Streetwize SWIBC4 User manual

Read and understand these instructions before attempting any
operation of this battery charger and retain for future reference!
SWIBC4
6/12V 10Amp Intelligent
Car & Motorcycle
Smart Battery Charger
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 2

2
1
4
965 7
2
8
3
Item Layout & Contents
1. Power Indicator LED (Red)
2. Charged Indicator LED (Green)
3. Charging Indicator LED (Orange)
4. 6V Indicator LED (Orange)
5. Crocodile Clips (+ Red) & (– Black)
6. Voltage Selector Button
7. 12V Indicator LED (Orange)
8. Digital Display Selector
9. 240V Mains 3-pin plug & cord.
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 3

1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
1.1 SAVE THESE INSTRUCTIONS –
This manual contains important safety
and operating instructions.
1.2 Do not expose the charger to rain or snow.
1.3 Use of an attachment not recommended
or sold by the battery charger
electric shock or injury to persons.
1.4 To reduce the risk of damage to electric
plug and cord, pull by the plug rather than
the cord when disconnecting charger.
1.5 An extension cord should not be used
unless absolutely necessary. Use of
improper extension cord could result
extension cord must be used, make sure:
That the pins on plug of extension cord
are the same number, size and shape as
those of plug on charger.
That extension cord is properly wired and
in good electrical condition; and
That wire size is large enough for AC
.
1.6 Do not operate charger with damaged
cord or plug – replace the cord or plug
immediately.
1.7 Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way.
1.8 Do not disassemble charger; incorrect
reassembly may result in a risk of electric
shock or fire.
1.9 To reduce risk of electric shock, unplug
charger from outlet before attempting
any maintenance or cleaning. Turning off
controls will not reduce this risk.
1.10 WARNING: RISK OF EXPLOSIVE
GASES.
a. Working in vicinity of a lead-acid battery
is dangerous.Batteries generate
explosive gases during normal battery
operation.For this reason,it is of utmost
importance that you follow the
instructions each time you use the
charger.
b. To reduce risk of battery explosion,
follow these instructions and those
published by battery manufacturer
and manufacturer of any equipment
you intend to use in vicinity of battery.
Review cautionary marking on these
products and on engine.
2. PERSONAL SAFETY PRECAUTIONS
2.1 Consider having someone close enough
by to come to your aid when you work
near a lead-acid battery.
2.2 Have plenty of fresh water and soap
nearby in case battery acid contacts skin,
clothing, or eyes.
2.3 Wear complete eye protection and
clothing protection. Avoid touching eyes
while working near battery.
2.4 If battery acid contacts skin or clothing,
wash immediately with soap and water.
eye with running cold water for at least
10 minutes and get medical attention
immediately.
2.5
in vicinity of battery or engine.
2.6 Be extra cautious to reduce risk of
dropping a metal tool onto battery. It might
spark or short-circuit battery or other
electrical part that may cause explosion.
2.7 Remove personal metal items such as
rings, bracelets, necklaces, and watches
when working with a lead-acid battery. A
lead-acid battery can produce a short-
circuit current high enough to weld a ring
or the like to metal, causing a severe burn.
2.8 Use charger for charging LEAD-ACID and
AGM-type rechargeable batteries with
recommended rated capacities of 40-200Ah
(6V&12V). It is not intended to supply
power to a low voltage electrical
system other than in a starter-motor
application. Do not use battery charger
for charging dry-cell batteries that are
commonly used with home appliances.
These batteries may burst and cause
injury to persons and damage to property.
2.9 NEVER charge a frozen battery.
3
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 4

