Stirling Black STR-PGGC75 User manual

75cm Glass Gas Cooktop
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Model Number STR-PGGC75
INSTRUCTION MANUAL
E209

2
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Welcome
Congratulations on choosing to buy a STIRLING®product.
All products brought to you by STIRLING®are manufactured to the highest
standards of performance and safety and, as part of our philosophy of
customer service and satisfaction, are backed by our comprehensive
3 Year In Home Warranty. We hope you will enjoy using your purchase
for many years to come.

3
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Contents
02 Welcome
04 Warranty Details
05 General Safety Instructions
08 Product Overview
10 Installation
24 Instructions
28 FAQs & Troubleshooting Guide
29 Other Useful Information
35 Repair and Refurbished Goods or Parts Notice

4
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
75cm Glass Gas Cooktop
Warranty Details
The product is guaranteed to be free from defects in workmanship and
parts for a period of 36 months from the date of purchase. Defects that
occur within this warranty period, under normal use and care, will be
repaired, replaced or refunded at our discretion. The benets conferred by
this warranty are in addition to all rights and remedies in respect of the
product that the consumer has under the Competition and Consumer Act
2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and to compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

5
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
General Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before rst use, even if you are familiar with this
type of product. The safety precautions enclosed herein reduce the risk of re,
electric shock and injury when correctly adhered to. Make sure you understand
all instructions and warnings. Keep the manual in a safe place for future refer-
ence, along with the completed warranty card and purchase receipt. If you sell or
transfer ownership of this product, pass on these instructions to the new owner.
Always follow basic safety precautions and accident prevention measures
when using an electrical appliance, including the following:
WARNING!
• Professional installation only: This cooktop must be installed by a licensed
plumber/gastter in accordance with all instructions in this manual and all
applicable rules and regulations. Any electrical work required for installation
must be carried out by a licensed electrician. Comprehensive installation
instruction follow on pages 10 to 23 of this manual. Ensure to make these
instructions available to the installer, and record their details on page 33. Failure
to install the cooktop correctly could invalidate any warranty or liability claims.
• Electric shock hazard: This appliance must be connected to a good earth
wiring system. Before carrying out any work on the electrical section of
the appliance, or any maintenance work or repairs, the appliance must be
disconnected from the mains. If accessible, always switch off the cooktop at
the wall before cleaning the appliance. Failure to follow this advice may result
in death or electric shock.
• Hot surface hazard: While in use, direct contact with the cooktop surface
may cause burns! Take utmost care when the equipment is in use. Do not
touch the cooktop components (hob, burners, caps, trivets) when hot. We
recommend using oven gloves when handling cookware.
• Fire hazard: Never leave items on top of the cooktop as this can be a re
hazard when switched on. In case of a re, never try to extinguish it with water.
Switch off the burner and cover the ame(s) with a metallic lid or re blanket.
• Explosion hazard: DO NOT USE OR STORE FLAMMABLE MATERIALS
NEAR THIS APPLIANCE OR IN ITS STORAGE DRAWER (if present).
• DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE
IT IS IN OPERATION.
• DO NOT MODIFY THIS APPLIANCE.
• DO NOT USE THIS APPLIANCE AS A SPACE HEATER.
Failure to adhere to the above warnings may result in death or serious injury.

