emaux FSU-4TP User manual

1
INSTALLATION
* Install filtration system including pump,filter tank and multiport valve.
* The filter system should be installed as close as possibie to the swimming pool and preferably at a level
of 0.50 metres below the surface of the water in the swimming pool. Make sure there is drainage available
at the place where the filter is to be installed.
* PUMP
1.Only qualified,licensed personnel should install pump and wiring.
2.Electrical Contractors Please Note:All 110 volt 60Hz pump must be wired to the main power supply
trough an approved and correctly rated contractor.
3.Allow for gate valve in suction piping.
4.Pump suction and discharge connections have moulded in
beyond these stops.
thread stops,do not try to screw pipe in
* FILTER TANK and MULTIPORT VALVE
1.Loading the sand media.Filter sand media is loaded through the top opening of the filter.
a.Loosen the plastic clamps from tank neck.
b.Cap internal pipe with plastic cap to prevent sand from entering it.
c.We recommend filling tank approximately 1/2 way with water to provide a cushion effect when the filter
sand is poured in. This helps protect the under-drain laterals from excessive shock.
d.Carefully pour in correct amount and grade of filter sand.Be sure center pipe remains centered in opening.
Sand surface should be leveled and should come to about the middle of the filter tank.Remove plastic cap
from internal pipe.
2.Assemble filter control valve to filter tank.
a.Insert filter control valve(with O'ring in place)into the tank neck,taking care that the center pipe slips
into the hole in the bottom of the valve.
b.Place two plastic clamps around valve flange and tank neck and tighten just enough so that the valve may
Be rotated on tank for final positioning.
c.Carefully screw pressure gauge(with O'ring in place)into tapped hole in valve body.Do not over-tighten.
d.Connect pump to control valve opening marked PUMP with hose.After connections are made,tighten
clamps with screwdrive,tapping around clamp with screwdrive handle to help seat valve flange clamp.
3.Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections,suction lines to pump,waste,etc.
4.To prevent water leakage,be sure all pipe connections are tight.
FILTER & PUMP COMBO
Installation & Operating
Instruction
EMFS14122972
4
By-passes filter for circulating water to pool
Used after backwash to flush dirt from valve
Cleaning Filter by reversing the flow
By-passes filter, used for vacuuming to waste or lowering water level
CLOSED Shuts off all flow to filter or pool
RECIRCULATE
WASTE
RINSE
BACKWASH
FILTER
Valve Position
Normal Filtration and Vacuuming
Function
THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING
SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE
SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO
BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE
TURN PUMP OFF BEFORE CHANGING VALVE POSITION.
WARNING
!
!
TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM,
CLEAN PUMP STRAINER AND SKIMMER BASKETS REGULARLY.
!
DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.
!
EM-VALVE FOR "ULTRA" REPLACEMENT PARTS
FSU-4TP FSU-4P FSU-6TP FSU-6P FSU-8TP FSU-8P
1
2
3
4
5
6
7
89
10
11
12
13
Key No.
Part No.
Product Description
Qty
1
01013130
Handle for 1.5"4-way Valve
1
2
03018160
Pin for handle
1
3
01013131
Fixation for 1.5"4-way Valve Handle
1
4
03011003
￠4*12 Self-drilling screw
3
5
01013132
Pressing Ring
1
6
01181060
Washer for 1.5"4-way Valve Handle
1
7
02011095
O-Ring for Rotor
2
8
02311010
Spider Gasket
1
9
06021014
Plastic pressure gauge With O-Ring (28Psi)
1
10
01013134
1.5"4-way Valve Body
1
11
89280104
Sight Glass with O-Ring
1
12
01013137
1.5"4-way Valve Rotor Connector
1
01013133
Rotor for 1.5"4-way Valve
1
01013135
Diffuserfor 1.5"4-way Valve
1
13
02011184
O-Ring for Diffuser
1

2
REPLACEMENT PARTS OF FILTER
1. Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal,
3. Prime and start pump. Never tun pump dry! Running pump dry may damage seals,causing leakage and flooding!
Fill pump with water before starting motor. (be sure all suction and return lines are open), allowing the filter tank
to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial
back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand media.
4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about
normal filter mode, filtering dirt particles from the pool water.
5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under filter and control
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
INSTALL/START-UP OF FILTRATION
always depress handle before turning.)
1/2 to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
connections, bolts, nuts, as required.
pump and general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation in the
filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher than the
heavy initial dirt load in the water.
valve functions).