4
3. PREPARING TO CHARGE
3.1 7654323110/.5-,5/3+,*35)0--3/.56/,+5
*3('2&35-,52(0/%3$50&#0.15/3+,*35
%/,"4!3!5-3/+'40&56/,+5)0--3/.5 /1-5035
1"/350&&5022311,/'315'45-(35*3('2&350/35,66$5
so as not to cause an arc.
3.2 351"/350/3050/,"4!5)0--3/.5'15#3&&5
ventilated while battery is being charged.
3.3 &3045)0--3/.5-3/+'40&153520/36"&5-,5
keep corrosion from coming in contact
with eyes.
3.4 Add distilled water in each cell until
)0--3/.502'!5/302(315&3*3&5132' 3!5).5
)0--3/.5+04"602-"/3/5,54,-5,*3/ &&5,/505
)0--3/.5#'-(,"-5/3+,*0)&3523&&5201$51"2(
5
015*0&*35/3%"&0-3!5&30!502'!5)0--3/'31$5
carefully follow manufacturer’s recharging
instructions.
3.5 -"!.50&&5)0--3/.5+04"602-"/3/15
132' 25/320"-',415#('&352(0/%'4%504!5
recommended rates of charge.
3.6 Determine voltage of battery by referring
to vehicle owner’s manual and make sure
that output voltage selector switch is set at
2,//32-5*,&-0%357652(0/%3/5(0150!"1-0)&3
5
2(0/%35/0-3$52(0/%35)0--3/.5'4'-'0&&.50-5
lowest rate.
4. CHARGER LOCATION
4.1 ,20-352(0/%3/501560/50#0.56/,+5)0--3/.5
as DC cables permit.
4.2 3*3/5&02352(0/%3/5!'/32-&.50),*35
battery being charged; gases from battery
will corrode and damage charger.
4.3 3*3/50&&,#5)0--3/.502'!5-,5!/'5,45
2(0/%3/5#(345/30!'4%53&32-/,&.-35132' 25
%/0*'-.5,/5 &&'4%5)0--3/.
4.4 Do not operate charger in a closed-in
area or restrict ventilation in any way.
4.5 Do not set a battery on top of charger.
5. DC CONNECTION PRECAUTIONS
5.1 Connect and disconnect DC output clips
only after setting any charger switches to
“off” position and removing AC cord from
3&32-/'25,"-&3-53*3/50&&,#52&'15-,5-,"2(5
each other.
5.2 --02(52&'15-,5)0--3/.504!52(011'1$5015
'4!'20-3!5'45-(35132-',415504!5
6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE
A SPARK NEAR THE BATTERY MAY
CAUSE A BATTERY EXPLOSION. TO
REDUCE THE RISK OF A SPARK NEAR
THE BATTERY:
6.1 Position AC and DC cords to reduce risk
,65!0+0%35).5(,,!$5!,,/$5,/5+,*'4%5
engine part.
6.2 -0.52&30/5,656045)&0!31$5)3&-1$5"&&3.1$504!5
other parts that can cause injury to persons.
6.3 (325,&0/'-.5,65)0--3/.5,1-15775
$5$55)0--3/.5,1-5"1"0&&.5(015&0/%3/5
!'0+3-3/5-(04575$5$5,1-
6.4 Determine which post of battery is
%/,"4!3!52,4432-3!5-,5-(352(011'15765
negative post is grounded to chassis (as
'45+,1-5*3('2&31$513355765,1'-'*35
,1-5'15%/,"4!3!5-,5-(352(011'1$51335
6.5 ,/543%0-'*3%/,"4!3!5*3('2&3$52,4432-5
77552&'56/,+5)0--3/.52(0/%3/5
-,5775$5$55"4%/,"4!3!5,1-5
,65)0--3/.5,4432-5755
clip to vehicle chassis or engine block
away from battery. Do not connect clip to
20/)"/3-,/$56"3&5&'431$5,/51(33-+3-0&5),!.
5
parts. Connect to a heavy gage metal part
of the frame or engine block.
6.6 ,/5,1'-'*3%/,"4!3!5*3('2&3$52,4432-5
7552&'56/,+5)0--3/.5
2(0/%3/5-,575$5$55
ungrounded post of battery. Connect
77552&'5-,5*3('2&352(011'15
or engine block away from battery. Do
4,-52,4432-52&'5-,520/)"/3-,/$56"3&5&'431$5
or sheet-metal body parts. Connect to
a heavy gage metal part of the frame or
engine block.
6.7 (345!'12,4432-'4%52(0/%3/$5-"/45
1#'-2(315-,5,66$5!'12,4432-552,/!$5
/3+,*352&'56/,+5*3('2&352(011'1$504!5
then remove clip from battery terminal.
6.8 33 Operating Instructions for length of
charge information.
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 5

