ST STEVAL-IDB013V1 Administrator Guide

Figure 1. STEVAL-IDB013V1 circuit schematic (1 of 7)
CN2_3
CN3_2
CN3_1
CN1_10
CN1_4
CN1_2
CN1_3
CN1_5
CN4_4
CN3_4
CN3_6
CN3_5
CN3_3
CN3_7
CN3_8
CN1_1
CN1_9
CN4_1
CN4_2
CN4_3
CN4_5
CN4_6
CN1_6
CN1_7
CN1_8
CN2_1
CN2_5
CN2_8
CN2_2
CN2_4
CN2_6
CN2_7
STEVAL-IDB013V1
Connectors.SchDoc
DBG_USART_RX
DBG_USART_TX
DBG_BOOTLOADER DBG_SPI_SCK
DBG_SPI_MOSI
DBG_SPI_MISO
DBG_SPI_CS
DBG_SWCLK
DBG_SWDIO
DBG_RESET
USB_D_P
USB_D_N
DP-CON
Debugger
DAP_Link.SchDoc
BLE_NRST
PA 10_PUSH1
PA 2_SWDIO
PA 3_SWCLK
BLE_NRST
PB3_SPI_CLK
VBRD
PA 1_UART_TX
PB0_UART_RX
PA 8_SPI_MISO
PA 9_SPI_CS
PA 11_SPI_MOSI
PB5_PUSH2
PB4_LED_GREEN
PB2_LED_RED
PB15
PB14_INT1_LSM6D
PB7_LPS2X_SDA
PA 0_LPS2X_SCL
PB2_LED_RED
PB1_LED_RGB
PB1_LED_RGB
PB14_INT1_LSM6D
PB5_PUSH2
PB15
PA 1_UART_TX
PB0_UART_RX
PB3_SPI_CLK
PA 8_SPI_MISO
PA 11_SPI_MOSI
PA 9_SPI_CS
PA 10_PUSH1
PB6_CS_LSM6D
PB6_CS_LSM6D
PB4_LED_GREEN
PA 0_LPS2X_SCL
PB7_LPS2X_SDA
PB12
PB13
PB12
PB13
PA 2_SWDIO
PA 3_SWCLK
PB0_UART_RX
PA 1_UART_TX
PA 10_PUSH1
BLE_NRST
USB_D_P
USB_D_N
DP-CON
PA 9_SPI_CS
PB3_SPI_CLK
PA 8_SPI_MISO
PA 11_SPI_MOSI
PB1_LED_RGB
PB4_LED_GREEN
PB2_LED_RED
BLE_NRST
PA 10_PUSH1
PB5_PUSH2
PB14_INT1_LSM6D
PA 11_SPI_MOSI
PA 8_SPI_MISO
PB3_SPI_CLK
PB6_CS_LSM6D
PA 0_LPS2X_SCL
PB7_LPS2X_SDA
USB_D_P
USB_D_N
DP-CON
VBRD
USB_D_P
USB_D_N
DP-CON
USB connector
USB.SchDoc
PB6
PA0
PA 1_UART_TX
PB7
PB14
PA 11_SPI_MOSI
PB0_UART_RX
PA10
PB2
PB1
PA 3_SWCLK
PA 2_SWDIO
RSTN
PA 9_SPI_CS
PA 8_SPI_MISO PB5
PB3_SPI_CLK
PB4
PB15
PB13
PB12
BlueNRG-LPS
BlueNRG-LPS_CSP36.SchDoc
VBRD
BATT1 BATT2
CR2032
NF
VBRD
Power Options
VBAT
DL1
C15
1u_0402
R26
680
VLDO
USB_5V
NC 4
GND
2
EN
3
IN
1OUT 5
U2
LDK 120M33R
R28
10k
VLDO
VBAT
USB_5V
3
DD
1
GG
2
SS
Q3
3
DD
1
GG
2
SS
Q4
STR2P3LLH6
C16
1u_0402
1
2
JP_VBRD
Shunt Fitted
VBRDVBLUE
1
2
JP_VBLUE
Shunt Fitted
PUSH1
PUSH2
LED_RGB
PUSH_RSTN
LED_GREEN
LED_RED
Buttons & LEDs
Buttons_and_LEDs.SchDoc
LPS2X_SCL
LSM6D_SPI_MISO
LSM6D_SPI_CS
LSM6D_INT1
LSM6D_SPI_SCK
LPS2X_SDA
LSM6D_SPI_MOSI
Sensors
Sensors.SchDoc
Schematic diagrams
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 - September 2023
For further information contact your local STMicroelectronics sales office.
www.st.com

