/OFF
BUTTON
400-1226.indd 8-9 6/11/10 4:27 PM

10 1-800-732-0144 WWW.SPORTDOG.COM 11
• The batteries should last for a period of 3-5 years. When a battery needs replacement, you can
order a new pack by calling our Customer Care Center at 1-800-732-0144. Please do not open the
Collar Receiver or Remote Transmitter until you have received the replacement.
• Do not charge the Collar Receiver in areas with high temperature (100° F+).
fIt tHe CoLLar reCeIVer
IMPORTANT: The proper fit and placement of the Collar Receiver is important for effective training.
The Contact Points must have direct contact with your dog’s skin.
CAUTION
Please read and follow the instructions in this manual. Proper fit of the collar is
important. A collar worn for too long, or made too tight on the dog’s neck may cause skin
damage. This is called bed sores; it is also called decubitus ulcers or pressure necrosis.
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
For additional information on bed sores and pressure necrosis, please visit the FAQ section for
remote trainers at www.sportdog.com.
These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable
while they wear stainless steel contacts. Some dogs are sensitive to contact pressure. You
may find after some time that your dog is very tolerant of the collar. If so, you may relax some
of these precautions. It is important to continue daily checks of the contact area. If redness or
sores are found, discontinue use until the skin has fully healed.
To ensure a proper fit, follow these steps:
1. With your dog standing (3A), center the Collar
Receiver so the Contact Points are underneath
your dog’s neck, touching the skin (3B). If your
dog has a long or thick coat, you have two
options to ensure consistent contact: either trim
3A
3B
the hair around the Contact Points or switch to the longer Contact Points included with your system.
CAUTION
• You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck;
this may lead to a rash or infection.
• You should not make the collar any more tight than is required for good contact. A collar that is too
tight will increase the risk of pressure necrosis in the contact area.
2. The Collar Receiver should fit snugly, yet loose enough to
allow one finger to fit between the strap and your dog’s
neck (3C).
3. Allow your dog to wear the collar for several minutes,
and then recheck the fit. Check the fit again as your dog
becomes more comfortable wearing the Collar Receiver.
3C
fInD tHe BeSt IntenSIty LeVeL for yoUr DoG
The HoundHunter® 3225 has multiple intensity levels. This allows you to choose the stimulation that is
best for your dog.
NOTE: Always start at the lowest level and work your way up.
For training efficiency, it is important to find the right intensity level for your dog. This is called the
Recognition Level, at which your dog looks around in curiosity, or flicks his ears.
FINDING YOUR DOG’S RECOGNITION LEVEL:
NOTE: Every dog is different and you cannot predict where your dog’s Recognition Level will be. Watch
closely for any slight change in behavior that tells you your dog is feeling the stimulation.
1. With the Collar Receiver turned on and properly fitted to your dog, set the Remote Transmitter’s
Intensity Dial at Level 1 and press the Continuous Stimulation Button for 1 to 2 seconds.
2. If your dog shows no reaction to Level 1, go to Level 2 and repeat the process.
3. YOUR DOG SHOULD NOT VOCALIZE OR PANIC WHEN RECEIVING STIMULATION. IF THIS
HAPPENS, THE STIMULATION LEVEL IS TOO HIGH AND YOU NEED TO GO BACK TO THE PREVIOUS
LEVEL AND REPEAT THE PROCESS.
4. Once you find your dog’s Recognition Level, this is the level you should use when you begin a
training exercise.
5. If you have progressed to Level 7 while searching for your dog’s Recognition Level and your dog
continues to show no response, check to see if Collar Receiver is snug against your dog’s neck.
Then go back to Intensity Level 1 and repeat the process. If your dog still does not indicate he is
feeling the stimulation, you have two options: you may either have to trim the hair beneath the
Contact Points or switch to the longer Contact Points included in your system.
If after completing all of these steps your dog still does not indicate he is feeling the stimulation, please
contact Customer Care Center at 1-800-732-0144.
CHanGInG StImULatIon ranGeS
The HoundHunter® 3225 Collar Receiver comes with 3 stimulation ranges (low, medium and high).
There are 7 stimulation levels within each range, with 1 being the lowest and 7 being the highest.
The default range setting is 2 or medium.
To change the range of stimulation, follow these steps:
1. Make sure your unit is off.
2. Then turn the unit on by pressing and releasing the on/off button.
3. After the Indicator Light turns off and within 5 seconds, press and hold the on/off button for 3
seconds.
