SportDOG SPORT HUNTER 1600M User manual

OPERATING GUIDE
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING

2SPORTDOG.COM
Hereinafter Radio Systems Corporation, Radio Systems PetSafe Europe Ltd., Radio Systems Australia Pty Ltd.
and any other affiliate or Brand of Radio Systems Corporation may be referred to collectively as “We” or “Us”.
IMPORTANT SAFETY INFORMATION
Explanation of Attention Words and Symbols used in this guide
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
WARNING indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION, used without the safety alert symbol, indicates a hazardous situation which,
if not avoided, could result in harm to your dog.

3SPORTDOG.COM
• Not for use with aggressive dogs. Do not use this product if your dog is aggressive or if your dog is prone to
aggressive behaviour. Aggressive dogs can cause severe injury and even death to their owner and others.
If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or a
certified trainer.
• This device contains Lithium-Ion (Li-Ion) batteries; never incinerate, puncture, deform, short-circuit, or
charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this
warning is not followed.
• Risk of explosion if battery is replaced by an incorrect type. Dispose of spent batteries according to the
regulations in your area.
• Batteries should never be removed from the battery compartment for charging.
• Risk of explosion if batteries are charged in areas with high temperature (38° C / 100° F+).
Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for
too long or made too tight on the dog’s neck may cause skin damage. This is called bed sores; it is also called
decubitus ulcers or pressure necrosis.
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible, reposition the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the Collar Receiver; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
For additional information on bed sores and pressure necrosis, please visit our website at www.sportdog.com.
These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable while they wear
stainless steel contacts. Some dogs are sensitive to contact pressure. You may find after some time that your
dog is very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue daily
checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed.
• You may need to trim the hair in the area of the Contact Points or switch to the longer Contact Points to
ensure consistent contact. Never shave the dog’s neck; this may lead to a rash or infection.
• You should not make the collar any tighter than is required for good contact. A collar that is too tight will
increase the risk of pressure necrosis in the contact area.

4SPORTDOG.COM
Thank you for choosing SportDOG®Brand training products. Used properly, this product will help you train your
dog efficiently and safely. To ensure your satisfaction, please review this Operating Guide thoroughly. If you
have questions regarding this product’s operation, please see this manual’s Frequently Asked Questions and
Troubleshooting sections or contact our Customer Care Centre. For a listing of telephone numbers in your area,
visit our website at www.sportdog.com.
To get the most protection out of your warranty, please register your product within 30 days at
www.sportdog.com. By registering and keeping your receipt you will enjoy the product’s full warranty and,
should you ever need to call the Customer Care Centre, we will be able to help you faster. Most importantly, your
valuable information will never be given or sold to anyone. Complete warranty information is available online at
www.sportdog.com.
TRAINING GUIDE
Please visit our website at www.sportdog.com to download a detailed Training Guide for this unit or contact our
Customer Care Centre for further assistance. For a listing of telephone numbers in your area, visit our website at
www.sportdog.com.
TABLE OF CONTENTS
COMPONENTS 5
HOW THE SYSTEM WORKS 5
KEY DEFINITIONS 6
PREPARE THE REMOTE TRANSMITTER 7
PREPARE THE COLLAR RECEIVER 8
FIT THE COLLAR RECEIVER 11
FIND THE BEST INTENSITY LEVEL FOR YOUR DOG 12
CHANGE STATIC STIMULATION RANGES 12
GENERAL TRAINING TIPS 13
PROGRAM THE REMOTE TRANSMITTER 14
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER 17
PROGRAM THE SYSTEM FOR TWO-DOG OPERATION 17
PROGRAM THE SYSTEM FOR THREE-DOG TO SIX-DOG OPERATION 18
CHANGE ID CODES 19
ACCESSORIES 19
FREQUENTLY ASKED QUESTIONS 20
TROUBLESHOOTING 21
TEST LIGHT TOOL INSTRUCTIONS 21
TERMS OF USE AND LIMITATION OF LIABILITY 22
COMPLIANCE 22
BATTERY DISPOSAL 23
IMPORTANT RECYCLING ADVICE 23
WARRANTY 23

