Stanley T15h User manual

T15h Temperature
& Humidity Tag
Deployment & User Guide
0981-697-000 REV A
Published: 2021/01/27 (updated 2021/02/07)

WARNING!
To comply with FCC and IC RF exposure compliance requirements, the device should be located at a distance ofat
least 20 cm from all persons during normal operation. The antennas used for this product must not be co-located
or operated in conjunction with any other antenna or transmitter.
Le dispositif doit être placé à une distance d'au moins 20 cm à partir de toutes les personnes
au cours de son fonctionnement normal. Les antennes utilisées pour ce produit ne doivent pas
être situés ou exploités conjointement avec une autre antenne ou transmetteur.
Disclaimer
The information and know-how included in this document are the exclusive property of STANLEY Healthcare and are
intended for the use of the addressee or the user alone. The addressees shall not forward to another their right of using
the information, know-how or document forwarded herewith, in whole or in part in all matters relating or stemming from or
involved therein, whether for consideration or without consideration, and shall not permit any third party to utilize the
information, know-how or the documents forwarde
consent in advance and in writing. Any distribution, advertisement, copying or duplication in any form whatsoever is
absolutely prohibited. The Company reserves the right to sue the addressee, user and/or any one on their behalves, as
well as third parties, in respect to breaching its rights pertaining to the intellectual rights in particular andits rights of
whatever kind or type in the information, know-how or the documents forwarded by them herewith in general, whether by
act or by omission.
This document is confidential and proprietary to STANLEY Healthcare and is not to be distributed to any persons other
than licensed AeroScout Visibility System users or other persons appointed in writing by STANLEY Healthcare.
Trademark Acknowledgements
AeroScout is a trademark of Stanley Black & Decker, Inc. or its affiliates. Other brand products and service names are
trademarks or registered trademarks of their respective holders. Below is a partial listing of other trademarks or registered
trademarks referenced herein:
Sun, Sun Microsystems, the Sun Logo, Java, JREand all other Sun trademarks, logos, product names, service names,
program names and slogans that are referred to or displayedin this document are trademarks or registered trademarks of
Sun Microsystems, Inc. in the UnitedStates and other countries.
This product includes software developed by the Apache Software Foundation (http://www.apache.org/).
This product includes code licensed from RSA Data Security.
trademarks of Skype Limited or other related companies.
Esper is a trademark of EsperTech, Inc.
Jboss is a trademark of Red Hat Middleware, LLC.
Oracle 10G is a registered trademark of Oracle Corporation and/or its affiliates.
MS SQL Server is a registered trademark of Microsoft Corporation in the UnitedStates and/or other countries.
JasperSoft, the JasperSoft Logo, JasperReports, the JasperReports logo, JasperIntelligence, JasperDecisions,
JasperAnalysis, Scope Center, Scope Designer, and JasperServer are trademarks or registeredtrademarks of JasperSoft,
Inc. in the United States and other countries.
iCloud Drive, iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App
Store®is a service mark of Apple Inc., registered in the U.S. andother countries.
©2021 STANLEY Healthcare. All rights reserved.
Doc: 0981-697-000 REV A. Updated: 2021/02/07. KB Article: 12300.

T15h Tag Deployment & User Guide
3
Introduction........................................................................................7
What’s in the Box? .......................................................................................................................8
Pre-Requisites...............................................................................................................................8
Minimum Requirements................................................................................................................................8
Reference Documentation.........................................................................................................8
T15h Features.....................................................................................9
T15h Tag Key Features..............................................................................................................9
Tag Descriptions............................................................................... 11
Screen Values..............................................................................................................................12
Status Icons...................................................................................................................................13
Tag Functions ...................................................................................14
Accessing and Using the Tag’s Menu Options ..................................................................14
Tag Menu Options.........................................................................................................................................14
Activating and Configuring the Tag ............................................ 15
Tag Activation...............................................................................................................................15
Tag Configuration........................................................................................................................15
Enabling BLE Tag Functions.....................................................................................................................15
Enabling Secured Tag Communication with MobileView..............................................................17
The STANLEY T15h Tag Certificate...................................................................................................18
Certificate Format.......................................................................................................................................18
MobileView Server Certificates.............................................................................................................18
MobileView Server Host Name.............................................................................................................18
Certificate Definitions................................................................................................................................18
Exporting a Secured Certificate from MobileView.........................................................................19
Loading a Secured Certificate to the Tags......................................................................................22
Configuring Tags...........................................................................................................................................24
About UD and BD Deployments.............................................................................................................26
UD (Unidirectional) Deployment Configuration................................................................................27
BD (Bidirectional) Deployment Configuration...................................................................................30
Saving, Exporting, Importing, and Loading Tag Configurations................................................35
Saving Configurations..............................................................................................................................35
Exporting a Configuration.......................................................................................................................35