Figure 2. STEVAL-IDB013V1 circuit schematic (2 of 7)
PB7
E4
AT0_PB15
F3
PB0
D7
PB1
E6
AT2_PB13
D3
PB2
D5
PB3
C6
PB6
C4
VSSA
B7
RSTN B5
VFBSD B3
AT3_PB12
C2
AT1_PB14
E2
VDDA_VCAP A4
VDD2 A6
PA1
F7
VDDSD B1
VSSSD
A2
VLXSD D1
NC
F1
PB4
F5
PB5
G4
PA2
G6
VSSSX
H1
PA3
H5
PA0
H7
PA11
J4
PA9
J6
OSCIN K1
PA10
K5
VSSIO
K7
VDDRF L2
VSS_FTRX
L4
VSS_IFADC
L6
OSCOUT M1
RF1 M5
PA8
M7
U1
GND
VDDSD VDD2 VDDRF VCAP
Q2
XTAL_HS
Q1
XTAL_LS
PA0
PA1_UART_TX
PA2_SWDI O
PA3_SWCLK
PA8_SPI _MI SO
PA9_SPI _CS
PA10
PA11_SPI _MOSI
PB0_UART_RX
PB1
PB2
PB3_SPI _CLK
PB4
PB5
PB6
PB7
PB14
PB15
VDDSD VDDRF VDD2 VCAP
0201
100nF
C3
C0402
4.7uF
C2
VBLUE
VBLUE VBLUE
C0402
220nF
C1
C0402
1uF
C5
C0402
1uF
C4
C0201
6.8pF
C6
C0201
6.8pF
C7
VBLUE
22nH
L2
R0603
R1
0R
NF
L1
10uH
RSTN
0201
100nF
C9
C0402
4.7uF
C8
8.2pF
C0402
C13
8.2pF
C0402
C14
OUT_ANT 1 IN
3
GND4
2
GND1
4
GND2
5
GND3
6
X1
PB12PB13
GNDGND GNDGND
20pF C0201
C10
C11
1.2pF C12
NM
NF
L3
1.8nH
FEED
1
GND@1
2
GND@2
3
GND@3
4
ANT1
2450AT18D0100E
0R R3
GNDGND
J1
UFL
GNDGND
02010R
R2
Use the resistor to
connect either the
UFL or the antenna
Remove L1 and solder the resistor R1
for SMPS OFF configuration
0R
R61
NF
0R
R60
NF
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 2/11

Figure 3. STEVAL-IDB013V1 circuit schematic (3 of 7)
ARDUINO connectors
CN3_4
CN1_10
CN4_4
CN3_6
CN3_5
CN3_3
CN3_7
CN3_8
CN4_1
CN4_2
CN4_3
CN4_5
CN4_6
CN3_2
CN3_1
CN1_1
CN1_2
CN1_3
CN1_4
CN1_5
CN1_6
CN1_7
CN1_8
CN1_9
1
2
3
4
5
6
7
8
9
10
CN1
1
2
3
4
5
6
7
8
CN3
1
2
3
4
5
6
CN4
1
2
3
4
5
6
7
8
CN2
0_0402R6
0_0402R7
0_0402R9
0_0402R11
0_0402R13
0_0402R14
0_0402R15
0_0402R22
0_0402R24
0_0402R12
0_0402R10
0_0402R16
0_0402R18
0_0402R20
0_0402R21
0_0402R23
0_0402R25
R4 0_0402
R5 0_0402
R17 0_0402
R19 0_0402
V3V1
ROHS
TP1
GND
V4V2
TP3
GND
TP2
GND 10Y
Don't dispose
FCC Discalimer
CN2_1
CN2_8
CN2_2
CN2_3
CN2_4
CN2_5
CN2_6
CN2_7
Mounting holes Test points Logos
CE
UKCA
0_0402R8
ST
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 3/11

