Star HSP7000 User manual

HYBRID PRINTER
HSP7000 SERIES
Hardware Manual

Trademark acknowledgments
HSP7000: Star Micronics Co., Ltd.
Notice
•All rights reserved. Reproduction of any part of this manual in any form whatsoever, without
STAR’ s express permission is forbidden.
•The contents of this manual are subject to change without notice.
•All e󱐯orts have been made to ensure the accuracy of the contents of this manual at the time of
going to press. However, should any errors be detected, STAR would greatly appreciate being
informed of them.
•The above notwithstanding, STAR can assume no responsibility for any errors in this manual.
© Copyright 2008-2011 Star Micronics Co., Ltd.
Federal Communications Commission
Radio Frequency Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This statement will be applied only for the printers marketed in U.S.A.
FCC WARNING
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.
For RF interference suppression, if a ferrite core is provided with this device, afx it to the interface cable.
Statement of
The Canadian Department of Communications
Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The above statement applies only to printers marketed in Canada.

TABLE OF CONTENTS
1. Unpacking and Installation.....................................................................................................................1
1-1. Unpacking ....................................................................................................................................1
1-2. Choosing a place for the printer...................................................................................................2
1-3. Removing the protective materials ..............................................................................................3
2. Parts Identication and Nomenclature..................................................................................................4
3. Setup..........................................................................................................................................................5
3-1. Connecting the Interface Cable to the PC....................................................................................5
3-2. Connecting the Interface Cable to the Printer..............................................................................7
3-3. Installing the Printer Software ...................................................................................................11
3-4. Connecting the Optional AC Adapter ........................................................................................12
3-5. Turning Power On......................................................................................................................13
3-6. Switch Cover Installation...........................................................................................................14
3-7. Connecting to a Peripheral Unit.................................................................................................15
3-8. Attaching the Interface Cover....................................................................................................16
4. Loading the Ribbon Cartridge and Paper...........................................................................................17
4-1. Loading the Ribbon Cartridge ...................................................................................................17
4-2. Loading the Paper Roll ..............................................................................................................18
4-3. Loading the Slip Paper or Validation Paper ...............................................................................20
4-4. Scanning MICR Characters .......................................................................................................21
5. Consumable Parts and AC Adapter .....................................................................................................24
5-1. Thermal Paper Roll ....................................................................................................................24
5-2. Slip Paper ...................................................................................................................................26
5-3. AC adapter (option) ...................................................................................................................27
6. Control Panel and Other Functions .....................................................................................................28
6-1. Control Panel .............................................................................................................................28
6-2. Errors..........................................................................................................................................29
6-3. Self-Printing...............................................................................................................................31
6-4. Cleaning Mode...........................................................................................................................35
6-5. Sensor Adjustment .....................................................................................................................35
7. Adjusting the Near-end Sensor .............................................................................................................41
8. Preventing and Clearing Paper Jams...................................................................................................43
8-1. Preventing Paper Jams ...............................................................................................................43
8-2. Removing Paper Jam .................................................................................................................43
8-3. Releasing a Locked Cutter .........................................................................................................45
9. Maintenance ...........................................................................................................................................46
9-1. Thermal Printer ..........................................................................................................................46
9-2. Slip Printer .................................................................................................................................47
9-3. MICR Head................................................................................................................................47
9-4. Cleaning the Sensors and the Surrounding Area........................................................................48
9-5. Cleaning the Paper Holder and the Surrounding Area...............................................................48

10. Specications ........................................................................................................................................49
10-1. General Specications ...............................................................................................................49
10-2. Auto Cutter Specications .........................................................................................................50
10-3. MICR Specications..................................................................................................................50
10-4. External Specications...............................................................................................................51
10-5. Interface Specications..............................................................................................................52
10-6. Power Specs ...............................................................................................................................53
10-7. Environmental Requirements.....................................................................................................54
10-8. Reliability Specications ...........................................................................................................55
11. Dip Switch Setting ................................................................................................................................57
11-1. Parallel Interface Model.............................................................................................................58
11-2. RS-232C Interface Model ..........................................................................................................59
11-3. USB/PoweredUSB Interface Model ..........................................................................................61
11-4. Ethernet Interface Model ...........................................................................................................62
12. Parallel Interface..................................................................................................................................64
13. RS-232C Serial Interface.....................................................................................................................65
13-1. Interface Specications ..............................................................................................................65
13-2. RS-232C Connector ...................................................................................................................66
13-3. Cable Connections .....................................................................................................................67
14. USB/PoweredUSB and Ethernet ........................................................................................................68
14-1. USB/PoweredUSB Interface Specications ..............................................................................68
14-2. Ethernet Interface Specications................................................................................................68
15. Peripheral Unit Drive Circuit .............................................................................................................69
16. Memory Switch Settings......................................................................................................................71
Please access the following URL
http://www.star-m.jp/eng/dl/dl02.htm
for the latest revision of the manual.

