Stealth Products I-Drive IDCH Series Instructions for use

Quick Install
Alternative Drive Mounting Hardware
I-Drive Control Harness
IDCH
mo-Vis’:

i
Customer Satisfaction 1.0
Stealth Products strives for 100% customer sasfacon. Your complete sasfacon is
important. Please contact us with feedback or suggested changes that will help
improve the quality and usability of our hardware. You may reach us at:
Stealth Commitment 1.1
Installation Date:
Dealer:
Dealer Stamp:
Serial Number:
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
Stealth Products, LLC
104 John Kelly Drive, Burnet, TX 78611
Phone: [phone] Toll Free: 1(800) 965-9229
Fax: [phone] Toll Free: 1(800) 806-1225
[email protected] www.stealthproducts.com

ii
Warning Labels 2.0
Warning Labels 2.1
Warnings are included for the safety of the user, client, operator and property.
Please read and understand what the signal words SAFETY, NOTICE, CAUTION,
WARNING and DANGER mean, how they could affect the user, those around
the user, and property.
Limited Liability 2.2
Stealth Products, LLC accepts no liability for personal injury or damage to
property that may arise from the failure of the user or other persons to follow
the recommendations, warnings, and instructions in this manual.
Testing 2.3
Initial setup and driving should be done in an open area free of obstacles until
the user is fully capable of driving safely.
The i-Drive Control Harness and joystick should be tested by the care givers and
end user and adjusted specifically to their needs.
DANGER Identifies an imminent situation which (if not avoided) will
result in severe injury, death,and property damage.
WARNIN G Identifies a potential situation which (if not avoided) will
result in severe injury, death,and property damage.
CAUTION Identifies a potential situation which (if not avoided) will
result in minor to moderate injury,and property damage.
NOTI CE
Identifies important information not related to injury, but
possible property damage.
SAFE TY
Indicates steps or instructions for safe practices, reminders of
safe procedures, or important safety equipment that may
be necessary.

iii
Table Of Contents 3.0
1.0 Customer Satisfaction ............................................................................. i
1.1 Stealth Commitment............................................................................................ i
2.0 Warnings ..................................................................................................ii
2.1 Warning Labels .....................................................................................................ii
2.2 Limited Liability ..................................................................................................... ii
2.3 Testing ..................................................................................................................... ii
3.0 Table of Contents……………………………………………………………………………….iii
4.0 Parts and Accessories ............................................................................ 1
4.1 Mounting Hardware Parts .............................................................................. 1
4.2 Mounting Hardware Tools ............................................................................. 2
5.0 Installation Instructions ........................................................................ 3
5.1 Installing The Multi/IDPMP Joystick .............................................................3
5.2 Installing The Micro Joystick............................................................................4
6.0 Functioning ............................................................................................ 6
6.1 Addition/Removal Of Link ............................................................................... 6
6.2 Height Adjustment ........................................................................................... 7
6.3 Swivel Link Adjustment ................................................................................... 8
6.4 Joystick Mount Adjustment ......................................................................... 9
6.5 Lateral Adjustment.......................................................................................... 10
6.6 Depth Adjustment........................................................................................... 10
6.7 Replacing The IDCH Belt .............................................................................. 11
6.8 Removing The Collar...................................................................................... 13
7.0 Warranty ............................................................................................... 14
7.1 In Case Of Product Failure............................................................................. 14
8.0 Notes ...................................................................................................... a

1
Parts And Accessories 4.0
Mounting Hardware Parts 4.1
A Collar
B IDCH ARM
C Latch for the IDCH C1 Height Adjustment Latch
C2 Depth Adjustable Track
C3 Lateral Adjustment Track
D Swivel Link for IDCH D1 Swivel Adjustment Handle
D2 M6 Screw
E Niño Link for IDCH E1 M5X.8X20 MM FHS (3)
F Joystick Mount F1 M5X.8X6 MM BHS (2)
G Niño Link For Mount
H 1/4” Wire Clamp
Description
A
B
C1
D
D2
F
F1
G
E
D1
E1
C2
C
H
C3

2
Parts And Accessories 4.0
Mounting Hardware Tools 4.2
1. T-Handles not included
6
5 T-Handle1 2mm T-Handle
3mm T-Handle
4mm T-Handle
6 Phillips Screwdriver Small
Tools Description
5

3
Installation Instructions 5.0
Step 1: Place Multi or IDPMP joystick atop the joystick mount. Match the holes on the
base of the joystick to the holes on the mount.
Step 2: Secure joystick to mount by inserting provided screws through the matching holes.
Step 3: Secure Power Cord via 1/4” clips (H).
Installing The Multi/IDPMP Joystick 5.1
IDPMP-1 / IDPMP-9
IDM-MULTI-9
WARNING
Ensure joystick power cord is fed thru joystick mount cutout, without splicing or kinking.
* USB ports to client’s right side for forward direction.
Standard Configuration.
1A Multi–Mounting M4 x .7x10mm PHS
(included in IDM-Muti-9
accessory pack).
Phillips Screwdriver Small
2A IDPMP–1 / IDPMP–9
Mounting
10-32 x 1/4 BHS
(2)
T-Handle1 2mm T-Handle
1A
2A
* Orient dimple on top of housing, furthest from client for
forward direction.
1A
H

4
Installation Instructions 5.0
Step 1: Loosen and remove screws (F1) from
joystick mount.
Step 3: Slightly loosen M5 x .8 x 6mm BHS and slide Micro joystick through the strap. Tighten
screws with 3mm T-Handle.
*Orient the arrow, on the underside of the joystick, pointing away from the client for standard
configuration.
Step 2: Remove joystick mount from niño link.
Installing The Micro Joystick 5.2
F1
F