Figure 4. STEVAL-IDB013V1 circuit schematic (4 of 7)
USB_D_P
USB_D_N
D_P
D_N
DP-CON
100n_0402
C17
I/O11
1
GND
2
I/O21
3I/O22 4
VBUS 5
I/O12 6
U3
USBLC6-2SC6
USB Connector
D_P
D_N
USB_5V
CC1
3
SBU2
4
D-
5
D-
8
D+
6
D+
7
SBU1
10
CC2
9
VBUS 2
VBUS 11
SHIELD S1
SHIELD S2
SHIELD S3
SHIELD S4
SHIELD S5
SHIELD S6
GND 1
GND 12
CN5
DX07S016JA1R1500
USB_5V
R27
1.5K
USB_D_P
USB_D_N
DP- CON
5.1kR
R58
5.1kR
R59
GND
GND
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 4/11

Figure 5. STEVAL-IDB013V1 circuit schematic (5 of 7)
VDD_A
OSC_IN
OSC_OUT
1.5K
R34
20pF
C18
X2
XTAL_LS
1M
R37
1u_0402
C21
R35 680
DL2
100n_0402
C26
20pF
C19
DBG_BOOTLOADER
VBRDVBRDVBRD VBRD
VBRD BLE serial interface
100n_0402
C22
VBRD
VDD_1
VDD_2
VDD_3
VDD_4
VDD_A
BOOT0
OSC_IN
NRST
DP-CON
VDD_3
VDD_4
VDD_1VDD_2
OSC_OUT
DP-CON
JTCK
JTMS
USB_D_P
USB_D_N
VBRD
JTMS
DBG_SPI_CS
DBG_SPI_SCK
DBG_SPI_MISO
DBG_SPI_MOSI
PB14_SWDIO
PB13_SWCLK
PB1_RESET
DBG_RESET
DBG_SWCLK
DBG_SWDIO
DBG_USART_TX
DBG_USART_RX
100n_0402
C24
100n_0402
C25
100n_0402
C20
PA3_USART_RX
PA2_USART_TX
PA2_USART_TX
PA3_USART_RX
1
2
3
4
CN6
NF
JTCK
PA0-WKUP
14
PA1
15
PA2
16
PA3
17
PA4
20
PA5
21
PA6
22
PA7
23
PA8
41
PA9
42
PA10
43
PA11
44
PA12
45
PA13
46
PA14
49
PA15
50
PB0
26
PB1
27
PB2
28
PB3
55
PB4
56
PB5
57
PB6
58
PB7
59
PB8
61
PB9
62
PB10
29
PB11
30
PB12
33
PB13
34
PB14
35
PB15
36
PC0 8
PC1 9
PC2 10
PC3 11
PC4 24
PC5 25
PC6 37
PC7 38
PC8 39
PC9 40
PC10 51
PC11 52
PC12 53
PC13 2
PC14-OSC32_IN 3
PC15-OSC32_OUT 4
PD2 54
NRST 7
BOOT0 60
OSC_IN 5
OSC_OUT 6
U4A
STM32F103RCT6
VSS_1 31
VSS_2 47
VSS_3 63
VSS_4 18
VSSA 12
VDD_1
32
VDD_2
48
VDD_3
64
VDD_4
19
VDDA
13
VBAT
1
U4B
STM32F103RCT6
PB1_RESET
PB14_SWDIO
PB13_SWCLK
1 2
3 4
5 6
7 8
9 10
CN7
Header 5X2
R36
100
R31 0_0402
R33 0_0402
R30 0_0402
VLDO
2
3
1
Q5
JFET-P
USB_5V
R29
NM
NF
R32
10k
NRST
1u_0402
C23
USB_D_N
USB_D_P
DP-CON
Debugger SWD
Degugger and USB to serial
converter
Figure 6. STEVAL-IDB013V1 circuit schematic (6 of 7)
VDDIO
1
SCL
2
RES
3
SDA
4
SA0
5
CS 6
INT_DRDY 7
GND 8 GND 9 VDD 10
U7
100n_0402
C35
100n_0402
C34
SDO/SA0
1
SDx
2
SCx
3
INT1
4
VDDIO
5
GND
6
GND
7
SDA 14
SCL 13
CS 12
NC 11
OCS 10
INT2 9
VDD 8
U6
LSM6DSOX
LPS2X_SDA
LPS2X_SCL
VBRD
VBRD
VBRD
VBRD
VBRD
VBRD
VBRD
SENSORs
R49
0_0402
R50
0_0402
R51
0_0402
R52 0_0402
R54 0_0402
10k
R57
R56 0_0402
100n_0402
C33
4u7_0603
C30
100n_0402
C31
100n_0402
C32
10k
R55
R53 0_0402
LSM6D_SPI_CS
LSM6D_INT1
LSM6D_SPI_MISO
LSM6D_SPI_SCK
LSM6D_SPI_MOSI
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 5/11

