Streetwize SWBCG8 User manual

6/12Volt 8Amp & 12Amp
Battery Charger
6. To disconnect the battery when charged, switch off the mains supply and
unplug. Caution: Because of risk of explosive gas, only disconnect the
crocodile clips when the mains are disconnected. Check the fluid levels and
top up if necessary (wear protective gloves as this liquid is corrosive) and
wipe the battery clean. If the battery has been removed, replace in the
vehicle and re-connect.
Product Specifications:
Streetwize Part Number: SWBCG8
Voltage Rating Input: 230V 50Hz
Output Rating: 6v DC - 5.6A (High Charge) – 2.5A (Low Charge)
12v DC - 5.6A (High Charge) – 3.6A (Low Charge)
Maximum Charge Rate: 5.6 ADC equal to 8 Amp RMS
Streetwize Part Number: SWBCG12
Voltage Rating Input: 230V 50Hz
Output Rating: 6v DC - 8.4A (High Charge) – 5.2A (Low Charge)
12v DC - 8.4A (High Charge) – 6A (Low Charge)
Maximum Charge Rate: 8.4 ADC equal to 12 Amp RMS
The WEEE symbol on this product means that this product should be
ethically dismantled or recycled to minimise environmental impact.
Please check with your local authority for more information.
IMPORTANT: ADDITIONAL SAFETY INFORMATION
This Battery Charger is NOT intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they are supervised or have been given instruction
concerning use of the Battery Charger by a person responsible for their safety.
FOR INDOOR USE ONLY
SWBCG12
SWBCG8
Please read these instructions carefully before operating this battery charger.
Part No. Rated Output Battery Voltage Battery Capacity
SWBCG8 8 Amp 6/12 Volt 9-112 Ah
SWBCG12 12 Amp 6/12 Volt 9-160 Ah
RoHS
COMPLIANT
M17 1RY
Streetwize Accessories:
Sales enquiries: [email protected]
Technical enquiries: [email protected]
www.streetwizeaccessories.com
WARRANTY: To validate the warranty on this product, please go to our web site and
enter your details on the warranty screen. www.streetwizeaccessories.com.
SWBCG8 & BCG12 Manual AW. 2016.qxp_Layout 1 01/07/2016 09:13 Page 1

Battery Maintenance:
Please check your battery regularly throughout the year and especially in
the winter.
Faulty cells can cause problems with your battery, check the cells with a
hydrometer, if any cell is reading lower than the others it can indicate a faulty
cell. if this is the case have your battery checked, as you may need a new
battery. It is possible that a battery may appear flat when it could simply be a
loose connection of the battery terminals. Check the terminals and tighten if
necessary then check the battery again.
To enable safe operation of this battery charger, make sure you follow basic
safety principles to reduce a risk of personal injury, electric shock and fire.
Always ensure the battery charger is kept in a dry place to avoid damage, and
store out of the reach of children. Do not use the charger in damp or wet areas
as moisture will damage the transformer.
Always check the battery chargers plug, cables and crocodile clips before use.
Do not open the charger, there are no serviceable parts.
When charging, the liquid in the battery may bubble causing a release of gas,
this is flammable so always operate the charger in a well ventilated place and
away from naked flames and sparks.
Do not leave the battery charger whilst in operation for long periods of time.
These chargers are only suitable for 6/12 Volt Lead-Acid batteries and
should not be used to recharge NICAD or any other type of battery.
DANGER: Avoid getting battery acid (electrolyte) on your skin or clothing,
as it may cause burns. If this occurs rinse immediately with cold water
and if necessary seek medical advice.
Please Note: There may be no indication of the Amp Meter needle if the
charger is connected to a fully charged battery.
The charger contains a temperature-sensitive switch that automatically
cuts off when the charger is overloaded or becomes excessively hot. The
charger will switch back on after the unit has cooled.
Safety Instructions:
FOR INDOOR USE ONLY.
Operating Instructions:
Please read the information on the front of these instructions for the maximum
battery capacity recommended for use with this charger. Using with batteries
smaller than this capacity may lead to damage to your battery.
1. Disconnect the Battery from the vehicle to avoid damage to the alternator. It is
advisable were possible to remove the battery from the vehicle as spillage
from the battery can cause damage.
2. If you have a maintenance free/sealed battery it is not necessary to carry
out the following checks. Carefully remove all the caps from each battery cell,
and ensure the liquid as at the recommended level. Top up with distilled or
de-ionised water if required (wear protective gloves as this liquid is corrosive).
Tap water should NOT be used under any circumstances, allow time for any
gases to escape before replacing the caps. Warning: if your battery is the
AUTOFIL type, manufactured by Dagenite or Exide, the glass balls and the
long filler cap MUST be left in place during charging.
3. DO NOT plug the charger in until you have made the following selections. Use
the switch to select 6 volt or 12 volt to match the voltage of the battery being
charged. If you are charging a small battery or you only need a small charge
(to top-up a battery) please select LOW charge. If you are charging a large
battery or you are doing a full charge (flat battery) please select HIGH charge.
4. Connect the crocodile clips in the following order.
a) Connect the positive (+Red) charging lead to the positive (+Red) terminal.
b) Connect the negative (-Black) charging lead to the negative (-Black)
terminal. It is important that the crocodile clips are making good contact with
the battery terminals.
IMPORTANT OPERATING INFO:
5. Plug the Charger in using a fused AC mains plug socket.
When a battery is first connected, the Amp Meter will indicate
that it is charging (needle points to the right, Fig 1), as the
battery becomes charged the charging rate will drop/discharge.
When the charging level is constant (needle points to the left, Fig 2),
the battery is fully charged to it’s optimum level.
Please note: The Amp Meter will never drop to zero during
charging. The Battery Charger has Reverse Polarity Protection
if the leads are incorrectly connected the Amp Meter the
needle will swing back and forth continuously, IMMEDIATELY
unplug the charger from the mains and reverse the connection. Fig 2
Fig 1
SWBCG8 & BCG12 Manual AW. 2016.qxp_Layout 1 01/07/2016 09:13 Page 3