4. The Collar Receiver will then beep once and the Indicator Light will flash orange. This indicates Low
stimulation range. If Medium or High are desired, continue to hold the button until the number of
beeps/orange flashes equals the desired stimulation range shown in the chart below.
5. Release the button once the desired range is selected; the Collar Receiver will turn off.
6. Turn the unit back on. It will then beep according to the stimulation range selected in Step 4.
STIMULATION RANGE DOG TEMPERAMENT
1 beep Low Mild
2 beeps Medium Moderate
3 beeps High Stubborn
STEP :: 03
STEP :: 04
400-1226.indd 10-11 6/11/10 4:27 PM

12 1-800-732-0144 WWW.SPORTDOG.COM 13
GeneraL traInInG tIpS
BEFORE TRAINING YOUR DOG WITH THIS PRODUCT:
You will have the most success using this remote trainer if you always remember to teach a command
before trying to reinforce the command with a remote trainer. We recommend that you read the
enclosed Training Guide and watch the enclosed DVD before training with this remote trainer. Your
training will be easier and proceed faster if you follow the guidelines in these teaching assistants. In
addition, always keep the following training tips in mind:
• Eliminate one misbehavior or teach one obedience command at a time. If you move too fast with the
training, your dog may become confused.
• Be consistent. Give your dog a tone, vibration and/or stimulation with each misbehavior.
• Do not overcorrect your dog. Use as few stimulations as possible to train your dog.
• Restrict your dog from situations in which he has a history of misbehaving unless you can supervise
him and use the HoundHunter® 3225 for applying tone, stimulation or vibration.
• If you notice one situation in which your dog misbehaves repeatedly, set up this situation as a
training session. This will dramatically increase your chances of success.
• If your dog has a timid reaction to the tone, stimulation or vibration (especially the first couple of
times), do not be alarmed. Redirect his attention to a simple and appropriate behavior (i.e. a known
command, such as “Sit”).
• Never use the HoundHunter 3225 to correct or eliminate any form of aggressive behavior. If your dog
exhibits such behavior, contact a professional trainer. Aggression in dogs is the result of many
factors – it may be a learned behavior or it may be brought on as a result of fear. Another factor
contributing to aggression in dogs is social dominance. Every dog is different.
At this point, your remote trainer is ready to use. The transmitter is factory set to mode 1, but you may
wish to change the mode to fit your situation. See Step 5, for an explanation of mode options.
proGram tHe remote tranSmItter
NOTE: The Transmitter is factory set to mode 1. The mode of the Remote Transmitter can be changed
to fit your type or style of training.
TO CHANGE THE MODE:
1. Referring to the following table, adjust the Intensity
Dial to the mode you want to use.
2. Turn the Remote Transmitter over and remove the belt
clip (if attached).
3. Using a pen or the tine on the buckle of your collar
strap, depress and release the mode button. When
the mode button is pressed, the Transmitter Indicator
Light will be solid in color. When it is released, it will
flash the mode selected.
For example, if mode 5 is desired, adjust the Intensity Dial to Level 5. Once the mode button has been
depressed, the Transmitter Indicator Light will be solid, and once the mode button is released, the
Transmitter Indicator Light will flash 5 times. However, if you select mode 7 (ID Code), the light will
remain solid in color once the mode button is released.
STEP :: 05
MODE UPPER
BUTTON
FUNCTION
LOWER
BUTTON
FUNCTION
SIDE
BUTTON
FUNCTION
TOGGLE
SWITCH
UP/DOWN
# OF
DOGS
V/T ON DIAL
1 Continuous
stimulation
(Level set by
intensity dial)
Momentary
stimulation
(Level set by
intensity dial)
Tone only Dog 1/Dog 2 2 * Neutral
If the dial is set to
V/T and any button
is pressed, then no
signal will be sent to
the receiver.
2 Continuous
stimulation
(Level set by
intensity dial)
Momentary
stimulation
(Level set by
intensity dial)
Vibration only Dog 1/Dog 2 2 * Neutral
If the dial is set to
V/T and any button
is pressed, then no
signal will be sent to
the receiver.
3 Continuous
stimulation
(Level set by
intensity dial)
Continuous
stimulation
(Level set by
intensity dial)
Continuous
stimulation
(Level set by
intensity dial)
Continuous/
Tone only
3 ** Neutral
If the dial is set to
V/T and any button
is pressed, then no
signal will be sent to
the receiver.
