Stealth Products ADI User manual

Quick Reference
Carbon Fiber Seating
Seat Base Installation

i
Customer Satisfaction 1.0
Stealth Products strives for 100% customer satisfaction. Your complete satisfac-
tion is important. Please contact us with feedback or suggested changes that
will help improve the quality and usability of these products. You may reach us
at:
104 John Kelly Drive, Burnet, TX 78611
Phone: [phone] Toll Free: 1 [phone]
Fax: [phone] Toll Free: 1 [phone]
[e-mail] www.stealthproducts.com
General
Read and understand all instructions prior to the use of the product. Failure to
adhere to instructions and warnings in this document may result in property
damage, injury, or death. Product misuse due to failure of the following instruc-
tions will void the warranty.
Immediately discontinue if any function is compromised, parts are missing,
loose, or shows signs of excessive wear. Consult with your supplier for repair,
adjustment, or replacement.
If this document contains information you do not understand, or there are con-
cerns about safety or operation, contact your supplier.

ii
Important Information 2.0
Important Information!
All persons responsible for fitting, adjustment, and daily use of the devices dis-
cussed in these instructions must be familiar with and understand all safety as-
pects of the devices mentioned. In order for our products to be used successful-
ly, you must:
 Read and understand all instrucons and warnings.
 Maintain our products according to our instrucons on care and maintenance.
 Devices should be installed and adjusted by a trained technician.
Ordering Documentation
You can download additional copies of this User & Installation Manual on the
Stealth website: www.stealthproducts.com
REF P116D250R3
Document #250 Revision 3
Tuesday, February 16, 2016

iii
Introduction 3.0
Installation Date:
Dealer:
Dealer Stamp:
Serial Number:
For UK warranty claims, please contact:
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany

iv
Warranty 4.0
No person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
Stealth Products warrants against failure due to defective materials or workman-
ship:
Covers: 180 days
Hardware: 5 years
Electronics: 5 years
Limitations 4.1
Stealth Products, LLC does not warrant damage due to, but not limited to:
 Misuse, abuse, or misapplicaon of products.
 Modicaon of products without wrien approval from Stealth Products, LLC.
 Any alteraon or lack of serial number, where applicable, will automacally void the war-
ranty.
 Stealth Products, LLC is liable for replacement parts only.
 Stealth Products, LLC is not liable for any incurred labor costs.
NOTI CE
Any substitutions of supplied hardware void the warranty. Misuse of items and
“acts of nature” (ex. Flood, tornado, etc.) are not covered by the warranty.

v
Table of Contents 5.0
1.0 Customer Satisfaction…………………………………………………………….…….i
2.0 Important Information…………………………………………………………….…..ii
3.0 Introduction……………………………………………………………………………...iii
4.0 Warranty……………………………………………………………………………….….iv
4.1 Limitations…………………………………………………………………………………………….….iv
5.0 Table of Contents…………………………………………………………………….….v
6.0 Warning Labels………………………………………………………………………….vi
6.1 Warning Labels………………………………………………………………………………………...vi
6.2 Limited Liability………………………………………………………………………………………..vi
6.3 Testing……………………………………………………………………………………………………...vi
7.0 Installation Instructions………………………………………………………………..1
7.1 Tools Required for Installation…………………………………………………………………..1
7.2 Installation………………………………………………………………………………………………...1
8.0 First Time Use…………………………………………………………………………….3
8.1 Dealer Assistance……………………………………………………………………………………..3
8.2 User Testing……………………………………………………………………………………………..3
8.3 Conditions of Use………………………………………………………………………………….…3
9.0 Maintenance……………………………………………………………………………...4
9.1 Cleaning…………………………………………………………………………………………………....4
9.2 Disinfection……………………………………………………………………………………………….4

vi
Warning Labels 6.0
DANGER Identifies an imminent situation which (if not avoided) will
result in severe injury, death,and property damage.
WARNING Identifies a potential situation which (if not avoided) will
result in severe injury, death,and property damage.
CAUTIO N Identifies a potential situation which (if not avoided) will
result in minor to moderate injury,and property damage.
NOTICE
Identifies important information not related to injury, but
possible property damage.
SAFETY
Indicates steps or instructions for safe practices, reminders of
safe procedures, or important safety equipment that may be
necessary.
Warning Labels 6.1
Warnings are included for the safety of the user, client, operator and property.
Please read and understand what the signal words SAFETY, NOTICE, CAUTION,
WARNING and DANGER mean, how they could affect the user, those around
the user, and property.
Limited Liability 6.2
Stealth Products, LLC accepts no liability for personal injury or damage to
property that may arise from the failure of the user or other persons to follow
the recommendations, warnings, and instructions in this manual.
Testing 6.3
Initial setup and driving should be done in an open area free of obstacles until
the user is fully capable of driving safely.
The product should always be tested without any person sitting in the
wheelchair until every alteration of the physical installation or adjustment is
complete.