Figure 7. STEVAL-IDB013V1 circuit schematic (7 of 7)
RED
DL3
PUSH2
PUSH1
100
R38
DL4
100k
R42
LED_GREEN
LED_RED
LED_RGB
PUSH2
PUSH_RSTN
VBRD
VBRD
VBRD
VBRD
VBRD
VBRD
BUTTONs
For multicolor LED solder 680 ohm resistor in R40 and R44
NM_0402
C27
NF
10n_0402
C28
PUSH1
RESET
R48
100
100
R39
100k
R43
10n_0402
C29
R47 680
GREENR40 0_0402
NF
R41 680
R45 680
R44 0_0402
NF
R46
100K
NF
LEDs
RED
GREEN
4
4
5
5
6
611
22
33
U5
AA A F3529LSEEZGKQBKS
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 6/11

Evaluation board license agreement
Important: All information on this document is subject to this Evaluation Board License Agreement.
By using this evaluation board or kit (together with all related software, firmware, components, and documentation
provided by ST, “Evaluation Board”), You (“You”) are agreeing to be bound by the terms and conditions of this
Evaluation Board License Agreement (“Agreement”). Do not use the Evaluation Board until You have read and
agreed to this Agreement. Your use of the Evaluation Board constitutes Your acceptance of this Agreement.
LICENSE
STMicroelectronics (“ST”) grants You the right to use the enclosed Evaluation Board offering limited features only
to evaluate and test ST products solely for Your evaluation and testing purposes in a research and development
setting. The Evaluation Board shall not be, in any case, directly or indirectly assembled as a part in any
production of Yours as it is solely developed to serve evaluation purposes and has no direct function and is not a
finished product. If software and/or firmware is accompanied by a separate end user license agreement (“EULA”),
then such software and/or firmware shall be governed by such EULA.
EVALUATION BOARD STATUS
The Evaluation Board offers limited features allowing You only to evaluate and test the ST products. The
Evaluation Board is not intended for consumer or household use. You are not authorized to use the Evaluation
Board in any production system, and it may not be offered for sale or lease, or sold, leased or otherwise
distributed for commercial purposes. If the Evaluation Board is incorporated in an evaluation system, the
evaluation system may be used by You solely for Your evaluation and testing purposes. Such evaluation system
may not be offered for sale or lease or sold, leased or otherwise distributed for commercial purposes and must be
accompanied by a conspicuous notice as follows: “This device is not, and may not be, offered for sale or lease, or
sold or leased or otherwise distributed for commercial purposes”.
OWNERSHIP AND COPYRIGHT
Title to the Evaluation Board remains with ST and/or its licensors. You may not remove any copyright or other
proprietary rights notices without prior written authorization from ST. You may make one copy of the software
and/or firmware of the Evaluation Board for back up or archival purposes provided that You reproduce and apply
to such copy any copyright or other proprietary rights notices included on or embedded in the software and/or
firmware. You agree to prevent any unauthorized copying in whole or in part of the Evaluation Board.
RESTRICTIONS AND WARNINGS
Before You handle or use the Evaluation Board, You must carefully review any related documentation provided by
ST. Such documentation may contain important warnings. You shall comply with all such warnings and other
instructions and employ reasonable safety precautions in using the Evaluation Board. Failure to do so may result
in death, personal injury, or property damage. If You have any questions regarding the safe usage of the
Evaluation Board, You should contact ST for guidance.
You may not sell, assign, sublicense, lease, rent or otherwise distribute the Evaluation Board for commercial
purposes, in whole or in part, or use Evaluation Board in a production system, with the exception that if You are
an authorized ST distributor, You may resell the Evaluation Board in compliance with the applicable terms and
conditions. Except as provided in this Agreement or as explicitly permitted in the documentation of the Evaluation
Board, You may not reproduce the Evaluation Board or modify,
reverse engineer, de-compile or disassemble its software and/or firmware, in whole or in part.
You shall not use the Evaluation Board in any safety critical or functional safety testing, including but not limited to
testing of life supporting, military or nuclear applications. ST expressly disclaims any responsibility for such usage
which shall be made at Your sole risk, even if ST has been informed in writing of such usage. Unless expressly
designated in writing by ST as suitable for use in testing automotive or aerospace applications, You shall not use
the Evaluation Board in such testing.
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 7/11

