SportDOG SD-1825CAMO Owner's manual

PROGRAM THE REMOTE TRANSMITTER
NOTE: The Transmitter is factory set to mode 1. The mode of the Remote Transmitter can be changed
to fit your type or style of training.
TO CHANGE THE MODE:
For example, if mode 5 is desired, adjust the Intensity Dial to Level 5. Once the mode button has been
depressed, the Transmitter Indicator Light will be solid, and once the mode button is released, the
Transmitter Indicator Light will flash 5 times. However, if you select mode 8 (ID Code) in the UP position
or mode 2 in the DOWN position, the light will remain solid in color once the mode button is released.
1. Referring to the following tables, adjust the Intensity
Dial and Toggle Switch to the mode you want to use.
2. Turn the Remote Transmitter over and remove the belt
clip (if attached).
3. Using a pen or the tine on the buckle of your collar
strap, depress and release the mode button. When
the mode button is pressed, the Transmitter Indicator
Light will be solid in color. When it is released, it will
flash the mode selected.
SD-1825CAMO
TOGGLE SWITCH IN
THE UP POSITION
TOGGLE SWITCH IN
THE DOWN POSITION

TOGGLE SWITCH IN THE UP POSITION
MODE UPPER BUTTON
FUNCTION
LOWER BUTTON
FUNCTION
SIDE BUTTON
FUNCTION
TOGGLE
SWITCH
(up/down)
NUMBER
OF DOGS
1Continuous
stimulation (Level set
by intensity dial)
Momentary
stimulation (Level set
by intensity dial)
Tone only Dog 1 /
Dog 2
2
2Continuous
stimulation (Level set
by intensity dial)
Low Continuous
stimulation (Level set
by intensity dial)
Tone only Continuous/
Momentary
1
3Continuous
stimulation (Level set
by intensity dial)
Continuous
stimulation (Level set
by intensity dial)
Continuous
stimulation (Level set
by intensity dial)
Dogs 1-3 /
Dogs 4-6
6
4Continuous
stimulation (Level set
by intensity dial)
Tone only Remote Beeper
(SD-BEEP)
Call/Locate Mode -
single tone*
Dog 1 /
Dog 2
2
5Continuous
stimulation (Level set
by intensity dial)
Momentary
stimulation (Level set
by intensity dial)
Remote Beeper
(SD-BEEP)
Call/Locate Mode -
single tone*
Dog 1 /
Dog 2
2
6N/A N/A N/A N/A N/A
7Continuous
stimulation followed
by a ¼ second delay
tone (Level set by
intensity dial)
Momentary
stimulation followed
by a ¼ second delay
tone (Level set by
intensity dial)
Continuous
stimulation + 2
Dog 1 /
Dog 2
2
8 (ID
Code)
N/A N/A See below** Up position N/A
NOTE: Modes 1, 3, 4 ,5 and 7 provide 8 levels of stimulation, which correspond to the setting of the
Intensity Dial.
Mode 2 provides more “increments” to choose from – a total of 16 levels of stimulation. For example,
in mode 2 with the Intensity Dial set at 2, the lower button provides level 3 of 16 and the upper button
provides level 4 of 16.
* To enable Run Mode, press and hold the corresponding Locate Button for 3 seconds.
** An ID Code is the signal identification between the Remote Transmitter and Collar Receiver. Each
is programed in 1 of 4,000 ID Codes from the factory. In the rare event that a Remote Transmitter is
sending a signal to more than one Collar Receiver, you can change the Remote Transmitter’s ID
Code to prevent this from happening. There are 64 programmable ID Codes available.

TO MANUALLY PROGRAM THE REMOTE TRANSMITTER’S ID CODE FOLLOW THESE STEPS:
1 . Turn the intensity dial to level 8, flip the toggle switch up, and then press and release the mode
button on the back of your Remote Transmitter. This does not change the mode, so the current mode
will still be active after the ID change is complete.
2 . Once the mode button is released, the green indicator light will illuminate and stay on for
15 seconds.
3 . While the green light is on, turn the intensity dial to select the 1st digit of the ID and then press and
release the side button. The green light will flash rapidly confirming selection.
4 . Again, while the green light is on, turn the intensity dial to select the 2nd digit of the ID and then
press and release the side button. The green light will flash rapidly confirming selection. The 2nd
digit is optional, and if not desired, just wait until the green light turns off and refrain from pressing
the side button.
5 . At the end of 15 seconds, or after the second press of the side button, the green light will turn off
and the ID/frequency of the unit will be updated. At this point, the unit will be in the same mode it was
in prior to setting the ID.
6 . Upon changing the ID Code, you will need to match the Collar Receiver to the Remote Transmitter.
NOTE: If you press the side button only once (skipping Step 4) the ID is still a two digit ID. The left digit
is defaulted to 1. For example, if you selected 6 in Step 3 and pressed the button only once, the ID you
get will be 16.
To return the unit to the factory ID either remove the battery or follow these steps:
1 .Turn the intensity dial to level 8, flip the toggle switch up, and then press and release the mode
button on the back of your Remote Transmitter. This does not change the mode, so the current mode
will still be active after the ID change is complete.
2 . Do not press any buttons and wait until the green indicator light turns off.
3 . You will now need to match the Collar Receiver to the Remote Transmitter.

TOGGLE SWITCH IN THE DOWN POSITION
MODE UPPER BUTTON
FUNCTION
LOWER BUTTON
FUNCTION
SIDE BUTTON
FUNCTION
TOGGLE
SWITCH
(up/down)
NUMBER
OF DOGS
1Medium Continuous
stimulation
Low Continuous
stimulation
High Continuous
stimulation
Dog 1 /
Dog 2
2
2Continuous
stimulation (Level set
by intensity dial)
Low Continuous
stimulation (Level set
by intensity dial)
Programmable
Continuous
stimulation**
Dog 1 /
Dog 2
2
3Continuous
stimulation (Level set
by intensity dial)
Tone w/ one second
delay Continuous
stimulation
Vibration only Dog 1 /
Dog 2
2
4Continuous
stimulation (Level set
by intensity dial)
Low Continuous
stimulation (Level set
by intensity dial)
Vibration only Continuous/
Momentary
1
5Dog 1 (Level set by
intensity dial)
Dog 2 (Level set by
intensity dial)
Dog 3 (Level set by
intensity dial)
Continuous/
Vibration
3
6Continuous
stimulation (Level set
by intensity dial)
Tone only Vibration only Dog 1 /
Dog 2
2
7Continuous
stimulation (Level set
by intensity dial)
Vibration only Remote Beeper
(SD-BEEP)
Call/Locate Mode -
single tone*
Dog 1 /
Dog 2
2
8N/A N/A N/A N/A N/A
NOTE: Modes 1, 3, 5 ,6 and 7 provide 8 levels of stimulation, which correspond to the setting of the
Intensity Dial.
Modes 2 and 4 provide more “increments” to choose from – a total of 16 levels of stimulation. For
example, in mode 2 with the Intensity Dial set at 2, the lower button provides level 3 of 16 and the
upper button provides level 4 of 16.
* To enable Run Mode, press and hold the corresponding Locate Button for 3 seconds.
** After selecting mode 2 and while the green indicator light is still solid in color, turn the intensity
dial to the desired Continuous Stimulation level and press the side button to set the level. The
green light will quickly flash acknowledging your selection. For example, if you turned the
intensity dial to 3, the side button on your Remote Transmitter will transmit Continuous Stimulation
at level 3 when pressed. If no level is selected after 15 seconds, it will default to level 8.