5SPORTDOG.COM
COMPONENTS
HOW THE SYSTEM WORKS
The SportDOG®SportHunter™SD-1525E Multi-Dog Remote Trainer has been proven safe, comfortable, and
effective for all dogs over 3.6 kg. This system is designed to easily operate with up to 6 dogs. Consistent, correct
use of this product allows you to reinforce commands and correct misbehaviour from up to 1600 metres in a
multiple dog setting. The Remote Transmitter sends a signal, activating the Collar Receiver to deliver a harmless
stimulation. With proper training, a dog will learn to associate this signal with a command. Like all SportDOG®
products, this model features adjustable static stimulation levels so you can tailor the stimulation level to each
dogs’ temperament, eliminating the risk of over-stimulation.
IMPORTANT: THE SPORTHUNTER™SD-1525E MULTI-DOG REMOTE TRAINER HAS
A RANGE OF UP TO 1600 M. DEPENDING ON THE WAY YOU HOLD THE REMOTE
TRANSMITTER, THE MAXIMUM RANGE MAY VARY. FOR CONSISTENT RESULTS AT
LONGER RANGES, HOLD THE REMOTE TRANSMITTER IN A VERTICAL POSITION AWAY
FROM YOUR BODY AND ABOVE YOUR HEAD. TERRAIN, WEATHER, VEGETATION,
TRANSMISSION FROM OTHER RADIO DEVICES, AND OTHER FACTORS WILL AFFECT THE
MAXIMUM RANGE.
Do not use this product if your dog is aggressive or if your dog is prone to aggressive behaviour. Aggressive
dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product
is appropriate for your dog, please consult your veterinarian or a certified trainer.

6SPORTDOG.COM
KEY DEFINITIONS
REMOTE TRANSMITTER: Transmits the radio signal to the Collar Receiver. It is waterproof and can be submerged in
water to a depth of 7.6 m.
INTENSITY DIAL: Provides multiple levels and types of stimulation so you can match the stimulation to each
dogs’ temperament.
TRANSMITTER INDICATOR LIGHT: Indicates that a button is pressed and also serves as a low-battery indicator.
TOGGLE SWITCH: This switch is factory-set so that the Remote Transmitter can control two Collar Receivers.
UPPER BUTTON: This button is factory-set to deliver continuous static stimulation.
LOWER BUTTON: This button is factory-set to deliver momentary static stimulation, or a “Nick”.
SIDE BUTTON: This button is factory-set to deliver a tone without static stimulation.
CHARGING JACK: For connecting the charger. Although the Remote Transmitter is waterproof without it, keep the cover
in place when not charging to keep debris out of the opening.
MODE BUTTON: This button gives you the ability to change the mode of your Remote Transmitter.
COLLAR RECEIVER: Receives the radio signal from the Remote Transmitter and delivers the static, vibration, or tone
stimulation for correcting or cueing your dogs. It is waterproof and can be submerged in water to a depth of 7.6 m.
RECEIVER INDICATOR LIGHT: Indicates when the Collar Receiver has been turned on or off, serves as a low-battery
indicator, and also indicates when a continuous or momentary static stimulation button is pressed.
CONTACT POINTS: The contacts through which the Collar Receiver delivers static stimulation.
ON/OFF BUTTON: Momentarily pressing and releasing this button turns the Collar Receiver on and off.
THE COLLAR RECEIVER IS CAPABLE OF DELIVERING FOUR TYPES OF STIMULATION:
CONTINUOUS: You control both when and how long static stimulation is delivered, up to a maximum of 10 seconds.
After 10 seconds, the static stimulation will “time out” and static stimulation cannot be delivered to your dog for 5
seconds. After the 5 second “time-out” period, static stimulation can be delivered again.
MOMENTARY (NICK): Static stimulation is delivered for 1/10 of a second, regardless of how long the button is pressed.
TONE: The Collar Receiver will make a rapid beeping noise when a Tone button is pressed.
VIBRATION: The Collar Receiver will vibrate when a Vibration button is pressed, up to a maximum of 10 seconds.
After 10 seconds, the Remote Transmitter will “time out” and vibration stimulation cannot be delivered to your dog for
5 seconds. After the 5 second “time-out” period, vibration stimulation can be delivered again.
TRANSMITTER INDICATOR
LIGHT
INTENSITY DIAL
TRANSMITTER
ANTENNA
SIDE BUTTON
LOWER BUTTON
UPPER
BUTTON
CHARGING JACK
TOGGLE SWITCH
CONTACT POINTS
RECEIVER
INDICATOR LIGHT
ON/OFF BUTTON