– 1 –
1. Unpacking and Installation
1-1. Unpacking
After unpacking the unit, check that all the necessary accessories are included in the package.
Note:The ferrite core and fastener provided with your
printer depend on your printer conguration.
Fig. 1-1 Unpacking
If anything is missing, contact the dealer where you bought the printer and ask them to supply
the missing part. Note that it is a good idea to keep the original box and all the packing materials
just in case you need to pack the printer up again and send it somewhere at a later date.
Note
Printer
Thermal paper roll
Switch blind
Setup sheets
CD-ROM
Paper guide
ERROR
PAPER OUT
SLIP FEED RELEASE
POWER
Interface cover
Ribbon cassette

– 2 –
1-2. Choosing a place for the printer
Before actually unpacking the printer, you should take a few minutes to think about where
you plan to use it. Remember the following points when doing this.
P Choose a rm, level surface where the printer will not be exposed to vibration.
PThe power outlet you plan to connect to for power should be nearby and unobstructed.
PMake sure that the printer is close enough to your host computer for you to connect
the two.
P Make sure that the printer is not exposed to direct sunlight.
P Make sure that the printer is well away from heaters and other sources of extreme heat.
PMake sure that the surrounding area is clean, dry, and free of dust.
PMake sure that the printer is connected to a reliable power outlet. It should not be on
the same electric circuit as copiers, refrigerators, or other appliances that cause power
spikes.
PMake sure that the room where you are using the printer is not too humid.
PThis device employs a DC motor and switches that have an electrical contact point.
Avoid using the device in environments where silicon gas can become volatile.
PWhen disposing of the printer, obey local regulations.
WARNING
PShut down your equipment immediately if it produces smoke, a strange odor, or unu-
sual noise. Immediately unplug the equipment and contact your dealer for advice.
PNever attempt to repair this product yourself. Improper repair work can be dangerous.
PNever disassemble or modify this product. Tampering with this product may result in
injury, re, or electric shock.

– 3 –
1-3. Removing the protective materials
Four protective materials are inserted into the printer to protect components during shipping.
Before using the printer, be sure to remove all protective materials as shown in the illustra-
tion.
(1) Remove the three tapes and pull the two protective sheets.
(2) Open the front cover.
Remove the tape on the front cover, and then remove the sheet.
Next, pull the protective sheet that is securing the head straight out of the unit.
Note:That it is a good idea to keep all protective materials in case you will need to pack
the printer up again and send it somewhere at a later date.
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
1
1
2
2
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
Front cover

– 4 –
2. Parts Identication and Nomenclature
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
Power switch
Used to turn on/off
power to the printer.
Interface connector
For connection to a
host computer.
Validation slot
Insert paper here.
Front cover
Open it to replace the ribbon.
Do not open it during printing.
Slip slot
Insert paper here.
Rear cover
Open it to replace the roll paper.
Do not open it during printing.
Cutter cover
Open it to clear paper jam.
Do not open it during printing.
Control panel
Features LED indicators
to indicate printer status
and switches to operate
the printer.
Cover open lever
Push this lever in the direction of the
arrow to open the rear cover.
Peripheral drive connector
Connects to peripheral units such
as cash drawers, etc.
Do not connect this to a telephone.
Power connector
For connection of the AC adapter.
Never unplug the AC adapter while
the printer is on.

– 5 –
3. Setup
3-1. Connecting the Interface Cable to the PC
CAUTION
The optional USB, PoweredUSB, and LAN cables have been designed specically for this unit
(HSP7000).
Other USB, PoweredUSB, and LAN cables may not meet the EMC technical standards.
3-1-1. Parallel Interface Cable
Connect the parallel interface cable to a parallel port
of your PC.
3-1-2. RS-232C Interface Cable
Connect the RS-232C interface cable to a RS-232C
port of your PC.
3-1-3. USB Interface Cable
Connect the USB interface cable to a USB port of
your PC.
Option: USB cable 1.8M TSP1 (P/N: 30729100)