6
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
General Safety Instructions (Cont.)
General usage conditions and restrictions
• Domestic use only: This cooktop is designed for indoor domestic use only;
it is not intended for commercial, industrial or trade use. The cooktop can
be built into a kitchen cabinet or housing unit.
• Intended purpose: Only use this cooktop for its intended purpose, in its
intended environment and as described in this manual. Any other use may
cause re, electric shock or injury, and invalidate the warranty.
• Ventilation: Heat, steam and moisture will be created during use of the
cooktop. Take care to avoid injury and ensure that the kitchen is adequately
ventilated.
• Instructions: Make sure to observe all rules and provisions in this
instruction manual. Do not allow anybody who is not familiar with the
contents of this manual to operate the cooktop. These instructions are
not intended to cover every possible condition and situation. As with any
electrical household appliance, use common sense and caution when
installing, operating and maintaining the cooktop.
• Power cord: Do not allow the power cord to come into contact with areas on
the cooktop that get hot. Check the cord regularly for damage. Do not use the
appliance if the cord or any other part of the appliance has been damaged.
If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualied person in order to avoid a hazard.
• Usage restriction: This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a person responsible
for their safety.
• CAUTION! Children and pets: Cooking appliances become very hot in
use, therefore ensure children and pets are kept away. If it is necessary
for younger family members to be in the kitchen, ensure that they are kept
under close supervision at all times.Do not allow children to operate or play
with any part of the appliance, or sit, stand, or climb on it. Cleaning and user
maintenance shall not be carried out by children without supervision.
• Pots and pans: Do not use unstable cookware, plastic cookware or
aluminium foil containers on the cooktop. Do not let large cookware overhang
the bench as this could deect heat onto the benchtop, which could damage
the surface. Pot and pan handles may become hot during use; position
handles away from the edge of the cooktop and out of reach of children.

7
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
General Safety Instructions (Cont.)
• Marine craft and leisure vehicles: Where this appliance is installed for
use with LPG in marine craft or in caravans, it shall not be used as a space
heater.
• Frying food: When frying food on the cooktop, check constantly and
ensure the oil is not overheating and becoming a re hazard. Do not ll deep
frypans more than one third full of oil. Do not leave unattended.
• WARNING! Fire risk: Never leave the cooktop unattended during use,
as this is a re risk. Oils and fats in pots and pans may catch re due to
overheating. Do not cover the cooktop or place combustible materials on or
near the surface even when the cooktop is not in use.
• No timer: The appliance is not intended to be operated by means of an
external timer or separate remote control system.
• Cleaning: In the interests of safety and hygiene, ensure the cooktop is
kept clean as a build-up of grease could cause a re hazard. Switch off all
controls and allow the cooktop surface to cool before cleaning.
• Cleaning precautions: Disconnect the appliance from the mains before
cleaning, if your setup allows and the plug is accessible. Do not immerse
the appliance or power cord in water or any other liquid. Do not use steam
cleaning equipment for cleaning the cooktop. Do not use scourers or any
other harsh abrasive cleaning agents, as these can scratch the glass.
• Handle with care: Do not place or drop heavy objects on your cooktop.
• Disconnection: Do not disconnect the appliance with wet hands. Grip by
the plug, do not pull by the cord when disconnecting.
• Damage/repair: Do not use the cooktop if any part has been damaged or
does not work properly, or in the event of a technical fault. Any faults must
be xed by an appropriately qualied and authorised person. Incorrect
repair could expose you to the risk of electric shock, re or injury. Prolonged
use of the unit in such conditions could cause re or electrocution. In case
of damage or a technical fault, contact our after sales support centre.
• WARNING! Do not cook on a broken or cracked cooktop! If the surface
is cracked, switch off the cooktop immediately at the mains power supply to
avoid the possibility of electric shock, as glass-ceramic and similar cooktop
surfaces protect live parts. Call for service.
• Misuse: We assume no liability for any eventual damages or injury to
persons caused by misuse of the product or noncompliance with these
instructions.

8
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Scope of delivery
Glass gas cooktop parts
A Semirapid gas burner NG 2x 6.5MJ/h ULPG 6.6MJ/h
B Rapid gas burner NG 10.8MJ/h ULPG 11MJ/h
C Auxiliary gas burner NG 3.6MJ/h ULPG 3.5MJ/h
D Wok gas burner NG 14.4MJ/h ULPG 14.7MJ/h
E Cast iron trivets (pan supports)
F Glass surface
G Control panel (burner control knobs)
From left to right: Left-hand side (wok)
Front centre (auxiliary)
Rear centre (semirapid)
Rear right-hand side (rapid)
Front right-hand side (semirapid)
Product Overview
AB
D
CA
E
E
F
G