1
Installation Instructions 7.0
Tools Required for Installation 7.1
 1/2in. Open end wrenches, 2 each
 1/8in. allen key, 1 each
 Drill with 3/16in. Bit, 1 each
Installation 7.2
1. Prior to removing OEM seat sling, mark le and right chair frame at the front edge of the
OEM seat sling.
2. Place the front support mount on the frame approximately 2.5in. inside the front edge of
the original seat base locaon that was marked.
3. Place the rear support mount on the frame in the approximate weight bearing locaon of
the user.
NOTI CE
For reference purposes, support mounts come fully assembled. Seat bases are not pre-
drilled to avoid interference with other parts on the frame.

2
Installation Instructions 7.0
4. Rotate center hex bar so that the support mounts are “snug” within the frame tubes. Do
not over ghten. This will cause ex to the frame.
5. Place a board or straight edge across the support mounts and take out any buckling.
6. Tighten jam nuts with the 1/2in. wrench.
7. Place carbon ber seat base panel on the chair frame and center the edges.
8. In order to mount the seat base, you must rst mark each hole locaon through the
10/32in. Tapped holes in the support mount. Use 90° bent scribe or pick to mark holes.
9. Drill four 3/16in. holes where the seat base is marked.
10. Tighten the four 10/32in. buon screws with washers into the mounts.
WAR NI NG
Only use the hardware supplied with the CF Base. Do not substitute any other screws,
brackets, or clamps.

3
First Time Use 8.0
Dealer Assistance 8.1
During first time use by the client, it is advised that the dealer or service techni-
cian assists and explains the set-up to the customer (the user and/or the at-
tendant). If needed, the dealer can make final adjustments.
User Testing 8.2
It is important that the customer is fully aware of the installation, how to use it,
and what can be adjusted in order to gain as much mobility as possible. As a
dealer, proceed as follows:
 Explain and show the customer how you have executed the installaon, and explain the
funcon of the hardware.
 If needed, adjust the hardware to the proper posion.
 Explain to the customer possible problems and how to address them.
Conditions of Use 8.3
The ADI hardware is intended for use as installed by the dealer, in accordance
to the installation instructions in this manual.
 The foreseen condions of use are communicated by the dealer or service technician to
the user and/or aendant during the rst me use.
 If the usage condions change signicantly, please contact your dealer or a qualied ser-
vice technician to avoid excessive wear and tear or unintended damage.
CAUTIO N Protect the CF Back from blunt force shock that may cause damage
and/or breakage.
NOTI CE
The CF Base may not fit every chair. Please consult your clinician or supplier
providing your equipment.
CAUTIO N Do not use ADI backs during vehicle transportation.

4
Maintenance 9.0
WARNIN G 250lbs. (113.40 kg) user weight limit.
Cleaning 9.1
 Use a so cloth to clean the back shell
 Hand wash the foam pad cover with mild, soapy water or detergent and let dry.
Disinfection 9.2
 Wipe gently with a cloth dampened with a household disinfectant.
 Allow foam to air dry thoroughly.
WARNIN G Do not hand wash in water temperatures above 160°F (70°C).
WARNIN G Do not wash or machine dry.
SAFETY
Always check all mounting hardware, making sure they are securely fastened
before using the CF seat bases.
WARNIN G Do not immerse the foam in water.
NOTI CE
Altering an ADI back in any way and/or improper installation will void the
warranty.
CAUT ION
Institution MUST clean and disinfect product between multiple patient uses.

Stealth Products, LLC. • [e-mail] • www.stealthproducts.com
[phone] | [phone] | 104 John Kelly Drive, Burnet TX 78611
P116D250R3 Revision Date 2016-02-17