SportsArt Fitness A915 User manual

INDEPENDENT
CHEST PRESS
INDEPENDENT
CHEST PRESS
A915
OWNER'S MANUAL
ASSEMBLY INSTRUCTIONS

A. SAFETY INSTRUCTIONS
˙Read all cautions/warnings and obtain proper instruction on use of the machines
prior to using. Use appropriate positioning and controlled movements.
˙
˙
˙
˙
˙
˙
˙
˙
˙
˙
˙
˙
Assemble and operate the strength on a solid, level surface. Do not use outdoors
or near water.
Never allow children on or near the strength.
Make sure all fasteners are properly tightened for safety. DO NOT use the
strength if the unit is disassembled in any way.
Keep head, limbs, and fingers clear of all moving parts.
If at any time during exercise you feel faint, dizzy or experience pain, stop and
consult you physician.
DO NOT wear loose or dangling clothing while using the equipment. Keep away
from all moving parts.
Use care when mounting and dismounting the unit.
DO NOT use any accessories that aren't specifically recommended by the
manufacturer. These might cause injuries or cause the unit to fall.
Close supervision is necessary when this strength is used by, on, or near
adolescent, invalids, and disabled persons.
Use this strength only for its intended use as described in this manual.
Never operate this strength if it has been damaged in any way. If it is not working
properly, been dropped or damaged, contact your dealer. DO NOT attempt to fix a
broken or jammed machine. Notify floor staff.
Never drop or insert any object into any opening.
1

2
B. Introduction
Badge, front
Right grip
Back cushion
Left grip
Pedal push
rod assembly
Pedal push rod
assembly-right
Pedal push rod
assembly-left
Seat cushion and
seat cushion
adjustment handle
Foot pad
Side frame
Badge, rear
Front cover (A)
Foot pad
Support frame
Front cover (B)
Usage sticker
Rear cover
Cord
Stack fork
Hydraulic shock

1. One side
2. One support frame
3. One pedal push rod assy
4. One pedal push rod
5. One grip
6. Four hex socket head bolts M8 x P1.25 x L30, for the pedal push rod assembly and
pedal pushing rod ( )
7. Four spring washers, M8, for the pedal pushing rod assembly and pedal push rod
( )
8. Four flat washers D17 x d8.3 x t2 for foot rest
9. Two hex socket head bolts, M8 x P1.25 x L20, for the pedal push rod and grip
10. Two wave washer, (WN6203) for the pedal push rod and grip
11. One bearing washer for the grip
12. One washer for the pedal push rod
13. One double-end open wrench,17mm x 23mm
14. One double-end open wrench, 8mm x 17mm
15. One hex key wrench, M6
16. One hex key wrench, M5
17. User's manual
18. One double-end open wrench, 8mm x 10mm
19. One double-end open wrench, 12mm x 15mm
20
frame.
right and left
right and left
. One storage tray
3
C. List of Parts

D. STEP BY STEP INSTRUCTION:
1. Tighten the pedal pushing rod with screws as shown in Fig.1.
2. Tighten the grip with screws as shown in Fig.2.
4
Fig.2
Fig.1

3. Tighten the pedal push assembly and both left and right push rods together with
screws as shown in Fig. 3.
4. Assemble the belt and secure the screws tightly as shown in Fig. 4.
Fig.3
Fig.4
5

5. Please check the machine to see if both sides are level after assembly. Padding
either post with cardboard or wood plank to make both sides at the same level.
Then check the tightness of inserting the stack fork.
If you feel too tight or too loose when you insert the stack fork between the
weight stacks, it means the machine is not level so padding the post with
the stuff is required.
Note:
Fig.5
6

Fig.6
7
E. BELT ADJUSTMENT:
1. If the belt is too tight or too loose, first loosen nut A as shown then adjust nut B. If
the belt length is too long, adjust downward; if the belt length is too short, adjust
upward. Adjust the belt to the proper position, then tighten nut A.
2. The gap between nut A and B must be within 35mm(1.4"). If the gap still
exceeds the 35mm limit after the first step, please loosen the screws on C
and adjust the belt to the proper length. Tighten the screws and follow the
1st step again. (See Fig. 6)

Fig.7
8
F. HOW TO USE THE MINOR WEIGHT STACK
1. To adjust the minor weight stack, insert the upper pin to add 3.5Lbs/1.5kgs
or the lower pin to add 6.5Lbs/3kgs.
2. Pull the pin to release the weight. (See Fig. 7)
3.5Lbs/1.5kgs
6.5Lbs/3kgs

9
Applicable strength products include that these products have the frame as following
shape.
Step 1:
Remove the existing screw and washer from
tubing.
Step 2:
Place storage tray onto tubing and tighten with the.
screw and washer that you just removed from step.
G. STORAGE TRAY ASSEMBLY