SRAM SIDLUXE ISOSTRUT 2024+ User manual

SERVICE MANUAL
GEN.0000000007321 Rev A © 2023 SRAM, LLC
2024+
SIDLUXE ISOSTRUT

SAFETY FIRST!
We care about YOU. Please, always wear your safety glasses
and protective gloves when servicing RockShox products.
Protect yourself! Wear your safety gear!

TABLE OF CONTENTS
ROCKSHOX SERVICE..........................................................................................................................................................................................4
PART PREPARATION ......................................................................................................................................................................................................................................4
SERVICE PROCEDURES.................................................................................................................................................................................................................................4
MODEL CODE IDENTIFICATION .................................................................................................................................................................................................................5
WARRANTY AND TRADEMARK...................................................................................................................................................................................................................5
RECOMMENDED SERVICE INTERVALS....................................................................................................................................................................................................6
RECORD YOUR SETTINGS............................................................................................................................................................................................................................6
TORQUE VALUES.............................................................................................................................................................................................................................................6
PARTS, TOOLS, AND SUPPLIES  COMPREHENSIVE...........................................................................................................................................................................7
SIDLUXE ISOSTRUT SERVICE ...........................................................................................................................................................................8
PART IDENTIFICATION  2024+ A1 SIDLUXE ISOSTRUT............................................................................................................................9
DISCONNECT REMOTE CABLE........................................................................................................................................................................11
100 / 200 HOUR SERVICE
ISOSTRUT AIR CAN REMOVAL.................................................................................................................................................................................................................. 12
ISOSTRUT AIR CAN SERVICE .................................................................................................................................................................................................................... 17
100 HOUR SERVICE
SEALHEAD / AIR PISTON AND EYELET SERVICE.............................................................................................................................................................................. 24
BOTTOMLESS TOKENS OPTIONAL...................................................................................................................................................................................................... 27
200 HOUR SERVICE
DAMPER SERVICE......................................................................................................................................................................................................................................... 29
DAMPER REMOVAL...................................................................................................................................................................................................................................... 29
IFP REMOVAL ................................................................................................................................................................................................................................................. 32
DAMPER PISTON REMOVAL...................................................................................................................................................................................................................... 34
SEALHEAD / AIR PISTON REMOVAL AND SERVICE.......................................................................................................................................................................... 38
REMOTE SPRING SERVICE ........................................................................................................................................................................................................................ 43
REMOTE CABLE HOUSING STOP OPTIONAL...................................................................................................................................................................................50
REBOUND ADJUSTER SERVICE OPTIONAL....................................................................................................................................................................................... 51
SEALHEAD / AIR PISTON INSTALLATION............................................................................................................................................................................................. 55
SHOCK ASSEMBLY........................................................................................................................................................................................... 60
200 HOUR SERVICE
IFP INSTALLATION AND BLEED...............................................................................................................................................................................................................60
BOTTOMLESS TOKENS OPTIONAL...................................................................................................................................................................................................... 67
100 / 200 HOUR SERVICE
ISOSTRUT AIR CAN INSTALLATION ....................................................................................................................................................................................................... 69
REMOTE CABLE INSTALLATION AND CHECK LOCKOUT FUNCTION .....................................................................................................74