4 Continuous
stimulation
(Level set by
intensity dial)
Continuous
stimulation
(Level set by
intensity dial)
Continuous
stimulation
(Level set by
intensity dial)
Continuous/
Vibration only
3 ** Neutral
If the dial is set to
V/T and any button
is pressed, then no
signal will be sent to
the receiver.
5 Continuous
stimulation
(Level set by
intensity dial) –
Dog 1/4
Continuous
stimulation
(Level set by
intensity dial) –
Dog 2/5
Continuous
stimulation
(Level set by
intensity dial) –
Dog 3/6
Dog 1-3/4-6 6 ** Tone
6 Continuous
stimulation
(Level set by
intensity dial) –
Dog 1/4
Continuous
stimulation
(Level set by
intensity dial) –
Dog 2/5
Continuous
stimulation
(Level set by
intensity dial) –
Dog 3/6
Dog 1-3/4-6 6 ** Vibration
7 (ID
Code)
N/A N/A See Below *** Up Position N/A N/A
NOTE: Modes 1-6 provide 7 levels of stimulation, which correspond to the setting of the Intensity Dial.
* For two-dog operation setup refer to Step 7 on page 15.
** For three - six-dog operation setup refer to Step 8 on page 15.
*** An ID Code is the signal identification between the Remote Transmitter and Collar Receiver. Each
is programed in 1 of 4,000 ID Codes from the factory. In the rare event that a Remote Transmitter is
sending a signal to more than one Collar Receiver, you can change the Remote Transmitter’s ID
Code to prevent this from happening. There are 64 programmable ID Codes available.
400-1226.indd 12-13 6/11/10 4:27 PM

14 1-800-732-0144 WWW.SPORTDOG.COM 15
STEP :: 06
STEP :: 07STEP :: 08
TO MANUALLY PROGRAM THE REMOTE TRANSMITTER’S ID CODE FOLLOW THESE STEPS:
1 . Turn the intensity dial to level 7, flip the toggle switch up, and then press and release the mode
button on the back of your Remote Transmitter. This does not change the mode, so the current mode
will still be active after the ID change is complete.
2 . Once the mode button is released, the green indicator light will illuminate and stay on for
15 seconds.
3 . While the green light is on, turn the intensity dial to select the 1st digit of the ID, using 1-7, and then
press and release the side button. The green light will flash rapidly confirming selection.
4 . Again, while the green light is on, turn the intensity dial to select the 2nd digit of the ID, using 1-7,
and then press and release the side button. The green light will flash rapidly confirming selection.
The 2nd digit is optional, and if not desired, just wait until the green light turns off and refrain from
pressing the side button.
5 . At the end of 15 seconds, or after the second press of the side button, the green light will turn off
and the ID/frequency of the unit will be updated. At this point, the unit will be in the same mode it was
in prior to setting the ID.
6 . Upon changing the ID Code, you will need to match the Collar Receiver to the Remote Transmitter.
See Step 6 below.
NOTE: If you press the side button only once (skipping Step 4) the ID is still a two digit ID. The left digit
is defaulted to 1. For example, if you selected 6 in Step 3 and pressed the button only once, the ID you
get will be 16.
To return the unit to the factory ID either remove the battery or follow these steps:
1 . Turn the intensity dial to level 7, flip the toggle switch up, and then press and release the mode
button on the back of your Remote Transmitter. This does not change the mode, so the current mode
will still be active after the ID change is complete.
2 . Do not press any buttons and wait until the green indicator light turns off.
3 . You will now need to match the Collar Receiver to the Remote Transmitter. See Step 6 below.
matCH tHe CoLLar reCeIVer anD remote tranSmItter
To reset the Collar Receiver to work with a new Remote Transmitter or to reprogram a new Collar
Receiver to work with your existing Remote Transmitter:
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 5-6
seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin flashing as
normal. If this occurs, start over and repeat from A.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light
flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once
the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin
flashing as normal. If the Receiver Indicator Light does not flash 5 times, start over and repeat from A.
proGram tHe SyStem for tWo-DoG operatIon
SportDOG™ Collar Receivers can be set to respond to either the up or down toggle switch position.
A SportDOG SDR-AH Add-A-Dog® Collar Receiver must be purchased to train a second dog in two-
dog mode. Please refer to the back cover for other compatible Add-A-Dog Collar Receivers for this
system.
1. Program the Remote Transmitter to mode 1 or 2 (see page 13).
2. Then flip the toggle switch to the up position to program the first
Collar Receiver.