T15h Tag Deployment & User Guide
4
Importing and Loading a Tag’s Configuration................................................................................36
Viewing a Tag’s Current Configuration................................................................................................37
Editing Transmission and Sensor Settings (UD Deployments).................................................38
Editing Transmission and Wireless Settings (BD Deployments)...............................................41
Secure Unidirectional Message Transmission.................................................................................44
Temperature & Humidity Sensor Deployments........................45
Configuring MobileView............................................................................................................45
Creating / Editing a Category...................................................................................................................45
Setting Thresholds on a Category Level..........................................................................................45
Setting Thresholds on an Asset Level:.............................................................................................47
Configuring Events.......................................................................................................................................47
Temperature Event...................................................................................................................................47
Humidity Event............................................................................................................................................49
Battery Level Event....................................................................................................................................51
Out of Sight Event.......................................................................................................................................51
External Power Event (Optional).........................................................................................................52
Sensor Tag Error Event..........................................................................................................................52
Mounting and Connecting.............................................................53
Connecting the Power Adapter..............................................................................................53
Mounting the Tag........................................................................................................................54
Mounting with Double-Sided Tape.........................................................................................................54
Placing the Tag in the Cradle...................................................................................................................55
Removing the Tag from the Cradle.......................................................................................................55
Using the T15h Tag.........................................................................56
Muting/Unmuting the Tag Button Sound.............................................................................56
Changing the Temperature Conversion..............................................................................56
Muting an Alarm..........................................................................................................................56
Show/Hide Thresholds..............................................................................................................57
Changing the Display Language............................................................................................57
Performing an Audit –Manual Inspection...........................................................................58
Viewing Min/Max Values..........................................................................................................58
Performing a Manual Sync with MobileView......................................................................59
Viewing Warnings......................................................................................................................60
Warning Messages........................................................................................................................................61
Updating Tag Firmware............................................................................................................62

T15h Tag Deployment & User Guide
5
Swapping or Removing Inactive Tags in MobileView.....................................................62
LED and Buzzer Indications....................................................................................................63
MobileView Battery & Power Indications.............................................................................64
Replacing the Batteries.............................................................................................................64
Reports..............................................................................................65
Battery Level Report..................................................................................................................65
Audit Report (and offline data)...............................................................................................66
Temperature History Report....................................................................................................66
Humidity History Report............................................................................................................67
Condition Monitoring Audit (and offline data).....................................................................67
Sensor Detailed Report............................................................................................................67
Sensor Summary Report...........................................................................................................71
Tag Models & Accessories............................................................74
Approved Barcode Readers..........................................................75
Tag Specifications...........................................................................76
Environmental Specifications................................................................................................................76
Monitoring Temperature & Humidity Ranges.................................................................................76
Tag Memory.................................................................................................................................................76
Physical and Mechanical........................................................................................................................76
Connectors...................................................................................................................................................76
Electrical........................................................................................................................................................76
Display............................................................................................................................................................76
Audio and Visual Indications.................................................................................................................76
Radio...............................................................................................................................................................76
Range..............................................................................................................................................................77
Communication............................................................................................................................................77
Wi-Fi Security Modes................................................................................................................................77
Logging Rates..............................................................................................................................................77
Certification....................................................................................................................................................77
Regulatory Compliance and Warranty........................................78
FCC.................................................................................................................................................78
Suppliers Declaration of Conformity.....................................................................................78
Canada—Innovation, Science, and Economic Development Canada......................78
RoHS..............................................................................................................................................79

