StarTech.com 5G4AINDRM-USB-A-HUB User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: June 22, 2023 2:54 PM
Product Diagram
Product ID
5G4AINDRM-USB-A-HUB
4-Port Managed Industrial USB Hub - USB 3.2 Gen 1 5Gbps, ESD Protection
7
1 3
4
Component Function
1DC 2-Wire Terminal Block Power
Input
• Connect a +7~48 V DC Power Source
• 30W or Higher Recommended for Maximum
Power Performance
2Power LED
• Indicates if the USB Hub is receiving power
• Solid Green - Receiving Power
• O - Not Receiving Power
3USB-B Host Port • Connect to a USB-A Port on a Host Computer
• USB 3.2 Gen 1 (5 Gbps)
43x USB-A Data/Charge Ports
• Connect USB Peripherals
• USB 3.2 Gen 1 (5 Gbps)
• Backward compatible with USB 2.0 (480Mbps)
• BC 1.2 for up to 5 V/1.5 A (7.5 W) Charging
5USB-A Data Port
• Connect USB Peripherals
• USB 3.2 Gen 1 (5 Gbps)
• Not Compatible with USB 2.0 (480Mbps)
• Supports up to 5 V/0.9 A (4.5 W) Charging
64x USB Port Status LEDs
• Indicates if the Corresponding USB-A Data/Charge
Port is Enabled or Disabled
• Solid Green - USB-A Data/Charge Port Enabled
• O - USB-A Data/Charge Port Disabled
• Enable/Disable USB-A Data/Charge Ports within the
USB Hub Management Software
7Mounting Brackets • Mount the USB Hub to a wall or the side/underside of
a Desk
7
Package Contents
• USB Hub x 1
• 6 ft [1.8 m] USB-A to USB-B Cable x 1
• Terminal Block Connector (Attached) x 1
• DIN Rail Mounting Bracket (with Mounting Screws) x 1
• Quick-Start Guide x 1
26 6
Requirements
• Host Computer
• USB-A Port
• 7-48V DC Power Source
• Flat head Screwdriver
• (Optional) Phillips head Screwdriver (for DIN Rail Mounting)
For the latest drivers, manuals, product information, technical specications, and
declarations of conformance, please visit:
www.StarTech.com/5G4AINDRM-USB-A-HUB
USB Hub Management Software
To utilize the management features of this USB Hub, it is necessary to download and
install the software. To download the USB Hub Management Software, as well as the
accompanying documentation, please visit:
www.StarTech.com/5G4AINDRM-USB-A-HUB
5

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a 2-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com
Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
Regulatory Compliance
FCC - Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
DIN Rail Mounting
This USB Hub includes a DIN Rail Bracket that can be used to vertically or horizontally
mount the USB Hub to a DIN Rail. To install the DIN Rail Bracket on the USB Hub:
1. Align the Din Rail Bracket with the DIN Rail Mounting Holes, located on at the back
of the USB Hub.
Note: The USB Hub features two sets of Vertical DIN Rail Mounting Holes, and one
set of Horizontal DIN Rail Mounting Holes. Any set may be used, depending upon the
desired conguration.
2. Insert the Mounting Screws (x 2) through the DIN Rail Brackets, and into the USB
Hub.
3. Using a Phillips Head Screwdriver tighten the Mounting Screws. Be careful not to
over-tighten the Mounting Screws.
Installation
Note: Connect the Power Source after all the other installation steps have been
completed.
Connect the USB Ports
1. Connect up to four USB peripherals to the USB-A Data/Charge Ports, located on the
USB Hub.
2. Connect a USB-A Port on the Host Computer to the USB-B Host Port, located on
the USB Hub, using the included USB-A to USB-B Cable.
• The Computer will automatically detect the device.
Power the Hub
Power the Hub Using the 2-Wire Terminal Block
1. Remove the Terminal Block Connector Housing from the USB Hub’s Casing.
2. Loosen the screws for the Terminals located on the Terminal Block Connector,
using a Flat Head Screwdriver.
3. Connect the Positive and Negative Wires from the 7-48V DC Power Source (not
included) to the Terminals on the Terminal Block Connector.
Note: Ensure the polarity of the power input is correctly matched with the DC 2-Wire
Terminal Block Pins to function properly and to prevent damage to the USB Hub and
any connected peripherals.
Terminal Block Pins
4. Insert the Terminal Block Connector Housing back into USB Hub.
V- (GND)
V+ (7~48V)
Vertical Conguration Horizontal Conguration