– 6 –
3-1-4. PoweredUSB Interface Cable
Attach the ferrite core to the PoweredUSB interface cable, and connect the cable to a Pow-
eredUSB port of your PC.
Option: POWERED USB CABLE 1X8LNL 1.2M (P/N: 30729130)
Star Recommended PCI Card: PCI to 4 Port PoweredUSB Card (Model: 301-1150-01; manufacturer:
Digi)
3-1-5. Ethernet Interface cable
Attach the ferrite core to the Ethernet interface cable, and connect the cable to an Ethernet port
of your PC.
Option: LAN cable 1.0M TSP1E (P/N: 30729200)
Maximum 3.5 cm
Pull and cut
Pull and cut
Maximum 3.5 cm

– 7 –
3-2-1. Parallel Interface Cable
(1) Make sure the printer is turn off.
(2) Afx the ferrite core onto the cable as shown in
the illustration.
(3) Pass the fastener through the ferrite core.
(4) Loop the fastener around the cable and lock it.
Use scissors to cut off any excess.
(5) Connect the interface cable to the connector on
the rear panel of the printer.
(6) Fasten the connector clasps.
3-2. Connecting the Interface Cable to the Printer
Note that the interface cable is not provided. Please use a cable that meets specications.
CAUTION
The optional USB, PoweredUSB, and LAN cables have been designed specically for this unit
(HSP7000).
Other USB, PoweredUSB, and LAN cables may not meet the EMC technical standards.
Before connecting or disconnecting an interface cable (except when using a PoweredUSB cable),
be sure to disconnect the plug of the AC adapter power cable from the outlet.
Ferrite core
Interface cable
5 cm
(maximum)
Fastener
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
Parallel interface
cable
Pull and cut

– 8 –
3-2-2. RS-232C Interface Cable
(1) Make sure the printer is turn off.
CAUTION
Before connecting/disconnecting the interface ca-
ble, make sure that power to the printer and all the
devices connected to the printer is turned off. Also
make sure the power cable plug is disconnected
from the AC outlet.
(2) Connect the interface cable to the connector on
the rear panel of the printer.
(3) Tighten the connector screws.
3-2-3. USB Interface Cable
Afx the ferrite core onto the USB cable as shown in the illustration below and make sure to
pass the cable through the cable support as shown in the illustration.
Option: USB CABLE 1.8M TSP1 (P/N: 30729100)
(1) Afx the supplied ferrite core onto the USB cable as shown in the illustration.
(2) Secure the cable with the cable hook.
(3) Insert the plug of the USB interface cable into the USB interface connector of the printer
as shown in the illustration.
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
RS-232C
interface
cable
Ferrite core
4 cm (Maximum)

– 9 –
3-2-4. PoweredUSB Interface Cable
(1) Turn the power switch off.
(2) If connected to an AC adapter, pull the power cord plug from the outlet and then pull the
plug from the power connector on the printer side.
CAUTION
If connecting a PoweredUSB cable, do not connect the AC adapter because this can cause a
malfunction.
(3) Afx the ferrite core onto the cable as shown in the illustration.
Option: POWERED USB CABLE 1X8LNL 1.2M (P/N: 30729130)
(4) Pass the fastener through the ferrite core.
(5) Loop the fastener around the PoweredUSB interface cable and lock it.
Use scissors to cut off any excess.
(6) Connect the interface cable to the connector on the rear panel of the printer.
Pull and cut
Ferrite core
Interface cable
Maximum
3.5 cm
Fastener

– 10 –
3-2-5. Connecting Ethernet Interface Cable
To protect the unit from electromagnetic interference, afx the two supplied ferrite cores to the
printer and router (hub) sides of the cable, respectively. Follow the instructions given below.
Option: LAN CABLE 1.0 M TSP1E (P/N: 30729200)
(1) Make sure the printer is turned off.
(2) Afx the ferrite core onto the Ethernet cable as shown in
the illustration below.
(3) Pass the fastener through the ferrite core.
(4) Loop the fastener around the cable and lock it. Use scis-
sors to cut off any excess.
(5) Connect the interface cable to the connector on the
rear panel of the printer.
Link disconnection detection feature
The Ethernet interface model is equipped with a link
disconnection detection feature.
If the printer is turned on when an Ethernet cable is not
connected to it, the POWER and ERROR lamps are
simultaneously turned on and off at 2-second intervals
to indicate the disconnection.
Be sure to connect the Ethernet cable from a PC or hub
to the printer, and then turn the printer on.
Ferrite core
Ethernet cable
10 cm
(maximum)
Fastener
Pull and cut