7SPORTDOG.COM
STEP::01
PREPARE THE REMOTE TRANSMITTER
CHARGE THE REMOTE TRANSMITTER
1. Lift the rubber cover protecting the Charging Jack.
2. Connect one of the charger connectors to the
Charging Jack.
3. Plug the charger into a standard wall outlet.
4. Charge the Remote Transmitter for 2 hours for the first
charge and every charge thereafter.
Using Lithium-Ion technology, the Remote Transmitter
only requires a 2 hour charge. It is not harmful to let the
unit charge for more than 2 hours.
5. When charging is complete, replace the rubber cover.
NOTE: Approximate battery life between charges is 40 to
60 hours, depending on frequency of use.
TRANSMITTER INDICATOR LIGHT
OPERATIONAL MODE LIGHT COLOUR BATTERY STATUS LIGHT FUNCTION
Continuous static tone, or
vibration stimulation pressed Green Good Light is solid in colour while button is pressed
Continuous static, tone, or
vibration stimulation pressed Red Low Light is solid in colour while button is pressed
Momentary static stimulation
button pressed Green Good Light flashes once and turns off
Momentary static stimulation
button pressed Red Low Light flashes once and turns off
Unit is charging Green Low Light is solid in colour
while charging
Unit is fully charged (charger
still connected) Green Good
Light flashes once per
second once the battery is
completely charged
CHARGER CONNECTOR
PLACED IN THE
REMOTE TRANSMITTER
CHARGING JACK

8SPORTDOG.COM
STEP::02
PREPARE THE COLLAR RECEIVER
CHARGE THE COLLAR RECEIVER
1. Lift the rubber cover protecting the Charging Jack.
2. Connect one of the charger connectors to the Charging Jack.
3. Plug the charger into a standard wall outlet.
4. Charge the Collar Receiver for 2 hours for the first charge and
every charge thereafter.
Using Lithium-Ion technology, the Collar Receiver only requires a 2
hour charge. It is not harmful to let the unit charge for more
than 2 hours.
5. When charging is complete, replace the rubber cover.
TO TURN THE COLLAR RECEIVER ON
Press and release the On/Off Button. The Receiver Indicator Light will come on solid green and the Collar
Receiver will beep 1 - 2 times depending on what static stimulation range is chosen. The default is 2 (medium).
TO TURN THE COLLAR RECEIVER OFF
Press and release the On/Off Button. The Receiver Indicator Light will come on solid red and the Collar Receiver
will beep continuously for 2 seconds.
To extend the life between charging cycles, turn the Collar Receiver off when it is not in use.
NOTE: Approximate battery life between charges is 50 to 70 hours, depending on frequency of use.
ON/OFF BUTTON
CHARGER CONNECTOR PLACED
IN THE COLLAR RECEIVER
CHARGING JACK

