Steamfast SF-767 User manual

CORDLESS STEAM IRON
OWNER’S GUIDE
MODEL: SF-767

2 |ENGLISH
READ ALL INSTRUCTIONS BEFORE
USING
IMPORTANT SAFETY INSTRUCTIONS
This owner’s guide and any additional inserts are considered part of the product.
They contain important information about safety, use, and disposal. Before using the
product, please familiarize yourself with all operating and safety instructions. Please
keep all documents for future reference and pass these documents on, together with
the product, to any future owner. See steamfast.com to view, download, and print the
most current version of this owner’s guide.
When using an iron, basic precautions should always be followed, including:
INTENDED USE: Use appliance only for its intended use. This product is intended to
be used indoors for steam ironing in the United States. This product is not intended
for commercial or industrial use. The manufacturer assumes no responsibility for
damage or injury due to unauthorized use or product modication. Failure to follow
these directions will void the product warranty.
WARNING: Risk to Children and Impaired Persons
Supervision is required during the installation, operation, cleaning and maintenance
of this product by children 12 years of age and younger and anyone with reduced
physical, sensory or mental capabilities. Children should be supervised to ensure that
they do not play with the appliance, its parts and packaging material.
- Close supervision is required for any appliance used by or near near children and
pets. Do not leave the iron unattended while the iron is connected or on an ironing
board.
WARNING: BURN HAZARD - To reduce the risk of burns or injury to persons,
observe the following:
- Use caution when handling this steam unit. Burns could occur from touching hot
metal parts, hot water, or steam. Use caution to avoid contact with hot water when
turning the product upside down to empty the reservoir.
- Avoid contact with the hot metal ironing plate.
- Do not point steam vents at people or pets as serious injury or damage can occur.
- Do not iron or steam articles while wearing. Remove article before using this
appliance.
- To reduce the risk of contact with hot water emitting from steam vents, check

ENGLISH |3
appliance before each use by holding it away from body and operating steam
button. Do not operate unit if steam vents are blocked.
WARNING - To avoid damage to the unit or power cord, and to reduce risk
of re, electrical shock and injury to persons, observe the following:
- Do not use the iron if it has been dropped, if there are visible signs of damage, or if
it is leaking. Shock, re, or injury may occur.
- Do not let the cord touch hot surfaces. Let the iron cool completely before putting
the iron away. Do not wrap cord around the unit, use the cable tie provided for
storage.
- Do not use power cord as handle, allow it to hang over edge of counters, or be
crimped or closed in doors.
- The iron must not be left unattended while it is plugged into any power outlet.
- Always turn the iron OFF before plugging or unplugging the iron from the electrical
outlet. Never pull on the cord to disconnect the iron from the electrical outlet;
instead, grasp the plug and pull on the plug to disconnect the iron.
- A loose t between wall outlet (receptacle) and plug may cause overheating and
distortion of the plug. Discontinue use of the product in this outlet. Contact a
qualied electrician to replace loose or worn outlets.
- To reduce likelihood of circuit overload, do not operate another high wattage
appliance on this same circuit.
- If an extension cord is absolutely necessary, a cord with an ampere rating equal to
or greater than the maximum rating of the iron shall be used. A cord rated for less
amperage can result in a risk of re or electric shock due to overheating. Care shall
be taken to arrange the cord so that it cannot be pulled or tripped over.
- This appliance has a polarized plug (one blade is wider than the other.) To reduce
the risk of electrical shock, this plug is intended to t in a polarized outlet only one
way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t,
contact a qualied electrican. Do not attempt to defeat this safety feature.
- To avoid the risk of electric shock, do not immerse the iron in water or other liquids.
- Always disconnect the iron from the electrical outlet before lling the iron with
water, emptying the water from the iron, and when the iron is not in use. Do not
open water tank cap during use.
- Only use distilled water to ll unit. Do not use cleaning agents or other substances
to ll unit. Cleaning agents and other substances could result in injury or damage to
the unit.
- The iron must be used on a at stable surface. The iron must only be used with the
base provided. When placing the iron on its base, ensure that the surface on which
the base is placed is stable.
- Always allow unit to cool completely (at least 30 minutes) before storing. Place unit
on base when cooling, to avoid heat damage to surfaces.