9
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Product Overview (Cont.)
NOTE: Due to continued product improvement, images and illustrations in this
manual may vary slightly from the product purchased. All images in this manual are for
reference purposes only. Parts are not necessarily pictured to scale.
Gas burner (5) parts
H Burner caps
I Burner bases
J Ignition spark electrodes
K Flame failure thermocouples
Installation hardware
L Mounting brackets (4)
M Tapping screws (4)
N Sealing tape
O Gas regulator
P ULPG injectors (5) *
Q NG connector
and joint gaskets
Documentation
(not shown):
Instruction manual
Quick start guide
Warranty certicate
I
J
H
K
LM
O
P
N
Q
* The cooktop is configured for use with NG (Natural Gas). The injectors are for
conversion to ULPG (Universal Liqueed Petroleum Gas). Sizes supplied:
1x ∅0.53mm – 2x ∅0.72mm – 1x ∅0.93mm – 1x ∅1.07mm

10
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Installation
Unpacking the appliance
• This product has been packaged to protect it against transportation
damage. Unpack the appliance but keep all packaging materials until you
have made sure your new glass gas cooktop is undamaged and in perfect
condition. If you have any doubts, do not use the appliance and call our
after sales support centre for advice.
• The carton is recyclable. Whenever possible, reuse the carton and recycle
it when disposing of the packaging materials.
• Some parts on the appliance are protected by a plastic film, which must be
removed before the appliance is used. We recommend carefully slitting the
plastic lm along the edges with a sharp knife.
• Plastic wrapping can be a suffocation hazard for babies and young
children, so ensure all packaging materials are out of their reach and
disposed of safely.
WARNING: Professional installation only!
• This cooktop must be correctly installed by an authorised, licensed
gastter/plumber only, in accordance with Gas Installation Code
AS/NZS 5601, all other applicable rules and regulations and all
instructions in this manual. It is in your interest and that of your safety
to ensure compliance.
• Do not try to install the cooktop yourself! Doing so will expose you to
danger and void the warranty. Improper installation, adjustment, alteration
or service can cause injury or damage. We decline any responsibility for
injury or damage, to persons or property, as a result of improper use or
installation.
• This appliance is not connected to a ue for discharge of the
combustion products; therefore, it must be connected in compliance
with the above mentioned installation rules. Particular attention must
be paid to the instructions given on the opposite page for ventilation.
• Any adjustments, conversions and maintenance of this product may
only be carried out by an appropriately authorised person, as mentioned
above.
• The safety and automatic adjustment devices of the appliance may
only be modied by an authorised service agent.

11
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Important installation advice
Natural gas only: The cooktop is configured for use with NG (Natural
Gas). If it is to be used with LPG, it must be converted
using the ULPG (Universal Liqueed Petroleum Gas)
injectors provided and following the conversion
instructions starting on page 18. Such a conversion
must only be carried out by a licensed plumber/
gastter.
Location: The cooktop may be located in a kitchen, kitchen/
dining room or a bed-sitting room, but not in a room
containing a bath or shower. The cooktop must not
be installed in a bed-sitting room of less than 20m3.
If used with LPG, the cooktop shall not be installed
in a room or space below ground level, such as in a
basement.
Heat resistance of Wall and bench surfaces must be capable of
surrounding surfaces: sustaining temperatures of 95°C and be resistant to
heat, steam and condensation. All laminates, xing
adhesive and surfacing materials must be certied
suitable for this temperature.
We assume no liability for any damage caused if the
appliance is installed contrary to this advice.
Do not install the cooktop near curtains or other
ammable materials.
Ventilation This appliance must only be used in rooms equipped
requirements: with adequate ventilation. The use of a gas cooking
appliance results in the production of heat and
moisture in the room in which it is installed. Always
ensure that the kitchen is well ventilated; keep natural
ventilation holes open or install a rangehood.
Prolonged intensive use of the appliance may require
additional or more effective ventilation, for example,
opening of a window or increasing the level of
mechanical ventilation, where present.
Installation (Cont.)