9SPORTDOG.COM
RECEIVER INDICATOR LIGHT
OPERATIONAL
MODE
LIGHT
COLOUR
BATTERY
STATUS LIGHT FUNCTION SPEAKER FUNCTION VIBRATION
Unit is turned on via
On/Off Button Green Good Light is solid in colour during beep sequence
Beeps 1-2 times
depending on static
stimulation range
setting (2 is the
default). Please see
page 12.
N/A
Unit is turned on via
On/Off Button Red Low Light is solid in colour during beep sequence
Unit is turned off via
On/Off Button Red N/A Light is solid in colour during beep sequence
Beeps continuously
for 2 seconds N/A
Unit is on Green Good Light flashes every
2 seconds N/A N/A
Unit is on Red Low Light flashes every
2 seconds N/A N/A
Unit is delivering
continuous static
stimulation
Red N/A
Light is solid in colour
for as long as button
is pressed (up to 10
seconds)
N/A N/A
Unit is delivering
momentary (nick)
static stimulation
Red N/A
Light will quickly flash
once no matter how long
button is pressed
N/A N/A
Unit is delivering
tone stimulation Off N/A N/A
Unit will beep for
as long as button
is pressed
N/A
Unit is delivering
vibration
stimulation
Off N/A N/A N/A
Unit will
vibrate for as
long as button
is pressed (up
to 10 seconds)
Unit is changing
static stimulation
range
Orange N/A
Light flashes 1-2 times
depending on desired
static stimulation range.
Beeps 1-2 times
depending on static
stimulation range
setting (2 is the
default). Please see
page 12.
N/A
Unit is charging Green Low Light is solid in colour
while charging N/A N/A
Unit is fully charged
(charger still
connected)
Green Good
Light flashes once per
second once the battery
is completely charged
N/A N/A

10 SPORTDOG.COM
RECHARGEABLE BATTERIES
• This device contains Lithium-Ion (Li-Ion) batteries; never incinerate, puncture, deform, short-circuit, or
charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this
warning is not followed.
• Risk of explosion if battery is replaced by an incorrect type. Dispose of spent batteries according to the
regulations in your area.
• Batteries should never be removed from the battery compartment for charging.
• Risk of explosion if batteries are charged in areas with high temperature (38° C / 100° F+).
• The rechargeable Lithium Ion (Li-Ion) batteries are not memory sensitive, do not require depletion before
charging, and cannot be over charged.
• The batteries come partially charged from the factory, but will require a full charge before the first use.
• When storing the unit for long periods, remember to regularly give batteries a full charge. This should be
done once every 3 to 4 months.
• You should expect hundreds of recharge cycles from your batteries. However, all rechargeable batteries
lose capacity over time relative to the number of recharge cycles they experience. This is normal. If your
operating time drops to half of the original life, contact the Customer Care Centre to purchase a new battery.
• The batteries should last for a period of 3-5 years. When a battery needs replacement, you can order a new
pack by calling our Customer Care Centre. For a listing of telephone numbers in your area, visit our website
at www.sportdog.com. Please do not open the Collar Receiver or Remote Transmitter until you have received
the replacement.

11 SPORTDOG.COM
STEP::03
FIT THE COLLAR RECEIVER
IMPORTANT: The proper fit and placement of the Collar Receiver is important for effective training. The Contact
Points must have direct contact with your dog’s skin.
Please see page 3 for Important Safety Information.
To ensure a proper fit, follow these steps:
1. With your dog standing (3A), center the
Collar Receiver so the Contact Points are
underneath your dog’s neck, touching the
skin (3B). If your dog has a long or thick coat,
you have two options to ensure consistent
contact: either trim the hair around the
Contact Points or switch to the longer
Contact Points included with your system.
• You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck; this may lead to
a rash or infection.
• You should not make the collar any tighter than is required for good contact. A collar that is too tight will
increase the risk of pressure necrosis in the contact area.
2. The Collar Receiver should fit snugly, yet loose enough to allow one finger to fit
between the strap and your dog’s neck (3C).
3. Allow your dog to wear the collar for several minutes, and then recheck the
fit. Check the fit again as your dog becomes more comfortable wearing the
Collar Receiver.
3A 3B
3C

