STI Select-Alert STI-SA5000 Series User manual

Select-Alert
Mini Controller
STI-SA5000 SERIES
Features
· Use as a cabinet alert, door alert,
link with push button/switch or as a
burglar alert.
· Independent strobe and siren timing
of 15 seconds, 30 seconds, 60
seconds or continuous.
· Durable, polycarbonate construction.
· Includes ten high intensity LEDs.
· Sirenoers32userselectabletones.
· Choose piercing 100 or 85 dB alert.
· For indoor use only.
· Available with amber, green, blue,
red or white lens.
· Includes a tamper switch which
triggers the alert when unit is
being removed from a wall.
· Low battery indicator.
· Powered by a 9 VDC battery
(notincluded)orexternal12–24
volts.
· One Form “C” dry relay contact
output.
We protect the things that protect you.®

- 2 -- 2 -
CONTENTS
Warnings and Cautions ................................................................................ page 3
Warranty Information .................................................................................... page 3
Dimensions................................................................................................... page 3
Specications ............................................................................................... page4
Electronic Setup ........................................................................................... page4
Alert Tones ................................................................................................... page 5
Alert Timing and Volume ............................................................................... page 5
Terminal Strip Connections ........................................................................... page 6
Mounting Options......................................................................................... page 6
Electronics Final Assembly............................................................................ page 8
SELECT-ALERT ASSEMBLY PARTS LIST
1 - E05000 Electronics Assembly
1 - M05050* Color Lens * (A, B, G, R, W)
4 Screw#6x5/8in.
4 Screw#8-32x3/8in.
2 Screw#6x11/4in.
2 Anchor#8-10
2 Screw#6-32x11/2in.
1 #8-32x1/2in.tamperscrew
1 - H19016 Tamper wrench
ACCESSORIES
KIT-71100A-W Backbox kit
KIT-E18151 N.C. reed switch and magnet
KIT-SA505 Keyswitchmountingbracket(includeskeyswitch&2keys)
KIT-H18075 Additionalreplacementkey,setof2
KIT-H19016 TamperWrench,setof2

- 3 -
WARNINGS
All units are recommended for indoor use. Unit must be tested periodically to
verify the life of battery. STI recommends you change the 9 Volt battery twice
a year. When purchasing a Select-Alert, you will need to periodically test the
connectionstomakesureaudiblesfunctionatasoundleveltoalertsta.Installer
may need to purchase a simple audio-meter, typically available at your local
electronics store, to measure the sound in areas where the alert is expected to
be heard during normal noise environment. Results from this test may prove it
benecialtopurchaseadditionalSelect-Alertunits.
Allspecicationsandinformationshownarecurrentasofpublicationandsubject
to change without notice.
DIMENSIONS
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**
MAIN POWER
CONTROL
STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**
MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
ACTIVE
WARRANTY
WARNING: This product can expose you to chemicals including Dichloromethane, which
is known to the State of California to cause cancer, and Bisphenol A (BPA), which is
known to the State of California to cause birth defects or other reproductive harm. For
more information go to www.P65Warnings.ca.gov.
Three year warranty or a one year limited warranty (from date of purchase) on most products.
See website for details. Electronic warranty form at www.sti-usa.com/wc14.

- 4 -
SPECIFICATIONS
Operating Voltage Internal power 9 VDC battery (not included)
Operating Temperature 32°F-120°
Power Consumption Stand by: 50µA
Siren low volume: 85mA
Siren high volume: 90mA
  Strobe:25mA
Siren Volume Low: 85 dB
High: 100 dB
Alert Timing Independent control for siren and strobe:
15s, 30s, 60s, continuous
Low Battery Warning LEDashonceevery30seconds
Form C Dry Contacts 0-30VAC/DC, 1 Amp
Contacts reset after longest alert setting
Key Switch Alarm on: normally closed
Alarm Switch Stand by: normally open contact required
Polycarbonate UL94V-2
Flammability Rating
INSTALLATION
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
INSTALLED
BASE PLATE
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
#801 KEY, KIT-H18075
SET OF TWO (2)
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
BASE PLATE
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED SWITCH
FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
S1
ALERT TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
JUMPER WIRE
WIRES TO SIREN
DRILL (4) 3/16 in. DIA. HOLES IF
USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 x 5/8 in. SCREW
(2) PROVIDED
DETAIL A
BASE PLATE