12
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Clearances
The clearances listed below are required when installing the appliance into a
kitchen unit or worktop. For a pictorial overview, please refer to Fig.1 and Fig.2
on the opposite page. The letters in blue in the guidelines below refer to the
clearances marked in Fig.2.
• Fire resistant materials (such as ceramic tiles) are required up to 450mm
above the burner top.
• Walls or vertical structures must be at least 200mm away from the burner.
• Minimum distance from the edge of the closest burner (left and/or right side)
to the nearest vertical combustible surface: 200mm A
• Minimum distance from the edge of the closest rear burner to the
combustible vertical surface: 200mm B
• IMPORTANT! Where the horizontal clearance is less than 200mm, that
vertical surface must be protected by a non-combustible material for a
minimum height of 200mm above the cooktop surface across the entire
length (depth, width). The 200mm protected surface (Fig.1) may be ceramic
tiles or another approved non-combustible material. C
• Minimum height of noncombustible material when used on adjacent walls:
200mm C
• IMPORTANT! Minimum clearance from the top of the highest burner cap to
a rangehood: 600mm D. This also applies to any other ammable objects
such as utentil rails, wall cabinets, shelves, etc.
• Minimum clearance below the top of the benchtop to the nearest
combustible surface: 70mm E
• Ensure there is an earthed power outlet within 900mm of the rear right-hand
corner of the cooktop. The outlet should be accessible with the cooktop
installed. F
• If connecting the cooktop to the gas supply with a exible hose, the
connector on the wall should be between 800–850mm above the oor
and to a distance of at least 250mm outside the width of the cooktop. The
connector should be accessible with the cooktop installed. G
Installation (Cont.)

13
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Installation (Cont.)
Fig. 2
G
F
Fig. 1
200
NOTE: The cooktop illustrated in Fig. 2 varies from the STR-PGGC75 purchased. It is
only intended for illustrative purposes of the required clearances.

14
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Benchtop preparation
• Make sure the kitchen area is dry and there is sufcient ventilation and
easy access to all control elements.
• Do not install the cooktop near curtains or other ammable materials.
• The cooktop can be tted to any benchtop with a thickness of 40–50mm.
• If you have (or plan to have)
a rangehood tted above the
cooktop, check in the rangehood
instructions that you will have the
required clearance before starting
with the installation.
• The required clearances for the
cooktop are illustrated on page 13.
• To install the cooktop in your
benchtop, make an opening with
the dimensions given in Fig. 3.
Installation (Cont.)
Fig. 3
Applying the seal
The installation hardware includes a length of sealing tape, which when applied
around the cooktop prevents liquid from entering the cabinet. Before installing
the cooktop, please apply this sealing tape follow the instructions below.
• Remove the trivets, burner bases and burner caps, then turn the cooktop
upside down and place it on a cushioned mat, taking care not to damage
the ignition spark electrodes and the thermocouples.
• Detach the backing strip from the sealing tape but ensure that the
transparent adhesive still adheres to the seal itself.
• To apply the sealing tape,
correctly position it under
the edge (Fig.4), ensuring
that the outer part of the
seal perfectly matches the
outer edge of the cooktop.
The ends of the strips must
t together without overlapping. Then press the seal rmly in place at the
underside of the cooktop.
• IMPORTANT: Do not use a silicon sealant to seal the appliance against the
aperture. This will make it difcult to remove the cooktop from the aperture
in future, if it needs to be serviced.
Fig. 4