4 |ENGLISH
SERVICING WARNING—To reduce risk of re, electrical shock and injury to
persons, observe the following:
- Do not operate the iron with a damaged cord, or if the appliance has been
dropped or damaged. To reduce the risk of electric shock, do not disassemble or
attempt to repair the appliance, take it to a qualied service person for examination
and repair. Incorrect reassembly or repair could cause a risk of re, electric shock,
or injury to persons when the appliance is used.
- If Heating Indicator Light does not illuminate when Temperature Control Dial is
turned to a selected heat setting, unit is not operating normally. Immediately
unplug and have unit serviced by qualied service personnel.
- Clean your product regularly, only as is instructed in this manual. Prior to cleaning,
turn off the power on your product and unplug. Do not use gasoline, thinners,
solvents, ammonias or other chemicals for cleaning. Refer to the cleaning
instructions provided.
SAVE THESE INSTRUCTIONS

ENGLISH |5
FEATURES
1IRONING PLATE
Heated, non-stick surface that is used to press fabrics, remove wrinkles and create
creases.
2MAIN BODY
Contains the unit’s internal heating components.
3BASE
Works as a docking and reheating station.
4CARRY CASE
Provides a convenient, portable option for moving and storing the Cordless Steam Iron.
5HEATING INDICATOR LIGHT
Will turn off when the Ironing Plate’s set temperature is reached.
6WATER TANK CAP
Covers the Water Tank ll hole. The Cap will “click” when completely shut.
7WATER TANK
Designed to hold a maximum of 6.09 oz (180 ml) of water.
8CONTINUOUS STEAM SWITCH
Controls the unit’s continuous steam feature. When Switch is in the position, continu-
ous steam is inactivated. When Switch is in the position, continuous steam is activated
9STEAM BURST BUTTON
When pressed, provides a quick, powerful burst of steam for tough wrinkles.
10 STEAM MIST BUTTON
Used for draining water and is the location on the back of the main unit.
11 STEAM MIST OUTLET
The Spray Mist Outlet is where the water exits for the Spray Mist feature.
12 HANDLE
Designed for easy control and navigation of the unit.
13 TEMPERATURE CONTROL DIAL
Select the various Ironing Plate heat settings based on your fabric and to turn the unit
OFF.
14 FILL CUP
Designed to help you easily and consistently ll the Water Tank.
15 POWER CORD STORAGE
Conveniently store the power cord in the Power Cord Storage located in the base (not
shown).

6 |ENGLISH
2
45
6
7
8
910
12
11
1
3
14
13
FEATURES

ENGLISH |7
HOW TO USE
FILLING WATER TANK (FOR STEAM IRONING)
1. Turn off iron and unplug Base.
2. Place unit on a at surface and open Water Tank Cap.
3. Use provided ll cup to ll Cordless Iron with water to MAX ll line on Water Tank. Do not
overll unit.
NOTE: In order to extend the life of your unit and keep it functioning at it’s maximum
potential, it is highly recommended that distilled or de-mineralized water be used in
Water Tank.
Using tap water could result in mineral buildup which could block the steam vents. This
will reduce the effectiveness of this unit and may cause unit to spit or spurt hot water.
Follow cleaning instructions provided.
4. When nished lling Water Tank, close Water Tank Cap. Cap will “click” when completely
shut.
When the water level becomes low:
1. Turn off iron and unplug base. Allow to cool for at least 5 minutes.
2. Follow STEPS 2-4 above.
3. Plug power cord back in and resume ironing as usual.
OPERATING UNIT
Your SF-767 Cordless Iron comes with a built-in Auto-Off Feature. When the Cordless Iron is
placed on the Base and powered on, the iron will automatically shut off if not removed from
Base after 8 minutes.
Always place Iron securely on the Base when not in use. Do not rest Iron on other surfaces
or attempt to stand Iron upright.
Burn Hazard. Do NOT touch the Ironing Plate or surrounding area.
Discontinue use if iron has been dropped and shows visible damage. If visible damage
occurs, do not return iron to base while base is powered on.
STEAM IRONING
1. Follow FILLING WATER TANK procedure.
2. Plug power cord into a convenient electrical outlet.
3. Set the Cordless Iron on the Base, ensuring back of Iron sits ush against base.
4. When Heating Indicator Light turns off, the sole plate has reached it’s set temperature.
NOTE: It is recommended to start with lower temperature rst, as high settings designed
for heavy material can damage delicate fabrics.