4
RockShox Service
RockShox Service
We recommend that you have your RockShox suspension serviced by a qualified bicycle mechanic. Servicing RockShox suspension requires
knowledge of suspension components, as well as the use of specialized tools and lubricants/fluids. Failure to follow the procedures outlined in this
service manual may cause damage to your component and void the warranty.
Visit www.sram.com/service for the latest RockShox Spare Parts Catalog and technical information. For order information, please contact your local
SRAM distributor or dealer.
Information contained in this publication is subject to change at any time without prior notice.
Your product's appearance may differ from the pictures contained in this publication.
For recycling and environmental compliance information, visit: www.sram.com/en/company/about/environmental-policy-and-recycling.
Part Preparation
Remove the component from the bicycle before service.
Disconnect and remove the remote cable or hydraulic hose from the fork or rear shock, if applicable. For additional information about RockShox
remotes, user manuals are available at www.sram.com/service.
Clean the exterior of the product with mild soap and water to avoid contamination of internal sealing part surfaces.
Service Procedures
The following procedures should be performed throughout service, unless otherwise specified.
Clean the part withClean the part with RockShox Suspension Cleaner or isopropyl alcohol andisopropyl alcohol and
a clean, lint-free shop towel. For hard to reach places (e.g. upper tube, lowera clean, lint-free shop towel. For hard to reach places (e.g. upper tube, lower
leg), wrap a clean, lint-free shop towel around a non-metallic dowel to cleanleg), wrap a clean, lint-free shop towel around a non-metallic dowel to clean
the inside.the inside.
Clean the sealing surface on the part and inspect it for scratches.Clean the sealing surface on the part and inspect it for scratches.
⚠WARNING  CRASH HAZARD
DO NOT use vinegar of any type to clean any part of a RockShox
suspension product. Vinegar can cause permanent damage to parts which
can, over time, result in product structural failure, serious injury, and possibly
death.
Replace the o-ring or seal with a new one from the service kit. Use yourReplace the o-ring or seal with a new one from the service kit. Use your
fingers or a pick to pierce and remove the old seal or o-ring.fingers or a pick to pierce and remove the old seal or o-ring.
Apply grease to the new seal or o-ring.Apply grease to the new seal or o-ring.
NOTICE
Do not scratch any sealing surfaces when servicing the product. Scratches
can cause leaks. Consult the RockShox Spare Parts Catalog to replace the
damaged part.
Use aluminum soft jaws when placing a part in a bench vise.Use aluminum soft jaws when placing a part in a bench vise.
Tighten the part with a torque wrench to the torque value listed in the red bar.Tighten the part with a torque wrench to the torque value listed in the red bar.
When using a crowfoot socket and torque wrench, install the crowfoot socketWhen using a crowfoot socket and torque wrench, install the crowfoot socket
at 90 degrees to the torque wrench.at 90 degrees to the torque wrench.
Specified torque value in N·m (in-lb)

5
Model Code Identification
Model Code Identification
Product model code and specification details can be identified with the serial number on the product. Model codes can be used to identify the
product type, series name, model name, and product version associated with the production model year. Product details can be used to identify spare
parts, service kit, and lubricant compatibility.
Model Code example: RS-SIDL-TKIS-A1
RS = Product Type - Rear Shock
SIDL = Platform/Series - SIDLuxe
TKIS = Model - Trek IsoStrut
A1 = Version - (A- first generation, 1- first iteration)
To identify the model code, locate the serial number on the product and enter it into the Search by Model Name or Serial Number field at
www.sram.com/service.
Warranty and Trademark
For SRAM Warranty information, visit: www.sram.com/en/service/warranty.
For SRAM Trademark information, visit: www.sram.com/en/company/legal/website-terms-of-use.

6
Recommended Service Intervals
Recommended Service Intervals
Regular service is required to keep your RockShox product working at peak performance. Follow this maintenance schedule and install the service
parts included in each service kit that corresponds with the Service Hours Interval recommendation below. For spare part kit contents and details,
refer to the RockShox Spare Parts Catalog at www.sram.com/service.
Service Hours Interval Maintenance Benefit
Every ride Clean dirt from shock damper body and
wiper seal
Extends wiper seal lifespan
Minimizes damage to shock damper body
Minimizes air can contamination
Every 100 Hours Perform air can service
Reduces friction
Restores small bump sensitivity
Every 200 Hours Perform damper and spring service
Extends suspension lifespan
Restores suspension performance
Record Your Settings
Use the table below to record your shock settings to return your shock to its pre-service settings. Record your service date to track service intervals.
Service Hours Interval Date of Service Air Pressure
Rebound setting - Count the
number of clicks while turning
the rebound adjuster fully coun-
terclockwise.
100
200
300
400
Torque Values
Part Tool Torque
Bolt (x4) - eyelet/mount to IsoStrut air can 4 mm hex bit socket 5 N•m (44 in-lb)
Bolt (x2) - remote cable housing stop 2.5 mm hex 1.3 N•m (10 in-lb)
IsoStrut air can seal sleeve to IsoStrut air can SIDLuxe IsoStrut Air Can Seal
Sleeve Socket Tool 4.5 N•m (40 in-lb)
Limit screw (rebound adjuster) to eyelet/mount 2 mm hex Tighten until limit screw flush
with eyelet/mount
Limit screw (remote spring preloader) to eyelet/mount 1.5 mm hex Tighten until limit screw flush
with eyelet/mount
Piston bolt to damper shaft
SIDLuxe Valve Cup and Piston
Bolt Socket Tool and 14 mm
socket
2.3 N•m (20 in-lb)
Piston valve cup to piston bolt
SIDLuxe Valve Cup and Piston
Bolt Socket Tool and 14 mm
socket
1.3 N•m (10 in-lb)
Sealhead / air piston to damper body 19 mm or adjustable crowfoot 28 N•m (250 in-lb)
Set screw (rebound adjuster detent) to eyelet/mount 2 mm hex Tighten until set screw flush with
eyelet/mount
Set screw (remote lockout pulley) to remote cam 1.5 mm hex Tighten until set screw stops
Set screw to sealhead / air piston bleed port 2 mm hex bit socket 0.56 N•m (5 in-lb)