T15h Tag Deployment & User Guide
6
CE Conformance........................................................................................................................79
Warranty........................................................................................................................................80

T15h Tag Deployment & User Guide
7
The T15h Tag adds advanced temperature & humidity monitoring capabilities to
market-leading family of Wi-Fi tags, making it ideal for
use in all hospital departments.
Ambient Temperature and Humidity Monitoring
The tag is equipped with internal sensors that constantly monitor ambient
temperature and humidity, of mission-critical locations such as operating rooms.
The T15h Tag can be supplied with a NIST traceable Certificate of Calibration
compliant to ISO 17025:2005.
The T15h Tag provides local audible and visual alerts and works with STANLEY
-time alerting and reporting for
temperature and humidity monitoring solutions.

T15h Tag Deployment & User Guide
8
The T15h Tag is supplied with the following components:
T15h Tag
2 AA Batteries
Tag Mounting Bracket
Screws & Double-sided tape
Pre-Requisites
Minimum Requirements
Components
Version
MobileView
5.5 and above
Engine
5.5 and above
Deployment
Manager (DM)
Version 5.0.1 and above
Deployment Manager App Requirements:
iOS: 9.x, 10.x, 11.x, 12.x, 13.x and 14.x
Supported Devices:
iPhone 5S and above
iPad Pro, Mini, Air
iPad 3rd generation and above
iPod touch 5th generation and above
Reference Documentation
The following articles can be accessed by logging into the STANLEY
Healthcare Support Community site at the following URL:
www.stanleyhealthcare.com/support.
KB
Document Name
12299
T15h Temperature & Humidity Tag Data Sheet
12301
T15h Tag Release Notes
12300
T15h Tag Deployment & User Guide (This doc)
See KB
Refer to any MobileView Administrator Guide from 5.5 and above
9758
Deployment Manager Setup & User Guide

T15h Tag Deployment & User Guide
9
T15h Tag Key Features
Large Display and Push Button Functionality
and maximum values measured since the last audit, battery and power status,
alarm indications, and warnings. The buttons are used to navigate and select
single-press.
Audio and Visual Indications
T15h Tags include a buzzer with 4 different distinct sounds and 3 LEDs for
status indications, such as tag activation, alerts, and low battery.
Wi-Fi & Cyber Security
The tag supports 802.1x Enterprise security networks with a PEAP-MSCHAPv2
protocol. Additionally, they support an HTTPS connection with MobileView
Servers using the TLS1.2 protocol. This allows a MobileView Server
authentication using pre-installed X.509 certificates.
Bluetooth Low Energy (BLE) Communication
T15h Tags use BLE technology to communicate with the Deployment Manager
(DM) app for device configuration and setup.
Beaconing and Bidirectional (BD) Communication
The tags utilize lightweight beaconing communication (for standard messages)
and Bidirectional Wi-Fi communication with full network association and
authentication. This unique combination provides a flexible and scalable
solution for advanced applications. The tags can operate with one network
SSID in a secure or non-secure mode and can store up to two application
server connections. The T15h Tags also support both static IP configuration
and DHCP.
Battery and External Power Options
The tags are powered by 2 AA batteries, which is the recommended power
source, and an optional power adaptor that can be used to save battery life.
Battery levels are constantly monitored by the device and MobileView. The tag
will use external power whenever available (batteries are recommended as a
backup if external power is used).