8 |ENGLISH
FABRIC TEMPERATURE CONTROL TEMPERATURE REQUIREMENT
Silk Low Temperature
Wool Medium Temperature
Cotton, Linen High Temperature
5. To Produce Steam
• For Continuous Steam: Once the Heating Indicator Light has turned off (indicating
selected Ironing Plate temperature has been reached), remove the Cordless Iron from the
base and move the Continuous Steam Switch to the position. After a few seconds, the
unit will automatically begin to emit steam from the Ironing Plate.
• For Steam Burst: Once the Heating Indicator Light has turned off (indicating selected
Ironing Plate temperature has been reached, remove the Cordless Iron from the base,
leave the Continuous Steam Switch in the position, and press the Steam Burst button.
NOTE: Unit is designed to steam horizontally. Steam ow will stop whenever unit is in vertical
upright position. If unit is leaking excessively in vertical position, check that steam button is
disengaged.
CAUTION: Burn Hazard. Hot steam may temporarily vent when the unit is positioned
vertically.
NOTE: Steam can only be produced when the Ironing Plate temperature is set at or
. Steam cannot be produced at the lowest temperature setting.
6. Continue with steam ironing tasks.
IMPORTANT: The Ironing Plate will maintain its set temperature for an approximate 30
seconds. After 30 seconds, set the Cordless Iron back on the Base to reheat the Ironing
Plate. This will take approximately 7 seconds. The Heating Indicator Light will turn on
when the Cordless Iron is set on the base and after approximately 7 seconds, the light will
turn off indicating the Cordless Iron is reheated and ready for use again.
DRY IRONING
1. Plug power cord into a convenient electrical outlet.
2. Set the Cordless Iron on the Base, ensuring back of Iron sits ush against base.
3. When Heating Indicator Light turns off, the Ironing Plate has reached its set temperature. Be
sure to set Continuous Steam Switch to position to avoid water leakage.
NOTE: Follow the fabric guidance chart to select the appropriate Sole Plate temperature
for your fabric.
4. Continue with steam ironing tasks.

ENGLISH |9
IMPORTANT: The Ironing Plate will maintain it’s set temperature for an approximate 30
seconds. After 30 seconds, set the Cordless Iron back on the Base to reheat the Ironing
Plate. This will take approximately 7 seconds. The Heating Indicator Light will turn on
when the Cordless Iron is set on the base and after approximately 7 seconds, the light will
turn off indicating the Cordless Iron is reheated and ready for use again.

10 |ENGLISH
PROPER STORAGE
Preparing your unit for storage is quick and simple. When you have completed your tasks,
follow the steps listed below.
1. Turn Temperature Control Dial to OFF position. To eliminate the potential for water leakage,
move Continuous Steam Switch to OFF position. Place unit securely on the Base.
2. Unplug the power cord. Allow unit to cool for at least 30 minutes.
3. Once cooled, open Water Tank Cap and drain any remaining water into a sink or tub. Close
Cap when nished.
4. Wipe Main Body and Ironing Plate with a soft cloth lightly moistened with water.
• DO NOT clean Ironing Plate with detergents or descalers.
• DO NOT clean Ironing Plate with abrasive or corrosiveproducts.
• DO NOT submerge unit or hold unit under running water.
5. If desired for storage or moving Cordless Iron, place unit on the base and securely connect
the Carry Case to Base. The clips will “click” into place when securely fastened.
6. Place unit in cool, dry location.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may cause the unit to
spit water, limit the effectiveness and reduce the life of your steamer.
1. Follow STEPS 1-3 under CLEANING & STORAGE section above; however, leave Water Tank
Cap open.
2. Make a mixture of 0.5 oz. distilled water and 0.5 oz. vinegar.
3. Using included Measuring Cup, pour water-vinegar solution into Water Tank. Close Water
Tank Cap.
4. Follow normal steam ironing procedure. Allow unit to steam out full contents of Water Tank.
When nished, turn Continuous Steam Switch to OFF position and place unit securely on
the Base.
5. Allow to cool for 5 minutes, then rell Water Tank with fresh distilled water. Repeat STEP 4
until vinegar odor dissipates.
6. Store unit as normal.
CAUTION: Burn Hazard. Using tap water could result in mineral buildup which could
block the steam outlets, causing this unit to spit or spurt hot water. Follow cleaning instructions
provided.
STORAGE & CARE