- 5 -
Step 3 - Alert Timing and Volume - S2
1
ALERT TIMING VOLUME
STROBE TIMING
ON
OFF
2345
15 seconds 1 1 1 1 High
30 seconds 1 0 1 0 1
60 seconds 0 1 0 1 Low
Continuous 0 0 0 0 0
Alert Siren Strobe Volume
Timing 1 2 3 4 5
1 = ON 0 = OFF
Factory default settings
Step 2 - Alert Tones - S1
1 0 0 0 0 0 BUZZ
2 1 0 0 0 0 SLOW ON/OFF
3 0 1 0 0 0 SLOW SIREN
4 1 1 0 0 0 3 BEEP/PAUSE/REPEAT
5 0 0 1 0 0 UFO FAST
6 1 0 1 0 0 FAST SIREN
7 0 1 1 0 0 #5 FAST
8 1 1 1 0 0 #2 MEDIUM
9 0 0 0 1 0 #5 MEDIUM
10 1 0 0 1 0 SWOOP MEDIUM
11 0 1 0 1 0 #3 MEDIUM
12 1 1 0 1 0 BUZZ TONE
13 0 0 1 1 0 STEADY FAST
14 1 0 1 1 0 SWOOP SLOW
15 0 1 1 1 0 CONTINUOUS
16 1 1 1 1 0 FAST REPEAT
17 0 0 0 0 1 STANDARD Alert
18 1 0 0 0 1 #3 FAST
19 0 1 0 0 1 #5 SLOW
20 1 1 0 0 1 FAST BEEP
21 0 0 1 0 1 SOUND A
22 1 0 1 0 1 SOUND B
23 0 1 1 0 1 SOUND C
24 1 1 1 0 1 SOUND D
25 0 0 0 1 1 SOUND D LOUD
26 1 0 0 1 1 SOUND E
27 0 1 0 1 1 SOUND F
28 1 1 0 1 1 SOUND G
29 0 0 1 1 1 SOUND H
30 1 0 1 1 1 #4 LOW
31 0 1 1 1 1 SOUND K
32 1 1 1 1 1 CONTINUOUS FAST
1 2 3 4 5 1 2 3 4 5
NOTE: Sound may be disabled by
clipping wires to the siren.
THIS WILL VOID ALL
WARRANTIES. Remove two
screws on circuit board; leave
enough length of wire to possibly
reattach in the future. Then
insulate wires to prevent shorting
to electronic components.
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
INSTALLED
BASE PLATE
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
#801 KEY, KIT-H18075
SET OF TWO (2)
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
BASE PLATE
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED SWITCH
FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
S1
ALERT TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
JUMPER WIRE
WIRES TO SIREN
DRILL (4) 3/16 in. DIA. HOLES IF
USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 x 5/8 in. SCREW
(2) PROVIDED
DETAIL A
BASE PLATE

- 6 -
Step 4 - Terminal Strip Connections
**Shippedwithjumper
wire installed. Remove
to add key switch or
othermainpoweron/o
switch.
Step 5 - Mounting Options
A) To STI Back Box KIT-71100A-W
1.Using5/32drill,drillthroughthe(4)existingholesinbackbox(oneineachcorner).
2.Placebackboxonwallandmarkthemountingholepositions.
3.Ifusing#8-10anchors,drill3/16dia.holes1in.deepintowallandpressanchor
intohole.Ifusing#6screwsonly,drill3/32dia.holes1¼in.deep.
4.Mountbackboxtowallusing#6x1¼in.screws.
5.Mountbaseplateasshownusing(2)#6-32x1in.screws.
Note: If not using STI back box, make sure surface will depress tamper switch.
A
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 X 5/8 in. SCREW
(2) PROVIDED
BASE PLATE
DRILL (4) 3/16 in. DIA. HOLES
IF USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
DETAIL A
“DC IN” are the only polarity sensitive
terminals. When external power is
used, battery will act as a backup. “Dry
Contacts: NC, COM, NO” are used for
remote alert monitoring.
If using power only to trigger
alert,addjumpertothealarm
switch terminals. If not using
key switch or other main
poweron/o,keyswitch
mustalsohavejumper.
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
INSTALLED
BASE PLATE
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
#801 KEY, KIT-H18075
SET OF TWO (2)
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
BASE PLATE
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED SWITCH
FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
S1
ALERT TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
JUMPER WIRE
WIRES TO SIREN
DRILL (4) 3/16 in. DIA. HOLES IF
USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 x 5/8 in. SCREW
(2) PROVIDED
DETAIL A
BASE PLATE