T15h Tag Deployment & User Guide
10
Internal Temperature and Humidity Sensor
T15h Tags are equipped with on-board temperature and humidity sensors that
can accurately monitor ambient temperature and humidity levels. Alerts are
triggered if the values are out of a configured range, either on the tag itself or
through MobileView (depending on configuration).
Programmable Logging Interval
Logging intervals can be programmed to 1, 5, or 15-minute intervals using pre-
configured static configurations.
Manual Audit with a Single Button Press
A physical inspection of the tag can be easily logged by pressing the main
button on the front of the tag.
Stores up to 128,000 Records
The T15
temperature readings and 64,000 humidity readings). Additionally,
temperature and humidity data is also sent to MobileView (if the tag is
configured to sync with MobileView).
Easy Battery Replacement
The tag uses 2x 1.5V Alkaline AA batteries. Battery levels are constantly
monitored and easily replaced by opening the battery cover on the back of the
tag.
Off-Line Monitoring
The T15h Tag can store data during times of network connectivity failures.
Recorded data is then automatically synchronized with MobileView within 24
hours after normal network connectivity has resumed, or immediately by
performing a manual sync from the tag. Off-line data is viewed via MobileView
Reports.
Flexible Mounting Options
The tag is supplied with a cradle that can be easily mounted to assets using
either double-sided tape or screws.
Multi-Language Text Display
The text can be set to 5 additional languages (besides English);
French, Swedish, Finnish, Spanish and Portuguese.

T15h Tag Deployment & User Guide
11
The following describes the parts of the T15h Tag:
Front View:
Back View:
Bottom View:
1
2
3
4
5
6
8
9
7

T15h Tag Deployment & User Guide
12
No.
Description
1
3 indication LEDs See LED and Buzzer Indications
2
LCD Screen
3
Sensor Air Vent & Buzzer See LED and Buzzer Indications
4
Navigation Arrow Buttons and Select Button
See Using the T15h Tag
5
Mute Alarm/Audit button
6
Sensor Air Vent
7
Battery Cover
8
USB-C Screw Tightening Hole (for securing the cable plug to the tag)
9
Power USB-C Connector
Screen Values
The
No.
Description
1
Current temperature
2
(displayed only if Show
Thresholds has been selected See Show/Hide Thresholds)
3
Current humidity
4
humidity range (displayed only if Show
Thresholds has been selected See Show/Hide Thresholds)
1
2
3
4

T15h Tag Deployment & User Guide
13
Status Icons
The
following table explains the Status Icons:
Icon
Description
Full Battery
Battery Level Medium
Battery Low
Depleted Battery. Change battery immediately
Power cable plugged in and supplying power to the tag
Power cable disconnected
Temperature and/or Humidity out-of-range Alert / Local Alarm
Bidirectional (BD) Session in progress
BLE Session in progress
Warning message See Viewing Warnings

T15h Tag Deployment & User Guide
14
The navigation buttons are used to navigate and select a menu option, change
the temperature scale and enable or disable the button sound.
button is used for tag activation, muting alarms, and performing temperature
audits.
are indicated by the menu icon .
1. Press the Select button to access the menu.
2. Use the left arrow button for up, and the right arrow button for
down, to navigate through the menu.
3. To select an option, navigate to the required option and press the Select
button .
Tag Menu Options
Option
Description
Main Screen
Displays the t .
BLE Activation
Select this option to activate a BLE session with the Deployment
Manager (DM) app. The BLE will be active for 30 min.
Tag Sync
Select this option to activate a BD session with MobileView.
Show Thresholds
Shows or Hides temperature and humidity out-of-range threshold
values on the main screen.
Min/Max Values
Shows the recorded temperature and humidity values since the last
audit.
Warnings
Shows any current warning messages. See Warning Messages
About
Languages
Changes the screen display language. English is the default setting.
Other available languages include French, Swedish, Finnish, Spanish,
and Portuguese.

T15h Tag Deployment & User Guide
15
T15h Tags arrive deactivated and must be activated and configured before
use.
Tag Activation
The tag is automatically activated once power is supplied to the tag (battery or
external power). The tag will beep when it turns on and is activated, and a blue
LED will flash. The tag will also automatically activate its BLE and will be ready
for configuration via the DM app .
Additionally, if the tag was deactivated using the DM app, the tag can be
activated again by pressing the main button on the front of the tag for 3
seconds.
Note: When activating the tag for the first time (supplying power) the warning
icon will appear. This indicates that the tag has not been configured yet.
Tag Configuration
It is recommended to use the Deployment Manager (DM) Setup & User Guide
together with the procedures below.
T15h Tag parameters must be initially configured using the DM BLE Tag
Functions feature. The feature needs to be enabled using a product key. See
below:
Enabling BLE Tag Functions
BLE Tag Functions is enabled (disabled by default) using the product key
PERF2197. The key only needs to be entered in once. If you delete the DM
app, the key will need to be re-entered. Note: By default, Wi-Fi channels 1-11
are open. Opening channels 12 and 13 is country-dependent and requires a
specific key from STANLEY Support.
1. Open the DM app.
2. Tap the Settings icon.