12 SPORTDOG.COM
STEP::04
FIND THE BEST INTENSITY LEVEL FOR YOUR DOG
The SportHunter™SD-1525E has multiple intensity levels. This allows you to choose the static stimulation that is
best for your dog.
NOTE: Always start at the lowest level and work your way up.
For training efficiency, it is important to find the right intensity level for your dog. This is called the “Recognition
Level”, and is the level at which your dog looks around in curiosity or flicks his ears.
TO FIND YOUR DOG’S RECOGNITION LEVEL
NOTE: Every dog is different and you cannot predict where your dog’s Recognition Level will be. Watch closely for
any slight change in behaviour that demonstrates your dog is feeling the static stimulation.
1. With the Collar Receiver turned on and properly fitted to your dog, set the Remote Transmitter’s Intensity
Dial at Level 1 and press the Continuous Static Stimulation Button for 1 to 2 seconds.
2. If your dog shows no reaction to Level 1, go to Level 2 and repeat the process.
3. YOUR DOG SHOULD NOT VOCALIZE OR PANIC WHEN RECEIVING STATIC STIMULATION. IF THIS HAPPENS,
THE STATIC STIMULATION LEVEL IS TOO HIGH AND YOU NEED TO GO BACK TO THE PREVIOUS LEVEL AND
REPEAT THE PROCESS.
4. Once you find your dog’s Recognition Level, this is the level you should use when you begin a
training exercise.
5. If you have progressed to Level 7 while searching for your dog’s Recognition Level and your dog continues
to show no response, check to see if the Collar Receiver is snug against your dog’s neck. Then go back to
Intensity Level 1 and repeat the process. If your dog still does not indicate he is feeling the static stimulation,
you have three options: trim the hair beneath the Contact Points, switch to the longer Contact Points included
in your system, or change the static stimulation range.
If after completing all of these steps your dog still does not indicate he is feeling the static stimulation, please
contact the Customer Care Centre.
CHANGE STATIC STIMULATION RANGES
The SportHunter™SD-1525E Collar Receiver has 2 static stimulation ranges (low and medium). There are 7 static
stimulation levels within each range, with 1 being the lowest and 7 being the highest. The default range setting is
2 (medium).
To change the range of static stimulation, follow these steps:
1. Make sure the Collar Receiver is off.
2. Turn the unit on by pressing and releasing the On/Off Button.
3. Within 5 seconds of the Indicator Light turning off, press and hold the On/Off Button for 3 seconds.
4. The Collar Receiver will then beep once and the Indicator Light will flash orange. This indicates Low static
stimulation range. If Medium is desired, continue to hold the On/Off Button until the number of beeps/orange
flashes equals the desired static stimulation range, as shown in the chart below.
5. Release the On/Off Button once the desired range is selected; the Collar Receiver will turn off.
6. Turn the unit back on. It will then beep according to the static stimulation range selected.
STATIC STIMULATION RANGE DOG TEMPERAMENT
1 beep Low Mild
2 beeps Medium Moderate

13 SPORTDOG.COM
GENERAL TRAINING TIPS
BEFORE TRAINING YOUR DOG WITH THIS PRODUCT
You will have the most success using this Remote Trainer if you always remember to teach a command before
trying to reinforce the command with the Remote Trainer. Always keep the following training tips in mind:
• Eliminate one misbehaviour or teach one obedience command at a time. If you move too fast with the training,
your dog may become confused.
• Be consistent. Give your dog a static, tone, or vibration stimulation with each misbehaviour.
• Do not overcorrect your dog. Use as few stimulations as possible to train your dog.
• Restrict your dog from situations in which he has a history of misbehaving unless you can supervise him and
use the Remote Trainer for applying static, tone, or vibration stimulation.
• If you notice one situation in which your dog misbehaves repeatedly, set up this situation as a training session.
This will dramatically increase your chances of success.
• If your dog has a timid reaction to the static, tone, or vibration stimulation (especially the first couple
of times), do not be alarmed. Redirect his attention to a simple and appropriate behaviour (i.e. a known
command, such as “Sit”).
• Never use the Remote Trainer to correct or eliminate any form of aggressive behaviour. If your dog exhibits
such behaviour, contact a professional trainer. Aggression in dogs is the result of many factors. It may be a
learned behaviour or it may be brought on as a result of fear. Another factor contributing to aggression in
dogs is social dominance. Every dog is different.
Visit our website at www.sportdog.com to find more detailed training tips and guides or contact our Customer
Care Centre for further assistance. For a listing of the phone numbers in your area, visit our website at
www.sportdog.com.
At this point, your SportHunter™SD-1525E Multi-Dog Remote Trainer is ready to use. The Remote Transmitter is
factory set to mode 1 in the Toggle Switch UP position, but you may wish to change the mode to fit your situation.
See STEP::05 for an explanation of mode options.