– 11 –
3-3. Installing the Printer Software
Here is the procedure for installing the printer driver and utility software, which are stored on
the supplied CD-ROM.
The procedure applies to the Windows operating systems shown below.
For Macintosh and Linux, refer to the software manual in the Mac folder or Linux folder of
the CD-ROM.
• Windows 2000
• Windows XP
• Windows Vista 32-Bit/64-Bit
(1) Turn ON the power to your PC to start Windows.
(2) Insert the supplied CD-ROM (Drivers and Utilities)
into the CD-ROM drive.
(3) Follow the instructions that appear on the screen.
(4) The dialog shown in the illustration indicates that
the procedure has been completed.
Click “Finish”.
The dialog that appears on the screen varies with your system. This completes the installation
of the printer software. A message will appear, prompting you to restart. Restart Windows.
For instruction on the Windows Vista 64-Bit, refer to the software manual located in the
“Documents” folders on the CD-ROM.

– 12 –
3-4. Connecting the Optional AC Adapter
Note:Before connecting/disconnecting the AC adapter, make sure that power to the printer
and all the devices connected to the printer is turned off. Also make sure the power
cable plug is disconnected from the AC outlet.
(1) Connect the AC adapter to the power cable.
Note: The optional AC adapter has been designed specically for this unit (HSP7000).
Other AC adapters may not meet the EMC technical standards.
Option: PS60A-24B
(2) Connect AC adapter to the connector on the printer.
(3) Insert the power cable plug into an AC outlet.
CAUTION
When disconnecting the cable, take hold of the cable
connector to pull it out. Releasing the lock makes it easy
to disconnect the connector.
Pulling the cable excessively could cause damage to the
connector.
POWER ERROR
PAPER OUT
SLIP FEED RELEASE

– 13 –
3-5. Turning Power On
Make sure that the Power cord has been connected as described in 3-4.
Turn ON the power switch located on the front of the printer.
The POWER lamp on the control panel will light up.
CAUTION
We recommend that you unplug the printer from the power outlet whenever you do not plan to
use it for long periods. Because of this, you should locate the printer so that the power outlet it
is plugged into is nearby and easy to access.
When an Switch blind is afxed to the printer above the power switch, the ON/OFF marks of
the power switch may be hidden. If this occurs, remove the power cord from the outlet to turn
the printer OFF.
Power switch
POWER ERROR
PAPER OUT
SLIP FEED RELEASE

– 14 –
3-6. Switch Blind Installation
It is not necessary to install the switch blind. Only install it if it is necessary for you. By install-
ing the switch blind, the following become possible.
• Preventing the power switch from being operated by mistake.
• Ensuring that other people can not easily operate the power switch.
Install the switch blind as shown in the diagram below.
The power switch can be turned ON (
|
) and OFF (O) by inserting a narrow instrument (ball
pen etc.) in the holes in the switch blind.
CAUTION
We recommend that you unplug the printer from the power outlet whenever you do not plan to
use it for long periods. Because of this, you should locate the printer so that the power outlet it
is plugged into is nearby and easy to access.
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
Switch blind

– 15 –
3-7. Connecting to a Peripheral Unit
You can connect a peripheral unit to the printer using a modular plug.
See “15. Peripheral Unit Drive Circuit” for details about the type of modular plug that is re-
quired. Note that this printer does not come with a modular plug or wire, so it is up to you to
obtain one that suits your needs.
CAUTION
Make sure that the printer is turned off and unplugged from the AC outlet and that the computer
is turned off before making connections.
(1) Make sure the printer is turned off.
(2) Afx the ferrite core onto the peripheral drive cable as shown below.
(3) Pass the fastener through the ferrite core.
(4) Loop the fastener around the peripheral drive cable and lock it.
Use scissors to cut off any excess.
(5) Connect the peripheral drive cable to the connector on the rear panel of the printer.
CAUTION
Do not connect a telephone line into the peripheral drive connector. Failure to observe this may
result in damage to the printer.
Also, for safety purposes, do not connect wiring to the external drive connector if there is a
chance it may carry peripheral voltage.
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
Peripheral drive cable
Ferrite core
Pull and cut
3.5 cm (maximum)

– 16 –
3-8. Attaching the Interface Cover
It is not necessary to attach the interface cover. Only attach it if it is necessary for you.
Attach the interface cover as shown in the illustration.
(1) Place the printer as shown below.
(2) Install the interface cover by aligning the tabs on the interface cover with the grooves in
the printer case.
(3) Place the AC cable and the interface cable in the cutout of the interface cover. Then, install
the interface cover until the both ends of the interface cover click into place.
POWER ERROR
PAPER OUT
SLIP FEED RELEASE
Interface cover