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light
will come on, then turn off in 4-5 seconds. If the On/Off Button
is released too early, the Receiver Indicator Light will begin its
normal flashing. If this occurs, start over and repeat from A.
C. After the Receiver Indicator Light has turned off, release the On/
Off Button.
TOGGLE SWITCH
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light
flashes 5 times.
3. Program the second Collar Receiver the same way using A through D above, but with the toggle
switch to the down position.
proGram tHe SyStem for tHree - SIX-DoG operatIon
A SportDOG™ SDR-AH Add-A-Dog® receiver(s) must be purchased to train additional dogs.
Please refer to the back cover for other compatible Add-A-Dog Collar Receivers for this system.
THREE DOG OPERATION
1. Program the Remote Transmitter to mode 3 or 4 (see page 13).
2. Program the first Collar Receiver:
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off in
4-5 seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin
its normal flashing. If this occurs, start over and repeat from A.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light
flashes 5 times. You may need to hold both units 2-3 feet from each other. If the Receiver
Indicator Light does not flash 5 times, start over and repeat from A.
3. Program the second Collar Receiver using A through D above, but using the Lower Button in
place of the Upper Button.
4. Program the third Collar Receiver using A through D above, but using the Side Button in place of
the Lower Button.
SIX DOG OPERATION
Program the Remote Transmitter to mode 5 or 6 (see page 13).
For six dog operation repeat above steps 2-4 with the toggle switch in the up position for dogs 1, 2,
and 3; then flip the toggle switch to the down position, and repeat above steps 2-4 for dogs 4, 5 and 6.
400-1226.indd 14-15 6/11/10 4:27 PM

16 1-800-732-0144 WWW.SPORTDOG.COM 17
aCCeSSorIeS
To purchase additional accessories for your SportDOG Brand® HoundHunter® 3225, contact the Customer Care
Center at 1-800-732-0144 or visit our website at www.sportdog.com to locate a retailer near you.
Component Part Number
3⁄4” Blaze Orange Collar Strap SAC00-10815
3⁄4” Blue Collar Strap SAC00-11921
3⁄4” Red Collar Strap SAC00-11820
3⁄4” Yellow Collar Strap SAC00-12795
3⁄4” Green Collar Strap SAC00-10817
3⁄4” White Collar Strap SAC00-12796
Collar Receiver (does not include collar
strap)
SDT[phone]
Remote Transmitter Only SDT[phone]
Remote Transmitter with antenna, belt
clip and lanyard
SDT[phone]
Antenna SAC00-12543
Contact Points (Short) SAC00-12571
Contact Points (Long) SAC00-12570
Lanyard SAC00-12799
Battery Kit (Collar Receiver) SAC00-12544
Battery Kit (Remote Transmitter) SAC00-12542
Belt Clip SAC00-12528
Car Charger SAC00-12482
Adapter SDT[phone]
Cradle SAC00-12541
freQUentLy aSKeD QUeStIonS
What purpose does V/T on the
intensity dial serve?
In modes 5 and 6, you have the flexibility of delivering tone or vibration
respectively, or stimulation to all 6 dogs.
Is the stimulation safe for my dog? While Continuous and/or Momentary stimulation may be unpleasant, it is
harmless to your dog. Electronic training devices require interaction and
training from the owner to achieve desired results.
How old does a dog have to be
before using the HoundHunter®
3225?
Your dog should be able to learn basic obedience commands such as “Sit”
or “Stay.” The Collar Receiver may be too large for dogs under 8 pounds.
Once my dog is trained and has
been obeying my commands, will
my dog have to continue to wear
the Collar Receiver?
Your dog may need to wear the Collar Receiver from time to time for
reinforcement. Also, many hunters keep the Collar Receiver on their dogs
while hunting for maximum control.
Is the Collar Receiver waterproof? Yes. If the rechargeable battery pack ever needs to be replaced, make sure
the o-ring and o-ring groove are free from dirt and debris.
Can my Collar Receiver be used
around salt water?
If the Collar Receiver is used in or around salt water, the Collar Receiver
should be rinsed with fresh water following each use.
Can I use the HoundHunter 3225
with more than one dog?
Yes, the HoundHunter 3225 is expandable to a maximum of 6 dogs.
SportDOG™ SDR-AH Add-A-Dog® Collar Receivers must be purchased.
Please refer to back cover for a list of other compatible Collar Receivers.
Can I use the HoundHunter 3225
on aggressive dogs?