14 SPORTDOG.COM
STEP::05
PROGRAM THE REMOTE TRANSMITTER
The SportHunter™SD-1525E Remote Transmitter has 12 operational modes to allow you to select the best match
for your type or style of training. The Remote Transmitter is factory set to mode 1 in the Toggle Switch
UP position.
TO CHANGE THE MODE
Referring to the following tables, adjust the Intensity Dial and
Toggle Switch to your desired mode.
Turn the Remote Transmitter over (remove the belt clip if attached).
Using a pen or the tine on the buckle of your collar strap, press
and release the Mode Button. When the Mode Button is pressed,
the Transmitter Indicator Light will be solid in colour. When it is
released, it will flash the number of times for the mode selected.
For example, mode 5 would flash 5 times.
NOTE: If mode 7 (ID Code) in the UP position is selected, the Transmitter Indicator Light will remain solid in colour
when the Mode Button is released.
TOGGLE SWITCH IN
THE UP POSITION
TOGGLE SWITCH IN
THE DOWN POSITION

15 SPORTDOG.COM
TOGGLE SWITCH IN THE UP POSITION
MODE UPPER BUTTON
FUNCTION
LOWER BUTTON
FUNCTION
SIDE BUTTON
FUNCTION
TOGGLE
SWITCH
(UP/DOWN)
NUMBER
OF DOGS V/T ON DIAL
1
Continuous static
stimulation
(Level set by Intensity
Dial)
Momentary static
stimulation
(Level set by
Intensity Dial)
Tone
stimulation only Dog 1 / Dog 2 2 Vibration
2
Continuous static
stimulation
(Level set by Intensity
Dial)
Momentary static
stimulation
(Level set by
Intensity Dial)
Vibration
stimulation only Dog 1 / Dog 2 2 Tone
3
Dog 1
(Level set by Intensity
Dial)
Dog 2
(Level set by
Intensity Dial)
Dog 3
(Level set by
Intensity Dial)
Continuous /
Tone only 3Vibration
4
Dog 1
(Level set by Intensity
Dial)
Dog 2
(Level set by
Intensity Dial)
Dog 3
(Level set by
Intensity Dial)
Continuous /
Vibration only 3Tone
5
Dog 1
(Level set by Intensity
Dial)
Dog 2
(Level set by
Intensity Dial)
Dog 3
(Level set by
Intensity Dial)
Continuous /
Momentary 3Tone
6
Dog 1
(Level set by Intensity
Dial)
Dog 2
(Level set by
Intensity Dial)
Dog 3
(Level set by
Intensity Dial)
Continuous /
Momentary 3Vibration
7 (ID
Code) N/A N/A See STEP::09 UP Position N/A N/A
V/T N/A N/A N/A N/A N/A N/A

