StarTech.com SAT3520UERGB User manual

SAT3520U2ER
SAT3520UERGB
InfoSafe eSATA/USB 2.0 Dual
3.5” SATA Drive Enclosure
with RAID
Instruction Manual

FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and
do not represent an endorsement of a product or service by StarTech.com, or an en-
dorsement of the product(s) to which this manual applies by the third-party company in
question. Regardless of any direct acknowledgement elsewhere in the body of this doc-
ument, StarTech.com hereby acknowledges that all trademarks, registered trademarks,
service marks, and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

Instruction Manual
i
Instruction Manual
Table of Contents
Introduction .................................................................... 1
Features ......................................................................................1
Package Contents .......................................................................1
Hardware Guide............................................................... 2
Front View....................................................................................2
Rear View ....................................................................................2
Installation....................................................................... 3
Installing Drives in the Enclosure ................................................3
Connecting SAT3520U2ER to the Host Computer......................5
Partitioning Installed Drives.........................................................5
Software Operation Guide.............................................. 8
Software Installation Guide..........................................................8
Using the SteelVine Manager......................................................9
Changing the RAID Mode Using the GUI....................................9
RAID Mode Overview ..................................................................11
Specifications.................................................................. 14
Technical Support........................................................... 15
Warranty Information...................................................... 15

Instruction Manual
1
Introduction
Thank you for purchasing a StarTech.com InfoSafe eSATA/USB 2.0
Dual 3.5” SATA Hard Drive Enclosure with RAID. This versatile storage
solution allows easy installation of two 3.5” SATA I/II hard drives of up to
2TB capacity (each), for a total capacity of up to 4TB (non-RAID), and
maximizes performance capabilities with support for a broad range of
RAID applications including RAID 0, RAID 1, and Concatenated (BIG
mode).
Features
• Rear panel power and fan on/off switches
• Easy configuration using dip switches or GUI
• Hard drive power and activity LEDs
• Supports data transfer speeds of up to 3Gbps (eSATA) and 480Mbps
(USB 2.0)
• RAID can be used with either eSATA or USB 2.0 connection
• Supports RAID 0 (Striping or Fast), RAID 1 (Mirroring or Safe),
BIG (Spanning or Concatenation), SAFE33/55 and JBOD modes
• Built-in 50mm cooling fan
Package Contents
• 1 x Aluminum Enclosure
• 1 x eSATA Cable
• 1 x Instruction Manual
• 1 x Software and Driver Installation CD
• 1 x Plastic Stand
• 1 x Power Adapter with Power Cord
• 1 x Screw Kit
• 1 x USB Cable

Instruction Manual
2
Hardware Guide
Front View
1.Power LED
2.HDD-1 LED
3.HDD-2 LED
Rear View
1. Fan
2. eSATA Connector
3. Power Switch
4. Power Adapter Socket
5. Fan Switch
6. USB Connector
1
2
3
1
2
3
4
5
6

Instruction Manual
3
Installation
Installing Drives in the Enclosure
1. Remove the screws holding the rear panel
in place, then slide the rear panel out from
the enclosure.
2. Place the first 3.5” SATA hard drive into
the tray, then slide it forward until the drive
interface is firmly connected to the SATA
connector on the SAT3520U2ER/
SAT3520UERGB. Repeat this step with
the second 3.5” SATA hard drive, using the
remaining tray.
If connecting the enclosure to a host computer using the eSATA
port, please note that in order to use some of the RAID modes of the
enclosure, the eSATA port on the host computer system must provide
Port Multiplier support. If the eSATA port does not offer Port Multiplier
support, only one of the installed drives will be accessible.

Instruction Manual
4
3. Secure the drives to the Enclosure tray,
using the provided screws.
4. Select the operating mode for your hard drive using the DIP Switches
shown below. Once you have set the DIP switches according to the
desired RAID mode, press the Reset Button to save changes.
DIP Switches
Reset Button
DIP Switch No.
RAID Mode 1 2 3 4
GUI* (Requires Software Installation)** ON ON ON ON
JBOD* ON OFF OFF ON
BIG ON OFF OFF OFF
RAID 0 (Fast) ON OFF ON OFF
RAID 1 (Safe) ON OFF ON ON
RAID/SAFE33* ON ON OFF OFF
RAID/SAFE55* ON ON OFF ON
*denotes Port Multiplier requirement over eSATA
** Please see pg. 11 for more details on GUI Mode

Instruction Manual
5
5. Replace the Enclosure tray (with drives
attached) into the Enclosure.
6. Secure the Enclosure tray within the Enclosure, using the screws
removed in step 1.
Connecting SAT3520U2ER to the Host Computer
Once the hard drives have been installed within the Enclosure and the
necessary dipswitch settings have been made:
1. Connect the power adapter (included) to the power adapter socket
on the rear panel of SAT3520U2ER. Connect the remaining end of the
power adapter to an available power outlet.
2. Connect SAT3520U2ER to the host computer using either an eSATA or
USB cable (both included).
NOTE: if using eSATA, the host controller on the computer system needs
to support Port Multiplier technology.
Partitioning Installed Drives
Once the necessary connection (either eSATA or USB) has been made to
the host computer, from the host computer operating system:
1. Right-click on the My Computer icon and select Manage.

Instruction Manual
6
2. In the left pane of the Computer Management window, select Device
Manager. The installed hard drives will appear as “unallocated”, in the
bottom half of the right pane.
3. Right-click the Disk you wish to use and select Initialize Disk.
4. Click OK to initialize the disk.

Instruction Manual
7
5. The disk should now be shown as “Online.” Right-click on the
unallocated block and select New Partition.
6. The New Partition Wizard will appear. Follow the on-screen
instructions to complete the creation of the new partition. When the
partition has been created, the hard drive should appear as “New
Volume.”
7. Repeat steps 1-6 to partition the second hard drive.