7
Parts, Tools, and Supplies - Comprehensive
Parts, Tools, and Supplies - Comprehensive
Parts
• 2024+ (A1) SIDLuxe IsoStrut (Trek) - 100 or 200 Hour Service Kit
• 2024+ (A1) SIDLuxe IsoStrut (Trek) - Bottomless Tokens
(blue, quantity 2)
Safety and Protection Supplies
• Apron
• Clean, lint-free shop towels
• Nitrile gloves
• Oil pan
• Safety glasses
Lubricants and Fluids
• Loctite Threadlocker 242 (blue) or equivalentor equivalent
• Maxima PLUSH 7wt Suspension Oil (damper body)
• Maxima PLUSH Dynamic Suspension Lube Light (air can)
• RockShox Dynamic Seal Grease
• RockShox Suspension Cleaner or isopropyl alcohol
RockShox Tools
• RockShox SIDLuxe Air Valve Adapter Tool (blue) - (damper body)
• RockShox Rear Shock Vise Blocks 3-hole
• RockShox Schrader valve tool
• RockShox Shock Pump (600 psi max)
• SIDLuxe IFP Height Tool
• SIDLuxe Rear Shock Body Vise Block (23.8 mm)
• RockShox Rear Shock 10 mm Service Pin
(IsoStrut air can to vise - horizontal)
• SIDLuxe (A2) / IsoStrut Valve Cup and Piston Bolt Socket Tool
• SIDLuxe IsoStrut Air Can Seal Sleeve Socket Tool
(unthread/remove and thread/install from and into IsoStrut air can)
• SIDLuxe IsoStrut Air Can Seal Sleeve Removal Puck
(socket attachment -push sealhead out of IsoStrut Air Can)
Bicycle Tools
• Cable cutter
• Shock pump (600 psi max)
Common Tools
• Adjustable or open end crowfoot socket: 19 mm
• Adjustable or open end wrench: 19 mm
• Bearing punch / Gauge pin:
1/16" / 1.5 mm (OD) - sealhead stainless compression ball removal
• Bench vise with soft jaws - flat, slotted
• Hammer / Mallet
• Hex bit sockets: 2, 2.5, 4 mm
• Hex wrenches: 1.5, 2, 2.5, 4 mm
• Light
• Needle nose pliers
• Pick (metallic)
• Pick (non-metallic)
• Schrader valve tool
• Socket: 14 mm
• Socket extender (5/8")
• Socket wrench
• Torque wrench

8
SIDLuxe IsoStrut Service
SIDLuxe IsoStrut Service
Prior to servicing the rear shock, remove it from the bicycle frame according to the bicycle manufacturer's instructions.
Consult the frame manufacturer for any required spare parts, lubricants, tools, and procedures required to remove and install the rear shock from the
bicycle frame.
NOTICE
Use only 2024+ (A1) SIDLuxe IsoStrut spare parts and service kits with 2024+ (A1) SIDLuxe IsoStrut.
2020-2023 (A1) SIDLuxe and 2024+ (A2) SIDLuxe spare parts and service kits are NOT compatible with 2024+ (A1) SIDLuxe IsoStrut.
⚠WARNING
Before disassembly or service of any air system remove the air pressure from all air chambers and remove the air valve cores.
If your shock will not return to full extension, do not attempt to service or disassemble your shock. Attempting to service a shock that will not return
to full extension can cause severe and/or fatal injuries.
SAFETY INSTRUCTIONS
Always wear safety glasses and nitrile gloves when working with suspension fluid.
Place an oil pan on the floor underneath the area where you will be working on the shock.
NOTICE
When replacing seals and o-rings, use your fingers or a pick to remove
the seal or o-ring. Spray RockShox Suspension Cleaner on each part and
clean with a shop towel. Apply grease to the new seal or o-ring. Only use
RockShox Dynamic Seal Grease when servicing RockShox shocks.
Inspect each part for scratches. Do not scratch any sealing surfaces when
servicing your suspension. Scratches can cause leaks.

