Stages cycling SOLO User manual

SOLO TABLET REMOVAL/
INSTALLATION INSTRUCTIONS

Required Tools
#1 Phillips Screw Driver

Tablet Removal

1. Unplug the power cable from the bike.

2. Remove the (4) Phillips-head screws from the rear of the tablet. Lay the tablet over and pull
out approximately 1 to 2 inches of the power cable from the bracket to give you room to lay
the tablet over on top of phone holder.
Note: Keep one hand on the tablet to make sure the tablet is secure while detaching. Make
sure not to lose the screws.

3. Remove the three (3) small screws from the port cover.
Note: Ensure tablet is secure while removing screws, to keep tablet from falling. Make sure not
to lose screws.

4. Lift and remove port cover from the rear of the tablet.
Note: Ensure tablet is secure while removing cover, to keep tablet from falling.

5. Unplug the power cable, USB, and headphone cable from the bottom of the tablet.
Power
Cable
Headphone
Cable USB
Cable

6. Remove the power cable completely from the tablet, then remove the tablet from bike.
Note: Ensure tablet is secure while unplugging power cable, to keep tablet from falling.Power
cable will stay with new bike and will be used for new tablet.
Power
Cable

7. Reinstall the port cover and all the removed screws back onto the old tablet.

Tablet Replacement

1. Unbox the new tablet and repackage the old tablet into the package in the same manner
that the new tablet came out and using the materials from new tablet. Once packaged,
tape up the box and affix the return label (provided) and ship back.
Note: If there is no return label enclosed, please contact [e-mail]
or call 800-717-8076.

2. Remove the three (3) screws from the port cover and then lift and remove the port cover.
Also remove the four (4) Phillips screws from the back of new tablet.
Note: If your new tablet has a power cord attached to it, unplug it from the tablet prior to
proceeding to the next step. Make sure not to lose screws.

3. Unplug the USB and the headphone cables and then route the power cable from the bike
under the USB and headphone cables and plug in. Then, plug in the USB and headphone
cables over the power cable on the new tablet.
Note: Ensure tablet is secure while plugging in cables, to keep tablet from falling. Please be
careful plugging in cables, not to damage ports as cables are being inserted.
Power
Cable
Headphone
Cable
USB
Cable

4. Prior to installing port cover, ensure that the in-line filter on the power cable is tucked into
the tablet and the power cable is feed through the small cut out on the bottom cover.
Cut Out
In Line
Filter

5. Reinstall the port cover onto the tablet with the three (3) small screws and make sure it is
flush with the back of the tablet.

6. Lift up tablet and push the extended power cable back into the tablet bracket (1 to 2 inches
pulled out during tablet removal), then reattach the new tablet to the bracket using the four (4)
Phillips-head screws.

7. Once the new tablet is reinstalled, plug the power cord back into bike.

8. Once powered up the “Stages Solo” screen will appear and then the “Welcome to Stages Solo”
screen will appear on the tablet. After the “Welcome to Stages Solo” screen appears, press the
“Device Set Up” button.

9. The next screen will be the “Connect to power meter” screen. Prior to selecting a power
meter you will need to locate the ANT ID on the power meter. It is a 5 digit number on the
side of the power meter. Once located pedal the bike to wake up the power meter. Then
select the matching ANT ID on the tablet screen. Once connected press the “Next” button.
Note: If your power meter’s ANT ID does not come up on tablet. Use your Phillips screw driver
and open the battery door, take out the batteries in the power meter and flip the batteries
upside down. Close the battery door and hold down battery door for 5 seconds. Then, reinstall
the batteries correctly and tighten battery door. This should allow the ANT ID to be found.