AMU PUMP REPLACEMENT PARTS
Release all air from filter and piping system.
In a flooded suction system (water source higher than pump), pump will prime itself when suction and
discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove trap cover; fill trap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace trap cover on trap; turn clockwise to tighten cover.
NOTICE: Tighten trap cover by hand only .Pump should prime now. Priming time will depend on vertical
length of suction lift and horizontal length of suction piping.
PRIMING PUMP
26
25
23
22
20
21
5
27
19
18
17
16
15
14
13
12
11
10
9
8
7
6
4
3
2
124
28
WARNINGS:
I
IIf the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard;
IThis appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety; children should be supervised to
ensure that they do not play with the appliance;
IThe maximum total head is 1 metre;
IPollution of the liquid could occur due to leakage of lubricants;
IThe pump must not be used when people are in the water;
IThe pump must be supplied through a residual current device(RCD) having a rated residual operating
current not exceeding 30 mA.
EMAUX pumps must be wired to the main supply through an approved and licensed electrician.
!
3
15
3
2
14
11
6
2
13
16
17
12
11
1
10
9
8
5
7
6
5
4
2
1
Item No.
Part No.
Descrip ti on Englis h
Qty
1
01013051
32mm & 38mm Adaptor
3
2
02020013
O-Ring
4
3
88281105
4 Way Valve
1
4
01013047
Hose adaptor
1
5
02011026
Sleeve for Hose
2
6
01013046
Nut for Hose
2
7
01370011
Hose
1
8
01013049
Hose adaptor with nut
1
9
02011104
O-Ring
1
10
88028519
AMU012TP AQUA-MINI Pump(with timer & pre-filter)
1
88027919
AMU012P AQUA-MINI Pump(with pre-filter)
1
88028520
AMU016TP AQUA-MINI Pump(with timer & pre-filter)
1
88027920
AMU016P AQUA-MINI Pump(with pre-filter)
1
88028501
AMU020TP AQUA-MINI Pump(with timer & pre-filter)
1
88027901
AMU020P AQUA-MINI Pump(with pre-filter)
1
11
89033601
Pump Assembly Screw
1
12
01111105
Combo Base
1
13
06021014
Plastic Pressure Ga uge With O-Ring (28p si)
1
14
89033602
Clamp Lock with Screw s & Nut
1
15
02010045
O-Ring
1
16
01331061
13" Filter Tank
1
17
89033603
Lateral Assembly wi th Center Pipe
1
Item No.
Part No.
Description English
Qty
Item No.
Part No.
Description English
Qty
1
01021067
Nut for lid
1
14
01021069
Flange
1
2
89280105
1.5"union (optio nal）
2
15
01021068
Nut for body
1
01013015
1.5"Connector (f or input）
1
16
02011156
Motor Slinger
1
01013051
32-38 Union ( opti onal）
2
17
03011067
Screw for flange
4
3
02011104
O-Ring for 1.5" Union
2
18
04021204
Motor(AMU012TP /AM U012P)(110V/60HZ)
1
02020013
O-Ring for 32-38 Union
2
04021204
Motor(AMU016TP /AM U016P)(110V/60HZ)
1
4
01041045
Transparent Lid
1
04021205
Motor(AMU020TP /AM U020P)(110V/60HZ)
1
5
02020049
O-Ring for lid
1
19
01321019
Fan Cover
1
6
01111104
Basket
1
20
04016043
Capacitor for AMU012TP/AMU012P & AMU016TP/AMU016P (110V/60HZ)
1
7
01021070
AMU pump body
1
8
02020014
O-Ring
1
21
02020048
Cover Slinger
1
9
01111017
Drain Plug
1
22
03011007
Screw for cable Box
4
10
01111103
Diffuser
1
23
01321018
Cable Box
1
11
01311051
Impeller(AMU012TP/AMU012P)(110V/60HZ)
1
24
02020012
Slinger for cable Box
1
01311045
Impeller(AMU016TP/AMU016P)(110V/60HZ)
1
25
04015041
PCB (for AMU01 2TP AMU016TP AMU020TP )
1
01311046
Impeller(AMU020TP/AMU020P)(110V/60HZ)
1
26
03011100
Screw
4
12
04015002
1/2″Mechanical seal
1
27
01111102
Base
1
13
02020011
O-Ring for flange
1
28
03011006
Screw for base
1