16 SPORTDOG.COM
TOGGLE SWITCH IN THE DOWN POSITION
MODE UPPER BUTTON
FUNCTION
LOWER BUTTON
FUNCTION
SIDE BUTTON
FUNCTION
TOGGLE SWITCH
(UP/DOWN)
NUMBER
OF DOGS
V/T ON
DIAL
1
Continuous static
stimulation
(Level set by
Intensity Dial)
Dog 1 / Dog 4
Continuous static
stimulation
(Level set by
Intensity Dial)
Dog 2 / Dog 5
Continuous static
stimulation
(Level set by
Intensity Dial)
Dog 3 / Dog 6
Dog 1-3 /
Dog 4-6 6Tone
2
Continuous static
stimulation
(Level set by
Intensity Dial)
Dog 1 / Dog 4
Continuous static
stimulation
(Level set by
Intensity Dial)
Dog 2 / Dog 5
Continuous static
stimulation
(Level set by
Intensity Dial)
Dog 3 / Dog 6
Dog 1-3 /
Dog 4-6 6Vibration
3
Momentary static
stimulation
(Level set by
Intensity Dial)
Dog 1 / Dog 4
Momentary static
stimulation
(Level set by
Intensity Dial)
Dog 2 / Dog 5
Momentary static
stimulation
(Level set by
Intensity Dial)
Dog 3 / Dog 6
Dog 1-3 /
Dog 4-6 6Tone
4
Momentary static
stimulation
(Level set by
Intensity Dial)
Dog 1 / Dog 4
Momentary static
stimulation
(Level set by
Intensity Dial)
Dog 2 / Dog 5
Momentary static
stimulation
(Level set by
Intensity Dial)
Dog 3 / Dog 6
Dog 1-3 /
Dog 4-6 6Vibration
5
Continuous HIGH
static Stimulation
(Level set by
Intensity Dial)
Continuous LOW
static stimulation
(Level set by
Intensity Dial)
Tone
stimulation only Dog 1 / Dog 2 2 Vibration
6
Continuous HIGH
static stimulation
(Level set by
Intensity Dial)
Continuous LOW
static stimulation
(Level set by
Intensity Dial)
Vibration
stimulation only Dog 1 / Dog 2 2 Tone
7N/A N/A N/A N/A N/A N/A
V/T N/A N/A N/A N/A N/A N/A
NOTE: Modes 1, 2, 3, and 4 provide 7 levels of static stimulation, which correspond to the setting of the Intensity
Dial. Modes 5 and 6 provide more static stimulation “increments” to choose from – a total of 14 levels of static
stimulation. For example, in mode 5, with the Intensity Dial set at 2, the Lower Button provides level 3 static
stimulation and the Upper Button provides level 4 static stimulation.

17 SPORTDOG.COM
STEP::06
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER
To match the Collar Receiver to work with a new Remote Transmitter or to match a new Collar Receiver to work
with your existing Remote Transmitter:
Turn the Collar Receiver off.
Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 4-5 seconds. If the
On/Off Button is released too early, the Receiver Indicator Light will begin flashing as normal. If this occurs, start
over from 1.
After the Receiver Indicator Light has turned off, release the On/Off Button.
Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times.
You may need to hold both units 60 cm - 90 cm from each other before this occurs. Once the Receiver Indicator
Light has flashed 5 times, the Collar Receiver has been matched and will begin flashing as normal. If the Receiver
Indicator Light does not flash 5 times, start over from 1.
STEP::07
PROGRAM THE SYSTEM FOR TWODOG OPERATION
SportDOG®Collar Receivers can be set to respond to either the UP or DOWN Toggle Switch positions.
A SportDOG®Add-A-Dog®extra Collar Receiver must be purchased to train a second dog in two-dog mode. Please
refer to the last page for compatible Add-A-Dog®extra Collar Receivers for this system.
1. Program the Remote Transmitter to mode 1 or 2 in the Toggle Switch UP position or mode 5 or 6 in the Toggle
Down position (see STEP 05).
2. Flip the Toggle Switch to the UP position to program the first Collar Receiver.
3. Turn the Collar Receiver off.
A. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 4-5
seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin its normal
flashing. If this occurs, start over from A.
B. After the Receiver Indicator Light has turned off, release the On/Off Button.
C. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5
times. You may need to hold both units 60 cm - 90 cm from each other before this occurs. If the Receiver
Indicator Light does not flash 5 times, start over from A.
4. Program the second Collar Receiver using Athrough Dabove, but with the Toggle Switch in the
DOWN position.