We do not recommend any of our products to be used on aggressive dogs.
We recommend you contact your local veterinarian or professional trainer
to determine if your dog might be aggressive.
Will I get exactly two miles of
range with the HoundHunter
3225?
The range you get with your HoundHunter 3225 will vary according to
terrain, weather, vegetation, as well as transmission from other radio
devices. To get the maximum amount of range, please refer to “How the
System Works” section of this guide.
How long can I continuously
deliver stimulation to my dog?
The maximum amount of time you can press the Continuous Stimulation
Button and deliver stimulation to your dog continuously is 10 seconds. After
10 seconds, the Remote Transmitter will “time-out,” and the Continuous
Stimulation Button must be released and pressed again.
What do I do if my dog’s neck
becomes red and irritated?
This condition is due to the Contact Points irritating the skin. Discontinue
use of the Collar Receiver for a few days. If the condition persists beyond 48
hours, see your veterinarian. Once the skin returns to normal, resume use,
and monitor the skin condition closely.
The Intensity Dial seems difficult
to rotate. Is this normal?
Yes. This prevents accidental changes in intensity and encourages an
optimal waterproof seal. The knob will “break in” and be slightly easier to
turn as you use it.
Can I attach a leash to the
HoundHunter 3225?
DO NOT attach a leash to the HoundHunter 3225. You may put a separate
non-metallic collar on your dog’s neck and attach a leash. Be sure the extra
collar does not interfere with the Contact Points.
Can I program my HoundHunter
3225 to work with my other
SportDOG Brand® systems?
Yes. Your HoundHunter 3225 will also work with SportHunter® 1825,
SportHunter® 1225 and WetlandHunter® 1825 systems. The units will need
to be matched (see Step 6).
400-1226.indd 16-17 6/11/10 4:27 PM

18 1-800-732-0144 WWW.SPORTDOG.COM 19
troUBLeSHootInG
The answers to these questions should help you solve any problem you have with this system. If they do not,
please contact the Customer Care Center at 1-800-732-0144 or visit our website at www.sportdog.com.
My dog is not responding when I press
a button.
• Check to see if the Collar Receiver has been turned on.
• If your range has reduced from the first time you have used
it, please check to see if the battery is low in either the Remote
Transmitter or Collar Receiver.
• Many factors can impact the range you have with the
HoundHunter® 3225. For a list of these factors, please refer to
“How the System Works”.
• You can verify the Collar Receiver is delivering stimulation to
your dog by placing the test light, enclosed in your kit, on the
Collar Receiver. Please refer to the “Test Light Instructions”
section for details.
• Increase the Intensity Dial. Refer to “Find the Best Intensity
Level for Your Dog” for more information.
• Increase the Stimulation Range. Refer to “Changing Stimulation
Ranges” for more information.
• Make sure the Collar Receiver’s Contact Points are placed
snugly against your dog’s skin. Refer to “Fit the Collar Receiver”
for more information.
• You may need to switch to the longer Contact Points included
with your system or trim the hair beneath the Contact Points.
• If you notice your operating time dropping to about half the
original time, your Collar Receiver battery needs to be replaced.
Contact the Customer Care Center to purchase a new one.
The Collar Receiver will not turn on. • Make sure the Collar Receiver has been charged. The Collar
Receiver will charge in 2 hours.
The Collar Receiver is not responding
to the Remote Transmitter.
• Verify the Collar Receiver has been turned on. Refer to “Turning
the Collar Receiver On and Off”.
• Refer to “Match the Collar Receiver.”
teSt LIGHt InStrUCtIonS
1. Turn the Collar Receiver on.
2. Hold the Test Light Contacts to the Contact Points.
3. Press a Stimulation Button on the Remote Transmitter.
4. The Test Light will flash.
NOTE: At higher Stimulation Levels, the Test Light will flash brighter.
5. Turn the Collar Receiver off.
Save the Test Light for future testing.
NOTE: If the Test Light does not flash, recharge the battery and re-test. If the Test Light still does not flash, contact
the Customer Care Center at 1-800-732-0144.
termS of USe anD LImItatIon of LIaBILIty
1. TERMS OF USE
This Product is offered to you conditioned upon your acceptance without modification of the terms, conditions
and notices contained herein. Usage of this Product implies acceptance of all such terms, conditions, and
notices.