5
Installation Instructions 5.0
Step 4: Attach joystick strap mount to niño link with screws (F1) and tighten with
3mm T-Handle.
F1

6
Functioning 6.0
Addition/Removal Of Link 6.1
If additional height is required:
Step 1: Locate the link screw (E1) on the top link. Remove the M5x.8x20mm FHS from the link,
detaching the joystick mount and link nut.
Step 2: Line up holes on link and add the IDCH-Link (E) to open end.
Step 3: Insert link screw (E1) and tighten with a 3mm T-Handle.
Step 4: Remove screw at the top of the new link.
Step 5: Add joystick mount and link nut, lining up all the holes. Insert screw and tighten.
CAUTION
DO NOT OVER TIGHTEN SCREWS. This could cause wearing of screws or joystick threads, causing
the client to lose efficient control.
2
F
5
E1
E

7
Functioning 6.0
SAFE TY
Always have adjustments performed by a trained service technician.
Height Adjustment 6.2
Add links to adjust height before determining if the arms should be cut. If there are no other
options follow the steps below.
Step 1: Loosen and remove the M3 x .5 x 12mm FHS with the 2mm T-Handle to remove the collar.
Determine the correct height of the mount that is needed for the user.
Step 2: Once the desired height has been determined, make cuts on the arms (B). Adjustments to
the height of the arms should only be made in 1/2” increments.
Step 3: Snap the arms back into the latch (C). Using the 2mm T-Handle, tighten the
M3 x .5 x 12mm FHS back into place.
CAUTION
After cutting adjustments for the arms, smooth all sharp edges.
NOTICE
Cutting the arms should be done only as a last resort. Cuts on the arms need to be
made on the hole below the desired mount location. Ensure cut is made through the
middle of the hole.
C
C
B

8
Functioning 6.0
Swivel Link Adjustment 6.3
Step 1: Turn the handle (D1) in a downward direction to unlock and adjust.
Step 2: Orient to desired angle of client’s needs.
Step 3: Turn handle (D1) in an upward direction to lock into place.
30°
D1
+ OF ADJUSTMENT
Lock

9
Functioning 6.0
Joystick Mount Adjustment 6.4
CAUTION Do not over tighten.
To adjust the angle of the Multi or IDPMP joystick mount:
Step 1: Loosen screw (E1) on niño link nut (E).
Step 2: Adjust Joystick mount (F) to desired angle and tighten screw (E1) with 3mm T-Handle.
F
E1
E + OF ADJUSTMENT

10
Functioning 6.0
3.25 in.
8.15 cm
Depth Adjustment 6.6
Lateral Adjustment 6.5
Step 1: Loosen M5x.8x12mm FHS on track
and position lateral track to desired
location on horizontal track (C3).
Range of adjustment depends on size
of control harness.
Step 2: Tighten screws when track is
in the correct location using
the 3mm T-Handle.
Step 1: Loosen screw (D2). Move the
swivel mount to the desired
location along the track (C2).
Step 2: When the mount is in the
desired location along the
track, tighten the screw (D2)
using the 4mm T-Handle.
Minimum 3 in. to max 6 in. adjustment
depending on collar size
D2
C2
C3
C2
* Depth adjustment does not vary per size.

11
Functioning 6.0
Replacing The IDCH Belt 6.7
C1
B
Step 1: Unscrew and remove M3 x .5 x 12mm FHS
with the 2mm T-Handle. Separate arms (B)
from latch (C1).
Step 2: Loosen and remove the M5 x .8 x
20mm FHS (2) from the i-Drive
latch (top).
Step 3: Separate the latch from the track. Pull
straight upward.

12
Functioning 6.0
6
Step 4: Remove buckles off of pins. Replace new
buckles by sliding 3/8” webbing onto pins.
Match holes of the track to the holes of the
latch, and snap back together.
5
Step 5: Give a slight tug to female buckle
to ensure webbing is hooked onto
slotted spring pin. Insert M5 X 0.8 X
20mm FHS (2) and tighten.
Step 6: Snap the arms back into the latch (C1).
Using the 2mm T-Handle, tighten the
M3- .5 x 12mm FHS screws back into place.
C1

13
Functioning 6.0
Removing The Collar 6.8
The track can be released from the collar (Client’s perspective).
Step 1: For your safety, unbuckle the belt from collar.
Step 2: Chose the direction to release the arms from the latch.
Step 3: Place a firm hold on the latch and arm.
Step 4: Pull latch away from client.
Step 5: Secure and turn latch.
Step 6: Remove from around the neck.
Three (3) different options are available to remove the arms from the latch;
left, right, or a full release.
(Swing to client’s right side) (Swing to client’s left side)

14
Warranty 7.0
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a particular
purpose, shall not extend beyond the duration of this warranty. Stealth
Products, LLC does not warrant damage due to, but not limited to:
Misuse, abuse, or misapplicaon of products.
Modicaon of product without wrien approval from Stealth Products, LLC.
Any alteraon or lack of serial number, where applicable, will automacally void
this warranty.
Stealth Products, LLC is liable for replacement parts only.
Stealth Products, LLC is not liable for any incurred labor costs.
No person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
Stealth Products warrants against failure due to defective materials
or workmanship:
Covers: 2 years
Hardware: 5 years
Electronics: 3 years
In Case of Product Failure 7.1
In the event of product failure covered by our warranty, please follow the
procedures outlined below:
1. Call Stealth at [phone] or toll free [phone].
2. Request the Returns Department or obtain an RA from the Returns Department and follow
department or documentaon instrucons.

a
Notes 8.0

Stealth Products, LLC. • [e-mail] • www.stealthproducts.com
[phone] | [phone] | 104 John Kelly Drive, Burnet TX 78611
P132D400 Revision Date 2019-12-17