Stealth Products Pelvic Support User manual

USER MANUAL
Pelvic Support
The World’s Best Adductors
Stealth’s User Manual and Maintenance Guide for
The World’s Best Adductors

i
Customer Satisfaction 1.0
Stealth Products strives for 100% customer satisfaction. Your complete
satisfaction is important. Please contact us with feedback or suggested changes
that will help improve the quality and usability of our products.
You may reach us at:
General
Read and understand all instructions prior to the use of the product. Failure to
adhere to instructions and warnings in this document may result in property
damage, injury, or death. Product misuse due to failure of the following
instructions will void the warranty.
Immediately discontinue use if any function is compromised, parts are missing,
loose, or shows signs of excessive wear. Consult with your supplier for repair,
adjustment, or replacement.
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
Stealth Products, LLC
104 John Kelly Drive, Burnet, TX 78611
Phone: [phone] Toll Free: 1(800) 965-9229
Fax: [phone] Toll Free: 1(800) 806-1225
[email protected] www.stealthproducts.com

ii
Important Information 2.0
Important Information!
All persons responsible for fitting, adjustment, and daily use of the devices
discussed in these instructions must be familiar with and understand all safety
aspects of the devices mentioned. In order for our products to be used
successfully, you must:
Read and understand all instrucons and warnings.
Maintain our products according to our instrucons on care and maintenance.
Devices should be installed and adjusted by a trained technician.
Supplier Reference
Supplier:
Telephone:
Address:
Purchase Date:
Model:

iii
Introduction 3.0
Before you install or begin using this product, it is important that you read and
understand the content of these installation and operating instructions. The
installation instructions will guide you through the possibilities with
The World’s Best Adductors.
Instructions are written with the expressed intent of use with standard
configurations. They also contain important safety and maintenance
information. For further assistance, or more advanced applications, please
contact your supplier or Stealth Products at [phone] or toll free at
1-800-965-9229.
Always keep the operating instructions in a safe place so they may be
referenced as necessary.
All information, pictures, illustrations, and specifications are based on the
product information that was available at the time of printing. Pictures and
illustrations shown in these instructions are representative examples and
are not intended to be exact depictions of the various parts of the product.
Ordering Documentation
You can download additional copies of this User Manual on the Stealth website:
https://stlpro.site/stealth-docs
and search The Worlds Best Adductors User Manual in the search bar at the top
of the page.

iv
Warranty 4.0
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a particular
purpose, shall not extend beyond the duration of this warranty. Stealth
Products, LLC does not warrant damage due to, but not limited to:
Misuse, abuse, or misapplicaon of products.
Modicaon or product without wrien approval from Stealth Products, LLC.
Any alteraon or lack of serial number, where applicable, will automacally
void this warranty.
Stealth Products, LLC is liable for replacement parts only.
Stealth Products, LLC is not liable for any incurred labor costs.
No person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
Stealth Products warrants against failure due to defective materials
or workmanship:
Covers: 2 years
Hardware: 5 years
Electronics: 3 years
In Case of Product Failure
In the event of product failure covered by our warranty, please follow the
procedures outlined below:
1. Call Stealth at [phone] or toll free [phone].
2. Request the Returns Department or obtain an RA from the Returns Department and
follow department or documentaon instrucons.

v
Table of Contents 5.0
1.0 Customer Satisfaction............................................................................. i
2.0 Important Information .......................................................................... ii
3.0 Introduction ........................................................................................... iii
4.0 Warranty ................................................................................................. iv
5.0 Table of Contents ................................................................................... v
6.0 Warning Labels ...................................................................................... vi
6.1 Warning Labels.................................................................................................... vi
6.2 Limited Liability ................................................................................................... vi
6.3 Testing..................................................................................................................... vi
7.0 Functioning.............................................................................................. 1
7.1 Operating Adductors ......................................................................................... 1
7.2 Adjusting Adductors........................................................................................... 1
8.0 Mounting ................................................................................................. 2
8.1 Standard Track Mounting ................................................................................ 2
8.2 Standard Cane Mounting................................................................................. 2
8.3 Standard Planar Mounting............................................................................... 3
8.4 All Season Mounting.......................................................................................... 3
8.5 Full Surface Contact Mounting ...................................................................... 4
9.0 First Time Use.......................................................................................... 5
9.1 Dealer Assistance................................................................................................. 5
9.2 User Testing ........................................................................................................... 5
9.3 Conditions of Use ................................................................................................ 5
10.0 Maintenance.......................................................................................... 6
10.1 Cleaning................................................................................................................ 6
10.2 Maintenance ....................................................................................................... 6

vi
Warning Labels 6.0
Warning Labels 6.1
Warnings are included for the safety of the user, client, operator and property.
Please read and understand what the signal words SAFETY, NOTICE, CAUTION,
WARNING and DANGER mean, how they could affect the user, those around
the user, and property.
Limited Liability 6.2
Stealth Products, LLC accepts no liability for personal injury or damage to
property that may arise from the failure of the user or other persons to follow
the recommendations, warnings, and instructions in this manual.
Testing 6.3
Initial setup and driving should be done in an open area free of obstacles until
the user is fully capable of driving safely.
The World’s Best Adductors should be adjusted with the user in the chair in
order to promote the best position and maximum comfort for the client.
NOTICE
Identifies important information not related to injury, but
possible property damage.
SAFETY
Indicates steps or instructions for safe practices, reminders of
safe procedures, or important safety equipment that may be
necessary.
CA UTIO N Identifies a potential situation which (if not avoided) will
result in minor to moderate injury,and property damage.
WARNIN G Identifies a potential situation which (if not avoided) will
result in severe injury, death,and property damage.
DANGER Identifies an imminent situation which (if not avoided) will
result in severe injury, death,and property damage.