ENGLISH |11
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE & SOLUTION
Unit fails to heat up. Base is not plugged in. Plug power cord into electrical outlet.
Household circuit breaker / ground fault interrupter has tripped or blown a
fuse. Reset circuit breaker / ground fault interrupter, or replace fuse. For as-
sistance, contact a licensed electrician.
Temperature Control Dial has not been turned to a heat setting.
Unit is leaking water. The Continuous Steam Switch is in this position, but Temperature Control
Dial is not set to high enough heat setting. Refer to Steam Ironing section for
further instructions.
Water tank is overlled. Do not ll past MAX line.
There is mineral build-up. Refer to MINERAL BUILD-UP section for further
instructions.
Unit is not producing
continuous steam
The Continuous Steam Switch is not set in the correct position. Ensure it is
set to position.
The Temperature Control Dial is not set to high enough heat. Refer to Steam
Ironing section for further instructions.
The Cordless Iron has been left off the base for more than 30 seconds. Place
iron back on the base and wait for 7 seconds for reheat.

12 |ENGLISH
Steamfast, a division of Vornado Air, LLC. Steamfast warrants to the original consumer or pur-
chaser this Steamfast (“Product”) is free from defects in material or workmanship for a period
of two (2) years from the date of purchase. If any such defect is discovered within the warranty
period, Vornado, at its discretion, will repair or replace the Product at no cost.
For warranty service: Call 1-800-711-6617 or email [email protected] to obtain
a Return Authorization (“RA”). Please have or include your Product’s model number and serial
number, as well as your name, address, city, state, Zip code, email, and phone number when
contacting Vornado for warranty service. To le a contactless warranty claim, visit www.steam-
fast.com/contact
After receiving the RA, ship your Product to: Vornado Air LLC Attn: Warranty & Repair 415
East 13th Street, Andover, KS 67002. For your convenience, please have your model number
and serial number when contacting Vornado with service inquiries. To ensure proper handling,
packages must be clearly marked with the RA number. Packages not clearly marked with the RA
number may be refused at the receiving dock. Please allow 2–3 weeks for warranty service and
return of your Product after the Product is received.
This warranty does not apply to defects resulting from abuse of the Product, modication,
alteration, mishandling, improper maintenance, commercial use or repair or service of the Prod-
uct by anyone other than Vornado; damages which occur in shipment or are attributed to acts
of God. Improper product use, which includes using an external device that alters or converts
the voltage or frequency of electricity, or shipping a Vornado product to a country not intended
for use will void all warranties. Any unauthorized product modication, repair by unauthorized
repair center or use of non-approved replacement parts is not recommended and any conse-
quences will not be covered by support services or product warranties.
The product warranty will be honored only on models that are being used in the country intend-
ed. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. VORNADO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some states
do not allow the exclusion or limitation of incidental or consequential damages, or allow limita-
tions on how long an implied warranty lasts, so the above limitations or exclusions may not ap-
ply to you. This warranty gives you specic legal rights, and you may have other rights that vary
from state to state. The manufacturer assumes no responsibility for damage or injury caused
by failure to follow these instructions, improper product use or unauthorized product modica-
tions. Any such actions will invalidate the product warranty.
All company names and product names are trademarks of their respective owners. ©All rights
reserved. All technical information, data and instructions for the installation, connection and
operation contained in these instructions for use correspond to the latest available informa-
tion at time of printing. The contents of this manual may differ slightly from the actual product.
Observe any additional supplements.
© 2023 Vornado Air, LLC. Andover, KS 67002, U.S. Specications subject to change without
notice. Steamfast® is a trademark owned by Vornado Air, LLC. Manufactured in China.
WARRANTY

CL3-1048 R,-V00
1-800-711-6617 | steamfast.com | [email protected]