15
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Installation (Cont.)
Installation options
When tting a gas cooktop above a drawer or standard housing unit, suitable
precautions must be taken to prevent contact with the cooktop hob and base,
which become very hot during operation. The recommended method for over-
coming this problem is to x a wooden panel within the cabinet at a minimum
distance of 30mm below the underside of the cooktop (Fig. 5).
NOTE: The panel below the hob must be easily removable to enable servicing if
and when required.
Affixing the cooktop
Once the sealing tape has been installed around the underside of the cook-
top, carefully turn it back over and gently lower it into the aperture hole that
has been cut out. Push it down gently so that the cooktop is resting rmly on
the cabinet/benchtop surface.
• Secure the cooktop in position using the mounting brackets supplied.
• There are four mounting points (1, 2, 3, 4) on the cooktop base to afx the
brackets (Fig. 6).
Fig. 5
30mm (min)
40mm
1
2
3
4
Gas inlet
connection
Fig. 6

16
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Fig. 7
ASealing tape
CScrew BMounting
bracket
Installation (Cont.)
• Put the mounting brackets in the
appropriate locations (as indicated
in Fig.6 on the previous page) and,
using the screws provided, afx the
brackets (Fig.7: B) to the cooktop
and tighten the screws (Fig. 7: C)
securely. This is very important.
• The other side of the bracket must
be located on the underside of the
benchtop, as shown in Fig.7.
Electrical connection
• Connection: The appliance is
equipped with an electrical cord
and power plug, which must be
connected to the mains electricity supply in order for the ignition to work.
Insert the power plug rmly into an appropriate electrical outlet and switch
on power at the outlet.
• Wall socket: The electric wall outlet must be properly earthed and
accessible. It must be suitable for the power drawn by the appliance. The
outlet voltage and circuit frequency must correspond to the voltage stated
on the appliance rating label.
• Power cord: When installing the appliance, make sure that the power
supply cord does not come into contact with any parts of the cooktop that
get hot during use, or with hot cookware. If the supply cord is damaged,
it must be replaced by the manufacturer or a similarly qualied person in
order to avoid a hazard.
• Electrical work:
Should any electrical
work be required asso-
ciated with the electrical
outlet that is to be used
for the cooktop, all such
work must be carried
out by an appropriately
qualied, licensed elec-
trician in accordance
with all applicable rules
and regulations.
序号 修 改 说 明
佛山市沃尔姆斯电器有限公司
审核/
日期
设计/
日期
批准/
日期
工艺/
日期
数量
1
比
例1：1
重量
物料
编码
7654321 7654321
4321 4321 5 76
5 76
88
88
F
E
D
C
B
F
E
D
C
B
AA AA
D
C
B
D
C
B
EE
FF
备注:
1、材质：银底黑字不干胶
2、尺寸：75*45mm
3、字体图案要求清晰、无毛边
4、用酒精擦拭15S，无掉色
5、产品符合rohs要求
亚银龙
五炉头电气原理图
17000149
Fig. 8: Wiring diagram

17
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Installation (Cont.)
Gas connection
• Safety regulation: This cooktop must be correctly installed by an
authorised, licensed gasfitter/plumber only, in accordance with Gas
Installation Code, AS/NZS 5601, all other applicable rules and regulations
and all instructions in this manual. It is in your interest and that of your
safety to ensure compliance. Failure to have the cooktop installed correctly
could invalidate the warranty, liability claims and lead to prosecution.
• Connection parts: The appliance must be connected to the gas supply
by use of a 15mm x ½” female coupler, seal, copper pipe or a flexible hose
(Fig. 9), and an isolation tap fitted in an easily accessible position.
Fig. 9
Gas rail
Seal
15mm x ½” (12.7mm)
female coupler
Fig. 10
• Accessibility: Make sure that it is possible to run gas lines to the gas
connection point of the appliance. The gas connection point must be
accessible without having to remove the cooktop. If a exible hose is used,
the connection point must also be accessible without having to remove the
cooktop.
Dual gas regulator valve
The supplied dual gas regulator valve (Fig. 10) is a low-pressure pipeline
regulator valve, built-in voltage regulator for gas products. It is factory-set
for use with Natural Gas (NG), but can be adjusted for use with Liqueed
Petroleum Gas (LPG).