9
Part Identification - 2024+ (A1) SIDLuxe IsoStrut
Part Identification - 2024+ (A1) SIDLuxe IsoStrut
6
19
20
25
23
7
5
21
24
3
9
8
17
16
18
22
10
2
1
12
11
14
13
15
4
1. Air valve cap
2. Housing guide
3. Air valve
4. Eyelet/Mount
5. Cable pinch plate
6. Cable pinch bolt
7. Pulley - remote lockout
8. Rebound adjuster
9. Eyelet/Mount bolt (x4)
10. Frame mount (x2)
11. Bottomless Token (2 max)
12. Bottom out spacer
13. Washer
14. Bottom out bumper
15. Damper shaft
16. Sag o-ring
17. Bleed screw
18. Sealhead / Air Piston
19. IsoStrut Air Can
20. Negative Seal Sleeve (IsoStrut Air Can)
21. Damper body
22. Air valve (IFP)
23. Damper body eyelet/mount
24. Strut oil plug o-ring
25. Frame mount

10
Part Identification - 2024+ (A1) SIDLuxe IsoStrut
41
38
43
23
19
17
11
22
21
20
30
34
7
9
14
13
8
1
2
12
10
6
45
16
36
37
31
32
28
29
24
26
25
27
33
35
40
39
15
3
42
18
1. Air valve cap
2. Set screw - Preloader
3. Housing guide
4. Remote cam
5. Eyelet/Mount bolt (x4)
6. Inner cam bushing
7. Air valve
8. Outer cam bushing
9. Set screw - remote pulley / cam
10. Remote spring
11. Cable pinch plate
12. Preloader - remote spring
13. Cable pinch bolt
14. Pulley - remote lockout
15. Eyelet/Mount
16. Rebound adjuster
17. Rebound poker
18. Bottomless Token (2 max)
19. Bottom out spacer
20. Washer
21. Bottom out bumper
22. Damper shaft
23. IFP (internal floating piston)
24. Bleed screw
25. Compression ball - nylon (bleed port)
26. Sealhead / Air Piston
27. Quad ring seal
28. Sealhead backup ring
29. Sealhead backup ring
30. Damper body
31. Damper piston / shim assembly
32. Piston bolt
33. Air valve (IFP)
34. Eyelet/Mount - Damper body
35. Air valve cap
36. Valve slider
37. Valve cup
38. Negative Seal Sleeve (IsoStrut Air Can)
39. Frame mount (x2)
40. Sag o-ring
41. IsoStrut Air Can
42. Strut oil plug o-ring
43. Frame mount

11
Disconnect Remote Cable
Disconnect Remote Cable
Actuate the remote and set rear shock to the open unlocked position.Actuate the remote and set rear shock to the open unlocked position.
Remove the cable end cap.Remove the cable end cap.
Loosen the remote cable set screw.Loosen the remote cable set screw.
Remove the cable from the cable set screw plate.Remove the cable from the cable set screw plate.
Remove the cable housing from the remote cable housing guide.Remove the cable housing from the remote cable housing guide.
It is recommended, but not required, to install a new remote shifter cable if the cable is disconnected from the shock. If a new remote shifterIt is recommended, but not required, to install a new remote shifter cable if the cable is disconnected from the shock. If a new remote shifter
cable will be installed, refer to the appropriate RockShox remote user manual for cable removal and installation procedures.cable will be installed, refer to the appropriate RockShox remote user manual for cable removal and installation procedures.
Remove the shock from the frame. Consult the frame manufacturer for rear shock removal and installation procedures.Remove the shock from the frame. Consult the frame manufacturer for rear shock removal and installation procedures.
Needle Nose Pliers Needle Nose Pliers
1
2 mm
2
3
4
5