Notice applicable to Evaluation Boards according to European Regulation
For the European Regulation of the Evaluation Board, the applicable EU directives are considered, with a
particular attention to the Low Voltage Directive (LVD) 2014/35/EU, the Electromagnetic Compatibility (EMC)
Directive 2014/30/EU, and the Radio Equipment Directive (RED) 2014/53/EU. If the Evaluation Board is outside
the scope of the foregoing Directives, then the General Product Safety Directive (GPSD) 2001/95/EC and Council
Directive 93/68/EEC, amending Directive 73/23/EEC on electrical equipment designed for use within certain
voltage limits, are applicable.
The Evaluation Board meets the requirements of the Restriction of Hazardous Substances (RoHS 2 or RoHS
recast) Directive 2011/65/EU, Annex II, as amended by Directive 2015/863/EU.
Notice applicable to Evaluation Boards not FCC-Approved
This kit is designed to allow:
1. Product developers to evaluate electronic components, circuitry, or software associated with the kit to
determine whether to incorporate such items in a finished product and
2. Software developers to write software applications for use with the end product.
This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all
required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product
not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless
the assembled kit is designed to operate under part 15, part 18 or part 95 of 47 CFR, Chapter I (“FCC Rules”), the
operator of the kit must operate under the authority of an FCC license holder or must secure an experimental
authorization under part 5 of this chapter.
For Evaluation Boards annotated as FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 Compliant
•FCC Interference Statement for Class A Evaluation Boards: This equipment has been tested and found
to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
•FCC Interference Statement for Class B Evaluation Boards: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment.
WARRANTY
ST WARRANTS THAT IT HAS THE RIGHT TO PROVIDE THE EVALUATION BOARD TO YOU. THIS
WARRANTY IS PROVIDED BY ST IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, STATUTORY,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY AS TO MERCHANTABILITY, NON-INFRINGEMENT,
FITNESS FOR ANY PARTICULAR PURPOSE, OR UNINTERRUPTED OR ERROR-FREE OPERATION, ALL OF
WHICH ARE EXPRESSLY DISCLAIMED. THE EVALUATION BOARD IS PROVIDED “AS IS”.
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 8/11