- 7 -
B) To Key Mount Plate or into Wall without Electrical Box
C) To Single Gang Electrical Box
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
INSTALLED
BASE PLATE
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
#801 KEY, KIT-H18075
SET OF TWO (2)
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
BASE PLATE
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED SWITCH
FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
S1
ALERT TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
JUMPER WIRE
WIRES TO SIREN
DRILL (4) 3/16 in. DIA. HOLES IF
USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 x 5/8 in. SCREW
(2) PROVIDED
DETAIL A
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
INSTALLED
BASE PLATE
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
#801 KEY, KIT-H18075
SET OF TWO (2)
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
BASE PLATE
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED SWITCH
FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
S1
ALERT TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
JUMPER WIRE
WIRES TO SIREN
DRILL (4) 3/16 in. DIA. HOLES IF
USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 x 5/8 in. SCREW
(2) PROVIDED
DETAIL A
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
INSTALLED
BASE PLATE
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
#801 KEY, KIT-H18075
SET OF TWO (2)
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
BASE PLATE
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED SWITCH
FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
S1
ALERT TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
JUMPER WIRE
WIRES TO SIREN
DRILL (4) 3/16 in. DIA. HOLES IF
USING #8-10 ANCHORS
DRILL (4) 3/32 in. DIA. HOLES
WHEN USING #6 SCREWS ONLY
#8-10 ANCHOR
(4) PROVIDED KIT-SA504
BACKBOX
REMOVE THESE TABS
FROM ALL FOUR CORNERS
#6 x 1 1/4 in. SCREW
(4) PROVIDED
#6-32 x 5/8 in. SCREW
(2) PROVIDED
DETAIL A
BASE PLATE