5
7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE
A SPARK NEAR THE BATTERY MAY
CAUSE A BATTERY EXPLOSION. TO
REDUCE THE RISK OF A SPARK NEAR
THE BATTERY:
7.1 Check polarity of battery posts. POSITIVE
(POS, P, +) battery post usually has a larger
diameter than NEGATIVE (NEG, N, –) post.
7.2 Attach at least a 24-inch-long 6-gauge
(AWG) insulated battery cable to
NEGATIVE (NEG, N, –) battery post.
7.3 Connect POSITIVE (RED) charger clip to
POSITIVE (POS, P, +) post of battery.
7.4 Position yourself and free end of cable as
far away from battery as possible – then
connect NEGATIVE (BLACK) charger clip
to free end of cable.
7.5
connection.
7.6 When disconnecting charger, always do
so in reverse sequence of connecting
while as far away from battery as
practical.
7.7 A marine (boat) battery must be removed
and charged on shore. To charge it on
board requires equipment specially
designed for marine use.
8. AC POWER CORD CONNECTIONS
This battery charger is for use on a
nominal 230~240 volt circuit. The plug must
be plugged into an outlet that is properly
installed in accordance with all local codes
and ordinances. The plug pins must fit the
receptacle (outlet).
USING AN EXTENSION CORD
The use of an extension cord is not
recommended. If you must use an
extension cord, follow these guidelines:
Pins on plug of extension cord must be
the same number, size, and shape as
those of plug on charger.
Ensure that the extension cord is
properly wired and in good electrical
condition.
Wire size must be large enough for
the AC ampere rating of charger.
9. ASSEMBLY INSTRUCTIONS
9.1 Remove all cord wraps and uncoil the cables prior to using the battery charger.
10. CONTROL PANEL
LED INDICATORS
POWER (red) LED lit:
CHARGING (yellow) LED lit:
The charger is charging the battery.
CHARGED (green) LED lit:
The battery is fully charged and the
charger is in maintain mode.
NOTE: See the Operating Instructions
section for a complete description of the
charger modes.
DIGITAL DISPLAY
Connecting DC output cord to a battery
what the digital display shows as listed
DANGER-Never alter AC cord or plug provided
-if it does not fit the outlet. An improper
connection can result in a risk of an electric
shock or electrocution.
Connecting the AC cord to 120V power source.
below:
,

Voltage – The digital display shows the
voltage at the charger battery clamps, in
DC volts.
Pushing button to show battery capacity's
percentage,after seconds,go back to voltage/
status automatically.
Battery’s Voltage Digital Display Shows
>15V “HIG” or “V”
“8AO” (“BAD”) or “V”
“CHG”or “V”
charging started
“FUL”or “ V” charging completed
“FUL”or “ V” charging completed
“CHG”or “V” charging started
>3V
3V<V<8V
>8V
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 6

EDOMGNIGRAHCV21&V6
In 6V mode: Start charging with 10A constant
current,
the digital display shows “CHG” and
battery’s voltage alternatively.Once the battery’s
voltage reaches 7.4V, start withconstant voltage
charge at 7.4V,the currentgoes down slowly.
After the current drops to 1Amp, the charging
process is completed.The digital display will
show “FULL” and battery’s voltage alternatively,
and the “Charged” LED indicator will be lit.
11. OPERATING INSTRUCTIONS
WARNING: A spark near battery may cause
a battery explosion.
IMPORTANT: Do not start the vehicle with the
charger connected to the AC outlet, or it could
result in damage to the charger.
NOTE: This charger is equipped with an auto-
start feature. Current will not be supplied to the
battery clamps until battery is properly connected.
The clamps will not spark if touched together.
CHARGING A BATTERY IN THE VEHICLE
1. Turn off all the vehicle’s accessories.
2. Keep the hood open.
3. Clean the battery terminals.
4. Place the charger on a dry, non-flammable
surface.
5. Lay the AC/DC cables away from any fan
blades, belts, pulleys and other moving parts.
6. Connect the battery, following the precautions
listed in sections 6 and 7.
7. Connect the charger to an electrical outlet.
8. Select the battery type and charging rate.
9. When charging is complete, disconnect the
charger from the AC power, remove the
clamps from the vehicle’s chassis, and then
remove the clamp from the battery terminal.
CHARGING A BATTERY OUTSIDE OF
THE VEHICLE
1. Place battery in a well-ventilated area.
2. Clean the battery terminals.
3. Connect the battery, following the
precautions listed in sections 6 and 7.
4. Connect the charger to the electrical outlet.
5. Select the battery voltage, Press , 6V or
12V LED display indicates chosen voltage.
In charging mode Press , Digital display
indicates Volts, % of charging or CHG.
6. When charging is complete (GREEN LED
is lit), disconnect the charger from the AC
power, disconnect the negative clamp,
and finally the positive clamp.
A marine (boat) battery must be removed
and charged on shore.
7.
In 12V mode: Start charging with 10A constant
current, the digital display shows “CHG” and
battery’s voltage alternatively. Once the battery’s
voltage reaches 14.8V,start withconstant voltage
charge at 14.8V,the currentgoes down slowly.
After the current drops to 1Amp, the charging
process is completed.The digital display will
show “FUL” and battery’s voltage alternatively,
and the “Charged” LED indicator will be lit.
CHARGE RATE
The charger will automatically adjust the
charging current, based on battery size,
in order to charge the battery completely,
BATTERY CHARGING TIMES
Times are based on a 50% discharged
battery and may change, depending on age
and condition of battery.
AUTOMATIC CHARGING MODE
When the Automatic Charge is performed,
the charger switches to the maintain
mode automatically after the battery is
charged.
USING THE BATTERY VOLTAGE TESTER
1. With the charger unplugged from the
AC outlet, connect the charger to the
battery following the instructions given
in previous sections.
2. Plug the charger AC power cord into
the AC outlet.
3. Read the voltage on the digital display.
Keep in mind that this reading is only a
battery voltage reading; a false surface
charge may mislead you. Compare the
reading to the chart below.
6 V Battery
Voltage
Reading
12 V Battery
Voltage
Reading
Battery
Condition
6.4 or more 12.8 or more Charged
6.1 to 6.3 12.2 to 12.7 Needs
charging
Less than 6.1 Less than 12.2 Discharged
V
6
6
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 7