T15h Tag Deployment & User Guide
16
3. Tap Product Key.
4. Enter the Product Key PERF2197.
5. Tap Add Key.

T15h Tag Deployment & User Guide
17
6. Ensure that you can now manage BLE tags.
7. Tap Close.
8. BLE Tag Functions > Tag Management is now enabled.
Enabling Secured Tag Communication with MobileView
Note: This section is for sites that are using MobileView in a secured mode
and require secure BD (Bidirectional) tag sessions. For more information on
using MobileView in a secured mode, refer the latest MobileView Deployment
Guide.
Skip this section if the site is not using MobileView in a secured Mode or if you
will be deploying the tag in a UD (Unidirectional) environment. See
Configuring Tags.
T15h Tags support a HTTPS connection with MobileView Servers using the
TLS1.2 protocol. This allows MobileView Server authentication using pre-
installed X.509 certificates.

T15h Tag Deployment & User Guide
18
The STANLEY T15h Tag Certificate
To allow a MobileView Server
the T15h Tag must be pre-loaded with a Root CA certificate that authenticates
through an Intermediate Certificate using a Chain of Trust (see Error!
Reference source not found.).
The T15h Tag must be pre-loaded with only a Root CA certificate. Any other
certificate that is pre-load
verification.
Certificate Format
T15h Tags can be pre-loaded with a Root CA certificate in X.509v3 PEM format
-----BEGIN
CERTIFICATE----- -----END CERTIFICATE-----
MobileView Server Certificates
The following certificates must be pre-installed on the MobileView Server to
allow the certificate validation to be performed by T15h Tags:
•SSL Certificate issued for this specific server
•All Intermediate Certificates
•Root CA Certificate
If one of the above certificates from the Chain of Trust is not installed on the
MobileView Server, the T15h
verification.
MobileView Server Host Name
The M -
srv-1.corp.aeroscout.com). The domain must correspond to the CN set in
Certificate Definitions
T15h Tag certificate-based authentication of the MobileView Server is based
on the following definitions:
Chain of Trust
A certificate chain is an ordered list of certificates, containing an SSL
Certificate, Intermediate Certificates and a Root CA Certificate, that enable the
receiver to verify that the sender and all CA's are trustworthy.

T15h Tag Deployment & User Guide
19
certificate in the chain must be signed by the entity identified by the next
certificate in the chain.
The below figure illus
Certificate to the Root CA Certificate, where the Chain of Trust begins:
The Root CA certificate
The chain ends with a Root CA Certificate. The Root CA Certificate is always
signed by the CA itself. Using this certificate T15h Tags are able to verify the
signatures of all certificates in the chain.
The Intermediate Certificate
Any certificate that sits between the SSL Certificate and the Root CA
Certificate is called a chain or Intermediate Certificate. The Intermediate
Certificate is the signer/issuer of the SSL Certificate. The Root CA Certificate is
the signer/issuer of the Intermediate Certificate. If the Intermediate Certificate
is not installed on the MobileView Server (where the SSL certificate is installed)
it will prevent T15h
verification.
Exporting a Secured Certificate from MobileView
A secured server Certificate is exported from MobileView by doing the
following:
Open the secured MobileView in a browser (use the full DNS name).
Click on the Lock icon in the browser- IE or Chome.
Click on View certificates (IE) or Certificate (Chrome).

T15h Tag Deployment & User Guide
20
Click on the Certification Path tab.
Double click on certification name.
Select the Details tab and then click on