12
IsoStrut Air Can Removal
100 / 200 Hour Service IsoStrut Air Can Removal
Rotate the rebound adjuster counterclockwise until it stops, whileRotate the rebound adjuster counterclockwise until it stops, while
counting the number of detent clicks, to the full open (0) position.counting the number of detent clicks, to the full open (0) position.
Total rebound clicks - 10Total rebound clicks - 10
Record these numbersRecord these numbers to assist you with post-service set up.to assist you with post-service set up.
Remove the sag indicator o-ring.Remove the sag indicator o-ring.
Clamp the RockShox Rear Shock 10 mm Service Pin (SIDLuxe IsoStrutClamp the RockShox Rear Shock 10 mm Service Pin (SIDLuxe IsoStrut
Eyelet/Mount Vise Tool) into the RockShox Rear Shock Vise Blocks.Eyelet/Mount Vise Tool) into the RockShox Rear Shock Vise Blocks.
Slide the bottom out bumper onto the pin.Slide the bottom out bumper onto the pin.
Install the shock horizontally onto the 10 mm Service Pin through theInstall the shock horizontally onto the 10 mm Service Pin through the
eyelet/mount holes.eyelet/mount holes.
1
Rebound
2
3
Rear Shock 10 mm Service Pin Aluminum Vise Blocks
Rear Shock 10 mm Service Pin Aluminum Vise Blocks

13
IsoStrut Air Can Removal
RecordRecord your air pressure setting to assist with post-service set up.your air pressure setting to assist with post-service set up.
Thread a shock pump onto the air valve and check the pressure gauge.Thread a shock pump onto the air valve and check the pressure gauge.
Remove the air valve cap by hand. Use a small hex wrench to depressRemove the air valve cap by hand. Use a small hex wrench to depress
the Schrader valve and slowly release all air pressure from the air can.the Schrader valve and slowly release all air pressure from the air can.
⚠CAUTION
Do not disassemble a pressurized shock, this can cause the air can,
suspension fluid or debris to forcefully eject from the shock. Wear
safety glasses.
Slowly release the air from the air can to make sure the air is removed
from both chambers. Quickly releasing the air can trap air in the
negative chamber and cause the air can to forcefully eject from the
shock upon disassembly.
Use a RockShox Schrader valve tool to remove the valve core from theUse a RockShox Schrader valve tool to remove the valve core from the
valve body to make sure all air has been removed. Set the valve corevalve body to make sure all air has been removed. Set the valve core
aside.aside.
Loosen and unthread each eyelet/mount bolt (x4) 3 full rotationsLoosen and unthread each eyelet/mount bolt (x4) 3 full rotations
counterclockwise.counterclockwise.
Do not remove the bolts.Do not remove the bolts.
⚠CAUTION
Do not disassemble a pressurized shock, this can cause the air can,
suspension fluid or debris to forcefully eject from the shock. Wear
safety glasses.
Slowly release the air from the air can to make sure the air is removed
from both chambers. Quickly releasing the air can trap air in the
negative chamber and cause the air can to forcefully eject from the
shock upon disassembly.
4
Small hex wrench
RockShox Schrader valve tool
RockShox Schrader valve tool
5
4 mm 4 mm
4 mm 4 mm

14
IsoStrut Air Can Removal
Secure a cloth shop towel over the eyelet and the IsoStrut to preventSecure a cloth shop towel over the eyelet and the IsoStrut to prevent
the eyelet from ejecting from the IsoStrut.the eyelet from ejecting from the IsoStrut.
Unthread 3 of the bolts completely.Unthread 3 of the bolts completely.
⚠CAUTION
Do not remove all four bolts before this is done to avoid the eyelet/
mount ejecting suddenly from the IsoStrut air can in the event the
shock is not fully depressurized.
While holding the cloth towel firmly over the eyelet and strut, slowlyWhile holding the cloth towel firmly over the eyelet and strut, slowly
remove the final eyelet bolt until the eyelet suddenly separates fromremove the final eyelet bolt until the eyelet suddenly separates from
the strut. Remaining air pressure in the air spring chamber will force thethe strut. Remaining air pressure in the air spring chamber will force the
eyelet from the strut. An audible pop will be heard.eyelet from the strut. An audible pop will be heard.
⚠CAUTION
To avoid sudden ejection of the eyelet from the strut, hold the cloth
towel firmly while unthreading the final bolt.
Remove the bolt.Remove the bolt.
Slowly release pressure from the shop towel over the eyelet and allowSlowly release pressure from the shop towel over the eyelet and allow
the eyelet to further separate from the strut.the eyelet to further separate from the strut.
6
4 mm 4 mm
4 mm 4 mm
7
4 mm