18
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Installation (Cont.)
Installing the gas regulator
• When installing the gas regulator, ensure that its valve outlet thread
matches the thread of the gas connector.
• Use an appropriate sealant around the threads.
• Ensure that the gas regulator valve installation location is perpendicular.
• After installation, open the gas source switch and check the valve body
connections with soap and water for leaks.
Converting the gas regulator for use with LPG
This cooktop is tted out for use with Natural Gas (NG). If it is to be used with
liqueed petroleum gas (LPG), the gas regulator valve has to be converted.
• Using special tools, open the cover of the gas regulator valve by turning it
anticlockwise (Fig. 11-A, page 19).
• Remove the adaptor from the top cover (Fig. 11-B).
• Pull out the adaptor, invert it and replace the top cover (Fig. 11-C).
• Invert the assembled adaptor’s top cover and replace the regulator valve
(Fig. 11-D).
NOTE: Do not adjust the regulator valve body piece in the above procedure,
otherwise it will affect the performance parameters set in the factory.
WARNING:
• The regulator valve outlet pressure is set at the factory, please do not
adjust it in order to avoid the occurrence of safety accidents.
• If you nd any abnormality of the regulator valve, stop using the appliance
and contact our after sales support centre for advice. Do not attempt any
maintenance yourself.
Table 1: Performance parameters
NG LPG
Operating temperature –20°C to 60°C
Inlet pressure setting 6 in.wc 11 in.wc
Outlet pressure 5±0.3 in.wc 10±0.5 in.wc
Inlet side screw 1/4 NPT
Outlet side screw 1/4 NPT

19
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Installation (Cont.)
Gas adjustment (conversion for use with LPG)
This cooktop is tted out for use with Natural Gas (NG). If it is to be used with
liqueed petroleum gas (LPG), the gas regulator valve and the burners have
to be converted.
IMPORTANT: Before starting the conversion, make sure all gas is
switched off (and preferably disconnected from the appliance) and the
electrical power has been disconnected.
• Remove the trivets, burners, burner crowns and caps (Fig. 12-A).
• Unscrew the injector (Fig. 12-B) and replace it with the stipulated injector
for the new gas supply (see Table 2 on the next page).
Fig. 11-A Fig. 11-B
Fig. 11-C Fig. 11-D
Factory-set state
Fig. 12-A Fig. 12-B

20
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-PGGC75 PRODUCT CODE: 10288 09/2019
Table 2
Regulated for NATURAL GAS ULPG
Injection
∅(mm) MJ/h Gas Pressure
Injection
∅(mm) MJ/h Gas Pressure
Auxiliary 0.85 3.6
1.0 kPa
0.53 3.5
2.75 kPa
Semirapid 1.16 6.5 0.72 6.6
Rapid 1.49 10.8 0.93 11.0
Wok 1.80 14.4 1.07 14.7
Total 41.8 42.4
• Reassemble all the burners carefully; in particular you should make sure
that the burner crown is correctly placed on the burner.
• IMPORTANT: The minimum ow adjustment process must be completed
before the appliance is next used.
Installation (Cont.)
Minimum flow adjustment for hob gas taps
IMPORTANT: Before adjusting the minimum flow of the burners, make
sure all gas is switched off (and preferably disconnected from the
appliance) and the electrical power has been disconnected.
• Remove all the trivets, burner crowns and
caps, and knobs.
• Unscrew the screws of the panel, then
remove the panel.
• Install the burner cap, burner crown and
knob of the burner. Switch the burner on
and set the knob at the minimum position.
• Place a small-bladed screwdriver on the
screw to adjust the minimum ow (as
shown in Fig. 13).
• Unscrew the adjusting screw in order to
increase the gas ow, or tighten it in order
to decrease the gas ow.
• The correct adjustment is obtained when
the ame has a length of about 3–4 mm.
Fig. 13