Stanley SCL User manual

Please read these instructions before operating the product
SCL / SCL-D
2 - Beam Self-Levelling Cross Line Laser
77-320 / 77-321
Self-Levelling
(SCL-D with additional 2 - Beam Spot)
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
HR
LT
TR

277-320 / 77-321
(-)
(+)
9
(-)
(+)
(-)
(+)
A
B
C
1
8
2
3
4
6
7
5
SCL
B1SCL-D
B2
8

3
77-320 / 77-321
E
D
F
16
F1F2
6
10
11
1/45/8
E1E2

477-320 / 77-321
J
G
H
H1H2
J1J2

5
77-320 / 77-321
K
D1
D1
2
P1P2
D1
D1
2
P1
D2
P3
P4
P1 P1
P3
P2 P2
K1K2
K3K4
K5
D2
P4
P2
D4
P3
P1D3

677-320 / 77-321
L
L1L2
L4
P1
D1
D1
2
D1
2
L3
P1
D1
D1
2
D1
2
P2
P1
D1
D1
2
D1
2
P3
P2
P2D2
P1
P3

7
77-320 / 77-321
M
P1
L
D1
2 x L
P2
P3
D2
P1
P4
M3
M1M2
P1
L
D1
2 x L
P2
P3
P4
N
N1N2
N3
D1
D2
P1
P2
D1
D2
P1
P2
P3
D3
P3
P1

877-320 / 77-321
Contents
• Safety
• Product Overview
• Keypad, Modes, and LED
• Batteries and Power
• Set Up
• Operation
• Applications
• Accuracy Check and Calibration
• Specifications
User Safety
WARNING:
• Carefully read the Safety Instructions and
Product Manual before using this product.
The person responsible for the instrument must
ensure that all users understand and adhere to
these instructions.
CAUTION:
• While the laser tool is in operation, be careful
not to expose your eyes to the emitting laser
beam (red light source). Exposure to a laser
beam for an extended time may be hazardous
to your eyes.
CAUTION:
• Glasses may be supplied in some of the laser
tool kits. These are NOT certified safety glasses.
These glasses are ONLY used to enhance the
visibility of the beam in brighter environments or
at greater distances from laser source.
Retain all sections of the manual for future reference.
WARNING:
• The following label samples are placed on
your laser tool to inform of the laser class for
your convenience and safety. Please reference
the Product Manual for the specifics on a
particular product model.
EN 60825-1
LASER RADIATION - DO NOT
STARE INTO THE BEAM OR VIEW
DIRECTLY WITH
OPTICAL INSTRUMENTS
CLASS 2 LASER PRODUCT
Max Output ≤ 1 mW @ 630 - 670 nm
Product Overview
Figure A - Laser Tool
1. 1/4 - 20 Threaded Mount
2. Window for Vertical Beam Laser
3. Window for Horizontal Beam Laser
4. Pendulum / Transport Lock
5. Window for Up Beam Laser (SCL-D only)
6. 5/8 - 11 Threaded Mount
Window for Down Beam Laser (SCL-D only)
7. Keypad
8. Battery Cover
Figure B - Keypad Configurations
Figure C - Laser Tool Battery Location
8. Battery Cover
9. Batteries - 3 x “AA”
Figure D - Threaded Mounts
1. 1/4 - 20 Threaded Mount
6. 5/8 - 11 Threaded Mount
Figure E - Laser Tool on Tripod / Attachment
10. Center Screw Thread
11. Center Screw Knob
GB