15
IsoStrut Air Can Removal
Remove the shock from the Rear Shock Service Pin.Remove the shock from the Rear Shock Service Pin.
Pull the eyelet/mount/shaft/piston assembly and remove it from thePull the eyelet/mount/shaft/piston assembly and remove it from the
IsoStrut air can. Use your finger to protect the damper shaft andIsoStrut air can. Use your finger to protect the damper shaft and
damper body from scratching the edge of the strut air can.damper body from scratching the edge of the strut air can.
Set the eyelet/shaft/piston assembly aside.Set the eyelet/shaft/piston assembly aside.
⚠CAUTION  EYE HAZARD
Vacuum pressure will increase as you pull to remove the shock
assembly from the IsoStrut air can, and may suddenly release when
the sealhead clears the sealing surface inside the IsoStrut air can.
Wear safety glasses.
8

16
IsoStrut Air Can Removal
Install the IsoStrut air can back onto the Rear Shock Service PinInstall the IsoStrut air can back onto the Rear Shock Service Pin
horizontally.horizontally.
9
Rear Shock 10 mm Service Pin Aluminum Vise Blocks

17
IsoStrut Air Can Service
100 / 200 Hour Service IsoStrut Air Can Service
Install the IsoStrut Air Can Negative Seal Sleeve Socket Tool onto aInstall the IsoStrut Air Can Negative Seal Sleeve Socket Tool onto a
long socket extender and socket wrench.long socket extender and socket wrench.
Unthread (counterclockwise) the IsoStrut air can seal sleeve locatedUnthread (counterclockwise) the IsoStrut air can seal sleeve located
inside the IsoStrut air can. Unthread it until no resistance is felt. Theinside the IsoStrut air can. Unthread it until no resistance is felt. The
seal sleeve will remain inside the IsoStrut.seal sleeve will remain inside the IsoStrut.
Remove the tool. Remove the IsoStrut from the Rear Shock Service Pin.Remove the tool. Remove the IsoStrut from the Rear Shock Service Pin.
1
IsoStrut Air Can Negative Seal Sleeve
Socket Tool

18
IsoStrut Air Can Service
Insert the IsoStrut Air Can Seal Sleeve Removal Puck onto a longInsert the IsoStrut Air Can Seal Sleeve Removal Puck onto a long
5/8" socket extender. Insert the removal puck into the IsoStrut air can5/8" socket extender. Insert the removal puck into the IsoStrut air can
through the eyelet end until the edge of the puck tool stops against thethrough the eyelet end until the edge of the puck tool stops against the
seal sleeve.seal sleeve.
Push the seal sleeve out of the IsoStrut air can. Hold a shop towelPush the seal sleeve out of the IsoStrut air can. Hold a shop towel
around the end of the IsoStrut air can if excess grease and oil arearound the end of the IsoStrut air can if excess grease and oil are
present on the seal sleeve.present on the seal sleeve.
Remove and discard the outer o-ring and bushing.Remove and discard the outer o-ring and bushing.
2
IsoStrut Air Can Negative Seal Sleeve
Removal Puck and socket extender
3

19
IsoStrut Air Can Service
Remove and discard the inner wiper seal, quad ring seal, and backupRemove and discard the inner wiper seal, quad ring seal, and backup
ring.ring.
NOTICE
Do not scratch the quad ring seal groove. Scratches will cause air to
leak.
Clean the inside and outside of the seal sleeve, including the bushingClean the inside and outside of the seal sleeve, including the bushing
and seal grooves.and seal grooves.
4
Pick (non-metallic)
Pick (non-metallic)
Pick (non-metallic)
5
RockShox Suspension Cleaner

20
IsoStrut Air Can Service
Apply grease to a new quad ring seal and install it.Apply grease to a new quad ring seal and install it.
Install a new inner backup ring.Install a new inner backup ring.
Apply grease to a new wiper seal and install it.Apply grease to a new wiper seal and install it.
Install a new outer bushing.Install a new outer bushing.
Apply grease to a new outer o-ring and install it.Apply grease to a new outer o-ring and install it.
Set the seal sleeve assembly aside.Set the seal sleeve assembly aside.
6
RockShox Dynamic Seal Grease
RockShox Dynamic Seal Grease
7
RockShox Dynamic Seal Grease