Streetwize Master Charger SW100JS User manual

Product Specifications:
Streetwize Part Number: SW100JS
Voltage Rating Input: 240V 50Hz, 270W
Output Rating: 12v DC - Trickle charge - 7 Amp
Quick charge - 15Amp
Engine Jump Start 100Amp
The WEEE symbol on this product means that this product should be ethically
dismantled or recycled to minimise environmental impact.
Please check with your local authority for more information.
IIMPORTANT: ADDITIONAL SAFETY INFORMATION
This Battery Charger is NOT intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they are supervised or have been given instruction concerning use of the Battery
Charger by a person responsible for their safety.
FOR INDOOR USE ONLY
Please read these instructions carefully before operating this battery charger.
Fully Automatic 7/15Amp 12Volt
Battery Charger
with 100amp Engine Jump Start
for 12v Batteries
Part No. Rated Output Battery Voltage Battery Capacity
SW100JS Trickle - 7Amp 12 Volt 20-150 Ah
Quick charge - 15Amp
Engine start - 100Amp
SW100JS
Fault Possible cause Solution
No charging
current
Bad contact of power socket. Repair or change power socket.
“Select Voltage” switch is set
incorrectly.
Select correct voltage position.
Initial voltage is too low. Change battery.
+ and - polarity terminals of
battery are oxidized and/or dirty.
Clean terminals.
Battery has been damaged. Replace battery.
Low charging
current
+ and - polarity terminals of
battery are oxidized and/or dirty.
Clean terminals.
Battery not accepting charge. Replace battery.
Battery is charged fully. Measure specific gravity.
Excessive
transformer
noise
“Select Voltage” switch is set
incorrectly.
Select correct voltage position.
Unstable position. Position charger on a stable surface.
Streetwize Accessories: Sales enquiries: [email protected]
Technical enquiries: [email protected] www.streetwizeaccessories.com
M17 1RY
RoHS
COMPLIANT
WARRANTY: To validate the warranty on this product, please go to our web site and
enter your details on the warranty screen. www.streetwizeaccessories.com.
SW100JS Manual AW 2016_Layout 1 06/06/2016 17:24 Page 1

Battery Maintenance:
Please check your battery regularly throughout the year and especially in the winter.
Faulty cells can cause problems with your battery, check the cells with a hydrometer, if
any cell is reading lower than the others it can indicate a faulty cell. if this is the case
have your battery checked, as you may need a new battery. It is possible that a battery
may appear flat when it could simply be a loose connection of the battery terminals.
Check the terminals and tighten if necessary then check the battery again.
To enable safe operation of this battery charger, make sure you follow basic safety
principles to reduce a risk of personal injury, electric shock and fire.
Always ensure the battery charger is kept in a dry place to avoid damage, and store out
of the reach of children. Do not use the charger in damp or wet areas as moisture will
damage the transformer.
Always check the battery chargers plug, cables and crocodile clips before use. Do not
open the charger, there are no serviceable parts.
When charging, the liquid in the battery may bubble causing a release of gas, this is
flammable so always operate the charger in a well ventilated place and away from
naked flames and sparks.
This charger is ONLY suitable for use with 12 Volt Lead-Acid batteries and
should not be used to recharge NICAD or any other type of battery.
DANGER: Avoid getting battery acid (electrolyte) on your skin or clothing, as it
may cause burns. If this occurs rinse immediately with cold water and if
necessary seek medical advice.
The charger contains a temperature-sensitive switch that automatically cuts off
when the charger is overloaded or becomes excessively hot. The charger will
switch back on after the unit has cooled.
Operating Instructions:
Please read the information on the front of these instructions for the maximum battery
capacity recommended for use with this charger. Using with batteries smaller than this
capacity may lead to damage to your battery.
1. Disconnect the Battery from the vehicle to avoid damage to the alternator. It is
advisable were possible to remove the battery from the vehicle as spillage from the
battery can cause damage.
Safety Instructions:
FOR INDOOR USE ONLY.
2. If you have a maintenance free/sealed battery it is not necessary to carry out the
following checks. Carefully remove all the caps from each battery cell, and ensure
the liquid is at the recommended level. Top up with distilled or de-ionised water if
required (ALWAYS wear protective gloves as this liquid is corrosive). Tap water
should NOT be used under any circumstances, allow time for any gases to escape
before replacing the caps. Warning: if your battery is the AUTOFIL type,
manufactured by Dagenite or Exide, the glass balls and the long filler cap MUST be
left in place during charging.
3. Use the “top” switch to select the correct battery type AGM or Standard Gel. Then
us the “bottom” switch to select the desired charging mode - trickle, quick charge
or engine start. DO NOT plug the charger in until you have connected the crocodile
clips correctly.
4. Connect the crocodile clips in the following order.
a) Connect the positive (+ Red) charging lead to the positive (+ Red) terminal.
b) Connect the negative (- Black) charging lead to the negative (- Black) terminal.
It is important that the crocodile clips make good contact with the battery terminals.
5. To Charge: Plug the Charger in using a fused AC mains plug socket and turn the
“power” switch to charge . When a battery is first connected, the “current meter”
will show the approximate charging current. The “charge indicator” LED’s will light to
indicate approximate amount of charge in the battery. When the “FULL” LED
illuminates charging is complete. The Battery Charger has Reverse Polarity &
Overload Protection. If the leads are incorrectly connected the REVERSE LED will
light (RED), IMMEDIATELY unplug the charger from the mains and reverse the
connection. If the OVERLOAD LED lights (RED) IMMEDIATELY unplug the charger, it
cannot charge this battery. When the charger has finished charging the CONDITION
LED will light (Green) to indicate the charging is complete. At this point the
battery can remain connected, the automatic charge control will maintain
the battery in a fully charged condition indefinitely.
6. Engine Starting: Charge the battery for 10-15 minutes according to steps 1-5 as
in the charging operation section above. Turn off the mains power, turn the switch to
100Amp engine start, turn on the mains power and then turn the vehicle over
immediately. When the amp switch is in the “engine start” position the charger is
able to operate for a brief period in an over-current mode of operation. Warning: Do
not crank engine for more than 5 seconds at a time. Wait approximately 4 minutes
between starting attempts. Do not attempt to start more than three times. If
three attempts fail, the vehicle’s battery should be recharged fully.
7. To disconnect the battery when charged, or after starting the engine. Unplug the
mains supply. Caution: Because of risk of explosive gas, only disconnect the
crocodile clips when the mains are disconnected. Check the fluid levels and top up
if necessary and wipe the battery clean. If the battery has been removed, replace in
the vehicle and re-connect.
SW100JS Manual AW 2016_Layout 1 06/06/2016 17:24 Page 3