9
77-320 / 77-321
Figure F - Pendulum / Transport Lock Positions
Figure G - Laser Modes
Figure H - Pulse Mode
Figure J - Manual Mode
Figure K - Level Beam Accuracy
Figure L - Horizontal Beam Accuracy
Figure M - Vertical Beam Accuracy
Figure N - Up and Down Beam Accuracy
Keypad, Modes, and LED
Keypads (See figure B)
Power ON / OFF / Mode Key
Pulse Mode ON / OFF Key
Modes (See figure G)
Available Modes (SCL)
• Horizontal Line
• Vertical Line
• Horizontal Line and Vertical Line (Cross)
• All beams OFF
Available Modes (SCL-D)
• Horizontal Line
• Vertical Line
• Horizontal Line and Vertical Line (Cross)
• Up and Down Dot Beam
• All Line and Dot
• All beams OFF
LEDs (See figure B)
Power LED - Solid GREEN
• Power is ON
Power LED - Blinking RED
• Low Battery
Power LED - Solid RED
• Battery Needs Recharging
Lock LED - Solid RED
• Pendulum lock is ON
• Self-Levelling is OFF
Lock LED - Blinking RED
• Out of Compensation Range
Pulse LED - Solid GREEN
• Pulse Mode is ON
(Can be used with Detector)
Batteries and Power
Battery Installation / Removal
(See figure C)
Laser Tool
• Turn laser tool to back. Open battery compartment cover
by pressing and sliding out.
• Install / Remove batteries. Orient batteries correctly
when placing into laser tool.
• Close and lock battery compartment cover by sliding in
until securely closed.
WARNING:
• Pay close attention to the battery holder’s (+)
and (-) markings for proper battery insertion.
Batteries must be of same type and capacity. Do
not use a combination of batteries with different
capacities remaining.

10 77-320 / 77-321
Set Up
Mounting on Accessories
Tripod / Accessory Mount (See figure E)
• Position a tripod / accessory in a place where it will not
be easily disturbed and near the central location of the
area to be measured.
• Set up the tripod / accessory as required. Adjust
positioning to be sure tripod head / accessory mounting
base is near horizontal.
• Remove the leg attachment from the laser tool for easier
mounting.
• Mount the laser tool to the tripod / accessory by pushing
up the center screw and tighten (Accessories with either
1/4 or 5/8 thread screw can be used).
CAUTION:
• Do not leave the laser tool unattended on an
accessory without fully tightening the center
screw. Failing to do so may lead to the laser tool
falling and sustaining possible damage.
NOTE:
• It is best practice to always support laser tool with
one hand when placing or removing laser tool from an
accessory.
• If positioning over a target, partially tighten the center
screw, align laser tool, and then fully tighten.
Operation
NOTE:
• See LED Descriptions for indications during operation.
• Before operating the laser tool always be sure to check the
laser tool for accuracy.
• In Manual Mode, Self-Levelling is OFF. The accuracy of the
beam is not guaranteed to be level.
• Laser tool will indicate when it is out of compensation
range. Reference LED Descriptions. Reposition laser tool
to be closer to level.
• When not in use, please be sure to power OFF the laser
tool and place the pendulum lock in the locked position.
Power
• Press to turn laser tool ON.
• To turn laser tool OFF, repeatedly press until the
OFF mode is selected OR press and hold for ≥ 3
seconds to turn laser tool OFF while in any mode.
Mode
• Press repeatedly to cycle through the available
modes.
Self-Levelling / Manual Mode
(See Figures Fand J)
• The pendulum lock on the laser tool needs to be
switched to the unlocked position to enable self-
levelling.
• The laser tool can be used with the pendulum lock in
the locked position when it is required to position the
laser tool at various angles to project non-level straight
lines or points.
Pulse Mode (See Figure H)
• When laser tool is ON, press to turn ON / OFF
pulse mode.
• Pulse mode allows use with laser detector.
Applications
Plumb / Point Transfer
• Using the vertical laser beam, establish a vertical reference
plane.
• Position the desired object(s) until they are aligned with the
vertical reference plane to ensure object(s) are plumb.
(SCL-D only):
• Establish 2 reference points that need to be plumb.
• Align either the down laser beam or the up laser beam to a
set reference point.
• The opposing laser beam(s) will be projecting a point which
is plumb.
• Position the desired object until the laser beam is aligned
with the second reference point that needs to be plumb
with the set reference point.