Printed in USA Inst. Sht. SA5000, Aug2021
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
NO
COM
NC
ALARM SWITCH
KEY SWITCH
DC IN -
DC IN +
FRONT SIDE
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
S1
ALARM TONES
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH
(REAR VIEW)
WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
S1
ALARM TONE
S2
ALARM TIMING
STROBE TIMING
VOLUME
LED QTY 10
LOW BATTERY
INDICATOR LED
TERMINAL STRIP
TAMPER SWITCH WIRE ENTRY
BATTERY
BATTERY CABLE
SIREN
REMOTE POWER IN
12-24 VDC, 125mA
+
-
OFF ON
**MAIN POWER
CONTROL
STAND BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY
OPEN
NORMALLY
CLOSED
COM
DRILL
3/16 DIA HOLES
19018 ANCHOR
#8-10
(2) PROVIDED
19039 SCREW
#6 x 1 1/4 in.
(2) PROVIDED
TO KEY MOUNT PLATE OR INTO WALL
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
SINGLE GANG
ELECTRICAL BOX
#6-32 x 1 1/2 in. SCREW
(2) PROVIDED
TO SINGLE GANG ELECTRICAL BOX
BASE PLATE
05050- LENS COLORS
A - AMBER
B - BLUE
G - GREEN
R - RED
W - WHITE
#8-32 x 3/8 in. SCREW
(4) PROVIDED
05000 ELECTRONICS
ELECTRONICS ASSEMBLY FINAL
INSTALLED
BASE PLATE
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-SA504 BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
TO STI BACKBOX 71100A
71100B-W
BRIDGE INSERT
1 31/32 in.
3 9/32 in.
WIRE ACCESS HOLE
TAMPER-PROOF
TOOL (1) PROVIDED
TAMPER-PROOF SCREW
2 13/32 in.
19018 ANCHOR
#8-10
(4) PROVIDED
DRILL (4)
3/16 in. DIA HOLES
KIT-71100A-W BACKBOX
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19068 SCREW
#6 x 5/8 in.
(4) PROVIDED
BASE PLATE
71100B-W
BRIDGE INSERT
1 31/32 in.
DRILL
3/16 DIA HOLES
ANCHOR
#8-10
(2) PROVIDED
#6 x 1 1/4 in. SCREW
(2) PROVIDED
BASE PLATE
H18074 SWITCH LOCK
KIT-SA505 KEY SWITCH
MOUNTING BRACKET
3 9/32 in.
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
REMOTE POWER IN
12-24 VDC, 125mA
+
-OFF ON
**MAIN POWER
CONTROL
STAND
BY
ALARM
SWITCH
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
1.58 in.
2.725 in.
4.75 in.
4.83 in.
3.05 in.
3.22 in.
3.25 in.
4.83 in.
3.25 in.
(83mm)
4.83 in.
(123mm)
FRONT SIDE
3.25 in.
(83mm)
4.83 in.
(123mm)
1.58 in.
(40mm)
2.73 in.
(69mm)
2.73 in.
(69mm)
LENS COVER
BACKPLATE
MOUNTING PLATE
ELECTRONICS
19011 TAMPERPROOF SCREW
KEY SWITCH
LENS COVER
BACKPLATE
KEY SWITCH
MOUNTING PLATE
19011 TAMPERPROOF SCREW
ELECTRONICS
#801 KEY
#801 KEY
REMOTE POWER IN
12-24 VDC, 125mA
(OPTIONAL)
+
-
OFF ON
**MAIN POWER
CONTROL TO
KEY SWITCH
STAND
BY
REED
SWITCH FROM CABINET
FORM "C"
DRY CONTACTS
NORMALLY OPEN
COM
+ -
DC IN
KEY
SWITCH
ALARM
SWITCH
NC
COM
NO
NORMALLY CLOSED
ACTIVE
DRILL (4) 3/16 in. DIA. HOLES IF USING #8-10 ANCHORS.
DRILL (4) 3/32 in. DIA. HOLES WHEN USING #6 SCREWS ONLY.
19018 ANCHOR
#8-10
(4) PROVIDED
SUB-71100A-W
19039 SCREW
#6 x 1 1/4 in.
(4) PROVIDED
19060 SCREW
#6-32 x 1 in.
(2) PROVIDED
BASE PLATE
1-24-11
NOTE TO BECK:
This sketch replaces
(Step 5 - Mounting Options VIEW A)
in STI-SA5000 install sheet.
1. Using 5/32 Drill, Drill through the (4) exsisting holes in backbox (one in each corner).
2. Place backbox on wall and mark the mounting hole positions.
3. If using #8-10 anchors, drill 3/16 dia. holes 1 in. deep into wall and press anchor into hole.
If using #6 screws only, drill 3/32 dia. holes 1-1/4 in. deep.
4. Mount backbox to wall using #6 x 1 1/4 screws.
5. Mount base plate as shown using (2) #6-32 x 1 in. screws.
NOTE: If not using STI backbox, make sure surface will depress tamper switch.
ENCLOSURE
ROUTE THE TWO KEY
SWITCH WIRES THROUGH
THE HOLE AS SHOWN
WIRE ACCESS HOLE
ROUTE THE TWO REED
SWITCH WIRES FROM
CABINET THROUGH THE
HOLE AS SHOWN
ACTIVE
Step 6 - Electronics Final Assembly
Step 7 - Operation
Wiring: After mounting circuit board assembly, connect wires. Refer to terminal
stripconnections(step4).
Lens installation: Slide lip of lens behind circuit board mounting plate. Rotate
lens into position. Secure with tamperproof screw and special wrench.
• Turn key switch on to arm.
• Cycle key switch to reset alert.
• Alert will sound when cover is removed, unit is removed from the wall or
cabinet is opened (alert switch is electronically closed).
• Toservice,turnkeyswitcho.
Taylor House • 34 Sherwood Road • Bromsgrove, Worcestershire • B60 3DR • England
Tel: [phone] • [email protected] • www.sti-emea.com
Unit 7A • Lockhead Avenue • Airport Business Park • Waterford • X91 HWF2 • Ireland
[email protected] • www.sti-emea.com
2306 Airport Rd • Waterford, MI 48327, USA
Phone: [phone] • [email protected] • www.sti-usa.com