18 SPORTDOG.COM
STEP::08
PROGRAM THE SYSTEM FOR THREEDOG TO SIXDOG OPERATION
SportDOG®Add-A-Dog®extra Collar Receivers must be purchased to train additional dogs. Please refer to the
last page for compatible Add-A-Dog®extra Collar Receivers for this system.
THREEDOG OPERATION
1. Program the Remote Transmitter to mode 3, 4, 5, or 6 in the Toggle Switch UP position (see STEP::05).
2. Flip the Toggle Switch to the UP position.
3. Program the first Collar Receiver.
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 4-5
seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin its normal
flashing. If this occurs, start over from A.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5
times. You may need to hold both units 60 cm - 90 cm from each other before this occurs. If the Receiver
Indicator Light does not flash 5 times, start over from A.
4. Program the second Collar Receiver using Athrough Dabove, but using the Lower Button in place of the
Upper Button.
5. Program the third Collar Receiver using Athrough Dabove, but using the Side Button in place of the
Upper Button.
Dog Arrow Colour
Dog 1 Orange
Dog 2 Red
Dog 3 Green
SIXDOG OPERATION
Program the Remote Transmitter to mode 1, 2, 3, or 4 in the Toggle Switch DOWN position (see STEP::05).
Repeat previous steps 3-5 with the Toggle Switch in the UP position for dogs 1, 2, and 3.
Repeat previous steps 3-5 with the Toggle Switch in the DOWN position for dogs 4, 5, and 6.
Dog Arrow Colour
Dog 1 Orange
Dog 2 Red
Dog 3 Green
Dog 4 Blue
Dog 5 Yellow
Dog 6 Grey

19 SPORTDOG.COM
STEP::09
CHANGE ID CODES
An ID Code is the signal identification between the Remote Transmitter and Collar Receiver. Each is programmed
in 1 of 4,000 ID Codes from the factory. In the rare event that a Remote Transmitter is sending a signal to more
than one Collar Receiver, you can change the Remote Transmitter’s ID Code to prevent this from happening. There
are 64 programmable ID Codes available.
TO MANUALLY PROGRAM THE REMOTE TRANSMITTER’S ID CODE
1. Turn the Intensity Dial to level 7, flip the Toggle Switch to the UP position, and then depress and release the
Mode Button on the back of the Remote Transmitter. This does not change the mode, so the current mode will
still be active after the ID change is complete.
2. Once the Mode Button is released, the Transmitter Indicator Light will illuminate green and stay on for
15 seconds.
3. While the green Indicator Light is on, turn the Intensity Dial to select the 1st digit of the ID and then press and
release the Side Button. The green Indicator Light will flash rapidly confirming selection.
4. Again, while the green Indicator Light is on, turn the Intensity Dial to select the 2nd digit of the ID and then
press and release the Side Button. The green Indicator Light will flash rapidly confirming selection. The 2nd
digit is optional and, if not desired, wait until the green Indicator Light turns off and refrain from pressing
the Side Button.
5. At the end of 15 seconds, or after the second press of the Side Button, the green Indicator Light will turn off
and the ID of the Remote Transmitter will be updated. At this point, the Remote Transmitter will be in the
same mode it was prior to setting the ID.
6. Upon changing the ID Code, you will need to match the Collar Receiver to the Remote Transmitter. See
STEP::06.
NOTE: If you press the Side Button only once (skipping STEP::04) the ID is still a two digit ID. The left digit is
defaulted to 1. For example, if you selected 6 in STEP::03 and pressed the button only once, the ID will be 16.
TO RETURN THE REMOTE TRANSMITTER TO THE FACTORY ID
1. Turn the Intensity Dial to level 7, flip the Toggle Switch to the UP position, and then depress and release the
Mode Button on the back of your Remote Transmitter. This does not change the mode, so the current mode
will still be active after the ID change is complete.
2. Do not press any buttons and wait until the green Transmitter Indicator Light turns off.
3. You will now need to match the Collar Receiver to the Remote Transmitter. See STEP::06.
NOTE: Removing the battery will also return the Remote Transmitter to the factory ID.
ACCESSORIES
To purchase additional accessories for your SportDOG®SportHunter™SD-1525E Multi-Dog Remote Trainer,
contact the Customer Care Centre or visit our website at www.sportdog.com to locate a retailer near you.