2. PROPER USE
This Product is designed for use with dogs where training is desired. The specific temperament of your dog
may not work with this Product. We recommend that you not use this Product if your dog is less than 8 pounds
or if your dog is aggressive. If you are unsure whether this is appropriate for your dog, please consult your
veterinarian, certified trainer or contact our Customer Care Center at 1-800-732-0144.
Proper use includes reviewing the entire Operating and Training Guide provided with your Product and any
specific Caution statements.
3. NO UNLAWFUL OR PROHIBITED USE
This Product is designed for use with dogs only. This dog training device is not intended to harm, injure, or
provoke. Using this Product in a way that is not intended could result in violation of Federal, State or local
laws.
4. LIMITATION OF LIABILITY
In no event shall Radio Systems® Corporation be liable for any direct, indirect, punitive, incidental, special or
consequential damages, or any damages whatsoever arising out of or connected with the use or misuse of this
Product. Buyer assumes all risks and liability from the use of this Product.
5. MODIFICATION OF TERMS AND CONDITIONS
Radio Systems Corporation reserves the right to change the terms, conditions and notices under which this
Product is offered.
400-1226.indd 18-19 6/11/10 4:27 PM

20 1-800-732-0144 WWW.SPORTDOG.COM 21
fCC CompLIanCe
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a specific installation. If interference does
occur to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Contact customer service or an experienced radio/TV technician for assistance.
Caution: Unauthorized changes or modifications to the equipment may violate FCC regulations and could void the
user’s authority to operate the equipment.
CUStomer Care InternatIonaL
Australia:
Tel: [phone]
Monday - Friday 8 AM - 5 PM
New Zealand:
Tel: [phone]
Monday - Friday 12 PM - 7 PM
Canada:
Tel: [phone]
Monday - Friday 8 AM - 8 PM/Saturday 9 AM - 5 PM
Lundi - Vendredi 8h00 à 20h00/Samedi 9h00 à 17h00
Battery DISpoSaL
WARNING
This device contains a Lithium-Ion (Li-Ion) battery; never incinerate, puncture, deform, short-
circuit, or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if
this warning is not followed.
This system operates on two Li-Ion battery packs (240mAh capacity for the Collar Receiver and 550mAh capacity
for the Remote Transmitter). Only replace with battery received from calling the Customer Care Center at
1-800-732-0144.
Separate collection of spent batteries is required in many regions; check the regulations in your area before
discarding spent batteries. Please see below for instructions on how to remove the battery from the product for
separate disposal.
AT END OF PRODUCT LIFE, USE THESE BATTERY REMOVAL INSTRUCTIONS FOR FINAL DISPOSAL (DO NOT
OPEN THE COLLAR RECEIVER OR REMOTE TRANSMITTER UNTIL YOU HAVE RECEIVED THE REPLACEMENT):
• Using a #1 Phillips screwdriver for your Remote Transmitter and/or a 3/32 Allen wrench for your Collar Receiver,
remove the case screws.
• Remove the case back or cover.
• Remove the old battery pack.
NOTE: When removing the old battery pack, care must be taken when gripping the
connector firmly to avoid damaging the wires. Shorting the battery wires may cause fire or explosion.
WARNING
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.
NOTE: These instructions are not valid for repair or battery replacement. Replacing the battery with a battery not
specifically approved by Radio Systems® Corporation may cause fire or explosion. Please call the Customer Care
Center at 1-800-732-0144 to avoid invalidating your warranty.
This product is protected by the following patents:
U.S. Patent Numbers: 7,647,545; 6,901,883; 7,017,524; 6,184,790; 6,459,378.
400-1226.indd 20-21 6/11/10 4:27 PM

22 1-800-732-0144 WWW.SPORTDOG.COM 23
400-1226.indd 22-23 6/11/10 4:27 PM

Radio Systems® Corporation • 10427 Electric Avenue • Knoxville, TN 37932 • 1-800-732-0144
400-1226
©2010 RADIO SYSTEMS® CORPORATION
HOUNDHUNTER®
COLLAR STRAPS
(AVAILABLE COLORS)
SDR::AH ADD-A-DOG®
NOTE: SDR-FS, SDR-FH, SDR, SDR-CH, SDR-FC, SDR-BEEP AND SDR-H ADD-A-DOG COLLARS ARE NOT COMPATIBLE WITH THIS SYSTEM.
Collar Receiver & Replacement Collar Straps
OTHER COMPATIBLE COLLARS INCLUDE: SDR-A & SDR-AW ADD-A-DOG®
400-1226.indd 24 6/11/10 4:27 PM