YOU WARRANT TO ST THAT YOU WILL ENSURE THE EVALUATION BOARD IS USED ONLY BY
ELECTRONICS EXPERTS WHO UNDERSTAND THE DANGERS OF HANDLING AND USING SUCH ITEMS,
YOU ASSUME ALL RESPONSIBILITY AND LIABILITY FOR ANY IMPROPER OR UNSAFE HANDLING OR
USE OF THE EVALUATION BOARD BY YOU, YOUR EMPLOYEES, AFFILIATES, CONTRACTORS, AND
DESIGNEES.
LIMITATION OF LIABILITIES
IN NO EVENT SHALL ST BE LIABLE TO YOU, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE),
STRICT LIABILITY, OR ANY OTHER LEGAL THEORY, FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL,
INCIDENTAL, PUNITIVE, OR EXEMPLARY DAMAGES WITH RESPECT TO ANY MATTERS RELATING TO
THIS AGREEMENT, REGARDLESS OF WHETHER ST HAS BEEN ADVISED OF THE POSSIBILITY OF THE
SAME. IN NO EVENT SHALL ST’S LIABILITY ARISING OUT OF THIS AGREEMENT IN THE AGGREGATE
EXCEED THE AMOUNT PAID BY YOU UNDER THIS AGREEMENT FOR THE PURCHASE OF THE
EVALUATION BOARD, OR TEN UNITED STATES DOLLARS ($10.00) IF NO PURCHASE PRICE WAS PAID.
INDEMNIFICATION
You shall, at Your expense, defend ST and its Affiliates against a claim or action brought by a third party for
infringement or misappropriation of any patent, copyright, trade secret or other intellectual property right of a third
party to the extent resulting from (1) Your combination of the Evaluation Board with any other component, system,
software, or firmware, (2) Your modification of the Evaluation Board, or (3) Your use of the Evaluation Board in a
manner not permitted under this Agreement.
You shall indemnify ST and its Affiliates against and pay any resulting costs and damages finally awarded against
ST or its Affiliates or agreed to in any settlement, provided that You have sole control of the defense and
settlement of the claim or action, and ST cooperates in the defense and furnishes all related evidence under its
control at Your expense. ST will be entitled to participate in the defense of such claim or action and to employ
counsel at its own expense.
“Affiliates” means any corporation or other entity directly or indirectly controlled by, controlling or under common
control with the entity in question, for so long as such ownership exists. "Control" means the direct or indirect
beneficial ownership of more than fifty (50%) percent of the stock or other equity interests entitled to vote for the
election of directors or an equivalent governing body. Any such corporation or other legal entity shall be deemed
to be an Affiliate of such Party only as long as such Control exists.
TERMINATION
ST may terminate this Agreement without notice if You breach this Agreement. Upon termination, You shall
immediately destroy or return all copies of the software, firmware, and documentation of the Evaluation Board to
ST and certify in writing to ST that You have done so.
APPLICABLE LAW AND JURISDICTION
This Agreement shall be governed, construed and enforced in accordance with the laws of Switzerland, without
regard to its conflict of laws rules. The UN Convention on Contracts for the International Sale of Goods shall not
apply to this Agreement. In case of dispute and in the absence of an amicable settlement, the only competent
jurisdiction shall be the Courts of Geneva, Switzerland. Any breach of this Agreement by You may result in
irreparable damage to ST for which ST will not have an adequate remedy at law. Accordingly, in addition to any
other remedies and damages available, You acknowledge and agree that ST may immediately seek enforcement
of this Agreement in any jurisdiction by means of specific performance or injunction, without any requirement to
post a bond or other security.
SEVERABILITY
If any provision of this agreement is or becomes, at any time or for any reason, unenforceable or invalid, no other
provision of this agreement shall be affected thereby, and the remaining provisions of this agreement shall
continue with the same force and effect as if such unenforceable or invalid provisions had not been inserted in
this Agreement. In addition, any unenforceable or invalid provision shall be deemed replaced by a provision that is
valid and enforceable and that comes closest to expressing the intention of the unenforceable or invalid provision.
WAIVER
The waiver by either party of any breach of any provision of this Agreement shall not operate or be construed as a
waiver of any other or a subsequent breach of the same or a different provision.
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 9/11

RELATIONSHIP OF THE PARTIES
Nothing in this Agreement shall create, or be deemed to create, any joint venture, partnership, principal-agent,
employer-employee or other relationship between the Parties, except that of independent contractors. Neither
Party has the authority or power to bind, to contract in the name of, or to create a liability for the other in any way
or for any purpose.
SURVIVAL
Any provision of this Agreement which imposes an obligation after termination of this Agreement shall survive the
termination of this Agreement.
SECTION HEADINGS
Section headings are inserted for convenience only and shall not be used to interpret this Agreement.
WASTE AND RECYCLING
The Evaluation Board is not to be disposed of as urban waste. At the end of its life cycle, differentiated
waste collection must be followed. Consult the local authorities for more information on the proper disposal
channels. It is mandatory to separately collect the Evaluation Board and make sure it is delivered it to the
appropriate waste management and recycling centers.
As of 15 August 2018, in all the countries belonging to the European Union, the Evaluation Board is subject to the
WEEE Directive 2012/19/EU requirement; therefore, it is forbidden to dispose of the Evaluation Board as
undifferentiated waste or with other domestic wastes. Consult the local authorities for more information on the
proper recycling centers.
Disposing of the Evaluation Board incorrectly may cause damage to the environment and may be subject to fines
based on specific countries’ rules.
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 10/11

IMPORTANT NOTICE – READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other product or service names
are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2023 STMicroelectronics – All rights reserved
STEVAL-IDB013V1
STEVAL-IDB013V1 - Rev 1 page 11/11