12. MAINTENANCE AND CARE
A minimal amount of care can keep your
battery charger working properly for years.
Clean the clamps each time you are
that may have come in contact with the
clamps to prevent corrosion.
Occasionally cleaning the case of the
shiny and help prevent corrosion.
Coil the input and output cords neatly when
storing the charger. This will help prevent
accidental damage to the cords and charger.
Store the charger unplugged from the AC
power outlet, in an upright position.
Store inside, in a cool, dry place. Do not
store the clamps clipped together, clipped to
the handle, on or around metal, or clipped
to the cables.
12. MAINTENANCE AND CARE
13. TROUBLESHOOTING/ERROR CODES
Error Codes
ERROR
CODE DESCRIPTION REASON/SOLUTION
8A0
The battery voltage is less
than 3V.
The battery could be bad. Have it checked or
replaced.
HIG The battery voltage is more
.V51naht
rodekcehctievah;yrettabV42aebdluoctI
replaced.
If you get an error code, check the connections and settings and/or replace the battery.
Troubleshooting
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
Battery clamps do not spark
when touched together.
The charger is equipped
with an auto-start feature.
It will not supply current to
the battery clamps until a
battery is properly connected
The clamps will not spark if
No problem; this is a normal
condition.
The charger will not turn on
when properly connected.
AC outlet is dead.
Poor electrical connection.
Battery is defective.
Check for open fuse or circuit
breaker supplying AC outlet.
Check power cord and
plug.
Have the battery checked.
Connecting the AC input cord
.
. ecruosrewop230-240vaot
The clamps may not well
connect with the battery.
Check clamps connection with
The digital display has no shows.
the battery.
and selected 6V or 12V.
touched together.
13. TROUBLESHOOTING/ERROR CODES
Error Codes
ERROR
CODE DESCRIPTION REASON/SOLUTION
8A0
The battery voltage is less
than 3V.
The battery could be bad. Have it checked or
replaced.
HIG The battery voltage is more
.V51naht
rodekcehctievah;yrettabV42aebdluoctI
replaced.
If you get an error code, check the connections and settings and/or replace the battery.
Troubleshooting
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
Battery clamps do not spark
when touched together.
The charger is equipped
with an auto-start feature.
It will not supply current to
the battery clamps until a
battery is properly connected
The clamps will not spark if
No problem; this is a normal
condition.
The charger will not turn on
when properly connected.
AC outlet is dead.
Poor electrical connection.
Battery is defective.
Check for open fuse or circuit
breaker supplying AC outlet.
Check power cord and
plug.
Have the battery checked.
Connecting the AC input cord
.
. ecruosrewop230-240vaot
The clamps may not well
connect with the battery.
Check clamps connection with
The digital display has no shows.
the battery.
and selected 6V or 12V.
touched together.
7
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 8

Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The box and
recyclable materials in this packaging can be reused or recycled. Any plastic packaging must be
disposed of in accordance with current local authority procedures.
GB
The WEEE symbol on this product means that the battery charger should be ethically
dismantled or recycled to minimise environmental impact. Please check with your local authority
for more information.
FOR INDOOR USE ONLY
IMPORTANT:
ADDITIONAL SAFETY INFORMATION
This Battery Charger is NOT intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are
supervised or have been given instruction concerning use of the Battery Charger by a person
responsible for their safety.
M17 1RY
WARRANTY: The 12 month warranty on this product will need to be activated within
30 days of purchase, please go to our web site and click on the “Warranty” link and
enter your details on the warranty screen. www.streetwizeaccessories.com.
Streetwize Accessories:
Unit 1, Royce Trading Estate, Ashburton Road West,
Trafford Park, Manchester M17 1RY
Sales enquiries: [email protected]
Technical enquiries: [email protected]
www.streetwizeaccessories.com
SWIBC4 Manual AW 2018.qxp_Layout 1 30/07/2018 11:06 Page 1