1
Functioning 7.0
Operating Adductors 7.1
To operate the adductors:
1. Depress the quick release buon (A).
2. The adductor will swing away 180° into an open-locked posion.
3. Depress quick release buon again to return swing away arm to the closed-locked posion.
Adjusting Adductors 7.2
Standard adductors offer three points of adjustment.
To adjust angles (B) and (C):
1. Lightly loosen 1/4-20 x 1” screws.
2. Set desired angles and reghten screws with 3/16 T-Handle. Do not overghten.
To adjust pad height:
1. Loosen 1/4-20 x 5/8” Buon Head Screws (D).
2. Slide the pad into the desired posion.
3. Reghten screws. Do not overghten.
NOTICE
To adjust links, use a 5/32 T-Handle.
(D)
(A)
(B), (C)
Torque Specifications:
1/4-20 screws = 6.3lb-ft

2
Mounting 8.0
Standard Track Mounting 8.1
To adjust standard track mounting:
1. Insert the 1/4 20x 3/4 Socket Head Screws (E) through the counter bore holes (F) and into
the threaded holes of the Universal Track Nut (G).
2. Tighten with a 3/16 T-Handle.
Standard Cane Mounting 8.2
To adjust standard cane mounting:
1. Insert the 1/4-20 x 3/4 Socket Head Screws (H) into the male tube clamp through the
counter bore holes and into the female side of the tube clamp.
2. Aach lateral by using 1/4-20 x 3/4 Socket Head Screws and mounng directly to the cane
clamp.
3. Tighten with a 3/16 T-Handle.
(D)
(E)
(G)
(F)

3
Mounting 8.0
Standard Planar Mounting 8.3
To install planar mounts:
1. Use 1/4-20 x 5/8 Socket Head Screws (A) to mount on the base of the planar mount to the
interior of the adductor.
2. Screw the 1/4-20 x 5/8 Buon Head Screws (B) through the slots on the planar mount onto
the mounng hardware on the chair.
3. Tighten with 3/16 T-Handle.
All Season Mounting 8.4
To install the All Season Mounts:
1. Aach the All Season Bracket to the chair by using the 1/4-20 x 1/2” Flat Head Screws (A).
Tighten with 5/32 T– Handle.
2. Use the 1/4-20 x 3/4 Socket Head Screws (B) to directly mount the All Season Bracket.
Tighten with a 3/16 T-Handle.
3. Press down on the red buon (C) to make lateral adjustments.
(A) (B)
(B
((A)
(C)
(B)
Torque Settings:
1/4-20 screws = 6.3lb.-ft
Torque Settings:
1/4-20 screws = 6.3lb.-ft

4
Mounting 8.0
Full Surface Contact Mounting 8.5
The Full Surface Contact mounts are pre-assembled before they are delivered.
To adjust the angle of the pad mount:
1. Loosen the 10-32 x 1/2” Socket Head Screws with a 3/16 T-Handle.
2. Adjust pad mount to desired angle and reghten screws.
(A)
Torque Settings:
10-32 screws = 31.7lb.-in

5
First Time Use 9.0
Dealer Assistance 9.1
During first time use by the client, it is advised that the dealer or service
technician assists and explain the configuration to the customer (the user
and/or the attendant). If needed, the dealer can make final adjustments.
User Testing 9.2
It is important that the customer is fully aware of the installation and how the
adductors can be adjusted in order to gain the best positioning possible. As a
dealer, proceed as follows:
Explain and show the customer how you have executed the installaon, and explain
the funcon.
Have the user test the position of the adductors:
Are the adductors in the proper posion for the client?
Can the user safely operate the chair in the posion they are seated in?
Is the placement of each of the adductors in an opmal posion for the user?
If needed, adjust the adductors to the proper position.
Explain to the customer any possible issues and how to address them.
Conditions of Use 9.3
The World’s Best Adductors are intended for use as installed by the dealer, in
accordance to the installation instructions in this manual:
The foreseen condions of use are communicated by the dealer or service technician to
the user and/or aendant during the rst me use.
If the condions of use change signicantly, please contact your dealer or a qualied
service technician to avoid excessive wear and tear or unintended damage.
WARNIN G
The adductors should only be fitted by a qualified healthcare professional.
(B)

6
Maintenance 10.0
Cleaning 10.1
To wash the covers of the adductors:
Remove the pad/cover from the adductors
Machine wash in cold water on delicate cycle and drip dry
To wash sheepskin covers:
Remove the cover from the laterals
Machine wash in cold water on delicate cycle (or dry clean), and dry.
Maintenance 10.2
Periodically check the hardware for loose screws or worn areas
Check the pad/cover for any breakdown
Gently remove dust and dirt with a damp cloth
Periodically add anti-seize to the components every 6 months
or as needed.
WARNIN G Do not use bleach.
WARNIN G Do not iron.
SAFETY Replace or repair parts as needed.

a
NOTES 11.0

b
NOTES 11.0

Stealth Products, LLC. • [e-mail] • www.stealthproducts.com
[phone] | [phone] | 104 John Kelly Drive, Burnet TX 78611
P91D275 Revision Date 2019-12-17