Star Trac E-TBT 9-6080 User manual

Maintenance Mode
STAR TRAC FITNESS 1 of 3 637-1374 Rev: A
Setting Definitions
E-TBT, Model 9-6080, LED Display
The display assembly contains two modes for settings.
•Manager Mode
•Maintenance Mode
In these modes, there are settings that can be changed for the club/facility or country for which the Total Body Trainer has
been installed. There are also technical settings which determine how the unit will perform.
Engaging Manager Mode
1. From the idle screen (powered on but not in a program), press and hold , then , then .
2. A beep will sound and “MANAGER SETTINGS” will display in the information window.
3. Release all keys. “SERIAL NUMBER” will display in the information window.
Engaging Maintenance Mode
1. From the idle screen (powered on but not in a program), press and hold , then , then .
2. A beep will sound and “MAINTENANCE SETTINGS” will display in the information window.
3. Release all keys. “SERIAL NUMBER” will display in the information window.

Maintenance Mode
STAR TRAC FITNESS 2 of 3 637-1374 Rev: A
Once in the Engineering Mode
SCROLL Keys: Display the next or previous parameter.
Increase and Decrease LEVEL Keys: Adjust the value of the displayed parameter up and down.
OK Key: Enters sub-menus or saves and exits from menu.
Next to the setting name is a letter (
A
). Each letter represents the type of setting it is.
A – The setting can’t be changed.
B – The setting can be changed manually.
C – The setting has fixed options which can be changed.
T – The setting is a test mode.
Maintenance Mode Settings
SERIAL NUMBER
B
This is the last 5 digits of the serial number set by the factory. It is used for reference only and
does not have any warranty implications.
DATE
B
This should be set to the month and year that the treadmill was manufactured. Example: 12.10
would be December 2010. This is used as a reference only.
DISPLAY VERS 1
A
Shows the actual software version on micro controller #1 (Primary Software)
DISPLAY VERS 2
A
Shows the actual software version on micro controller #2 (Secondary Software)
LCB VERS
A
Load Control Board (LCB) software version.
CCB VERS
A
Shows the actual software version on the CCB (Center Control Board). Only on units with a
PVS (Personal Viewing Screen) attached.
USB VERS
A
Shows the actual software version of the USB driver (located on the CCB). Only on units with a
PVS (Personal Viewing Screen) attached.
UNITS
C
Shows which unit of measurement is being used.
Options are:
1. English (mph)
2. Metric (km/h)
TIME
B
The maximum number of minutes that a program can run (excluding warm-up and cool-down).
The time my may changed by the facility. The range is from 5 – 99.
WEIGHT
B
The default weight of a user when the ‘Quick Start’ program is used. This value is used in the
calorie count algorithm.
When UNITS=English the value reflects lbs, when UNITS=Metric the value reflects kg’s.

Maintenance Mode
STAR TRAC FITNESS 3 of 3 637-1374 Rev: A
LANGUAGE
C
The user interface language.
The options are: English, Dutch, French, German, Portuguese, Spanish, Swedish, Italian and
Katakana
MODEL
C
•Bike = Upright or Recumbent Bikes
•TBT = Total Body Trainer (TBT’s WITH ADJUSTABLE Upper Body motion – Select Fit)
•TBT (NO UB) = Total Body Trainer (TBT’s WITHOUT ADJUSTABLE Upper Body
motion – Select Fit). This is the correct setting for model 9-6080.
•Stepper = Stepper
LCB TYPE
A
Shows the type of LCB
CSAFE
C
Allows the CSAFE port to be turned on for external systems like Fitlinxx to communicate with
the unit. This option can be turned ‘on’ or ‘off’.
PVS
C
ATSC/NTSC or PAL/SECAM, RF Signal for PVS
WALL POWER
C
Turns the wall power setting ‘on’ or ‘off’.
This setting should be set to ‘off’ as long as there is no external power source plugged in.
AUTO FAN
C
Auto Fan will turn the fan on automatically after one minute into the work out. This function can
be turned ‘on’ or ‘off’.
CLUB ID= For clubs that are part of the eFitness online program.
OPER HOURS
A
This shows the number of hours the product has been used.
QUICKSTART
A
Number of times the Quick Start Program was run since last reset.
MANUAL
A
Number of times the Manual Program was run since last reset.
TB BEGIN
A
Number of times the Total Body - Beginner program was run since last reset.
Depending on model settings. Value shown will be zero if model is set to “TBT (NO UB)”.
TB INTER
A
Number of times the Total Body - Intermediate program was run since last reset.
Depending on model settings. Value shown will be zero if model is set to “TBT (NO UB)”.
TB DIFF
A
Number of times the Total Body – Difficult program was run since last reset.
Depending on model settings. Value shown will be zero if model is set to “TBT (NO UB)”.
AUTO PILOT
A
Number of times the Auto Pilot Program was run since last reset.
IHR PROG
A
Number of times the Interval Heart Rate Control Program was run since last reset.
CHR PROG
A
Number of times the Constant Heart Rate Control Program was run since last reset.
CW PROG
A
Number of times the Continuous Watts Program was run since last reset.
ALPINE
A
Number of times the Alpine Pass Program was run since last reset.
RNDM PROG
A
Number of times the Random Hill Program was run since last reset.
COMM LOST
A
Number of times a ‘Communication Lost’ condition occurred since last reset.
KEY DOWN
A
Number of times a ‘Key Down’ condition occurred since last reset.
BATT LOW
A
Number of times that the battery voltage measured between 5.3 and 5.7 volts.
REPL BATT
A
Number of times that the battery voltage measured below 5.3 volts.
LED TEST
T
This is a test used to verify that all the LED (lights) on the display are operational.
KEYPAD TEST
T
This is a test used to verify that all the keys are responding on the display.
HEART RATE TEST
T
This is a test used to verify that the contact and/or telemetry heart rate is working.
FAN TEST
T
This is a test used to verify that the fan is working.
CSAFE TEST
T
This is a test used to verify that the CSAFE option is working.
MEASUREMENTS
T
This is a test used to see the actual voltage of the battery.