Stryker Medical Renaissance Series User manual

Renaissance Series
1067 Head/Neck Surgery Bed
MAINTENANCE MANUAL
For Parts or Technical Assistance
1–800–327–0770
IMPORTANT
File in your
maintenance
records

Table of Contents
Introduction
Specifications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning / Caution / Note Definition 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventative Maintenance
Cleaning 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checklist 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Information
Pedal Linkage Adjustment – Dual Side Control Base 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Linkage Adjustment – Dual End Control Base 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly Replacement 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Cover Installation and Removal 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic System Troubleshooting 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Hydraulic Fluid Level 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Excess Air From The Hydraulic System 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Descent Rate Adjustment 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Check Valve Replacement
Replacement Of Valve #1 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Of Valve #2 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Of Valve #3 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjustment 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Lubrication Points 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly Drawings And Parts Lists
Side Control Base Assembly 14–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Base Assembly, Pump 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Base Assembly, Head End, Left and Right 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Base Assembly 19–21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Brake Pedal Assembly, Foot and Head 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Pump Pedal Assembly, Head and Foot 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjuster Assembly 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Cam Assembly 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Assembly 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Base Assembly 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly with Steerlock 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fifth Wheel Assembly 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Stretcher Base Labeling Assembly 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Control Stretcher Graphics 30.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side Control Stretcher Graphics 30.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side Control Stretcher Base Labeling Assembly 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Litter Assembly, Manual Fowler, Stationary Foot End 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Frame Assembly, Stationary Foot End 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Fowler Assembly 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Litter Assembly, Crank Fowler, Crank Knee Gatch 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Frame Assembly, Crank Knee Gatch 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crank Fowler Assembly 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fowler Crankscrew Assembly 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knee Gatch Assembly 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knee Gatch Crankscrew Assembly 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Litter Assembly, Articulating Man. Fowler, Stat. Foot End 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Articulating Manual Fowler Assembly 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Litter Assembly, Articulating Crank Fowler, Crank Gatch 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Articulating Crank Fowler Assembly 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail Assembly, Left & Right 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail and Bumper Assembly, Left 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail and Bumper Assembly, Right 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Folding I.V. Holder Assembly 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foot Board/Chartholder Assembly 49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defibrillator Tray Assembly 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wrist Rest Assembly 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wrist Rest Mounting Tube Assembly 52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inflatable Air System Head Pad 53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Parts 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty
Obtaining Parts and Service 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Warranty Coverage 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Authorization 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freight Damage Claims 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2
Introduction
INTRODUCTION
This manual is designed to assist you with the operation and maintenance of the 1067 Head/Neck Surgery
Bed. Read it thoroughly before using the equipment or beginning any maintenance on it.
SPECIFICATIONS
Maximum Weight Capacity 500 pounds
Overall Bed Length/Width 84”/28.25”
Minimum/Maximum Bed Height 24.5”/37.5”
Fowler Angle 0 to 90 degrees
Knee Gatch Angle 0 to 35 degrees
Trendelenburg/Reverse Trendelenburg –12 degrees to +18 degrees
WARNING / CAUTION / NOTE DEFINITION
The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.
WARNING
The personal safety of the patient or user may be involved. Disregarding this information could result in injury
to the patient or user.
CAUTION
These instructions point out special procedures or precautions that must be followed to avoid damaging the
equipment.
NOTE
This provides special information to make maintenance easier or important instructions clearer.
WARNING
Patients should be discouraged from sitting directly on the ends of the stretcher. Excessive weight will cause
the litter surface to tip up, possibly causing patient injury.

Preventative Maintenance
3
CLEANING
1. Hand wash all surfaces of the bed with warm water and mild detergent. Dry thoroughly.
2. Clean Velcro AFTER EACH USE. Saturate Velcro with disinfectant and allow disinfectant to evaporate.
(Appropriate disinfectant for nylon Velcro should be determined by the hospital.)
NOTE
Quaternary Germicidal Disinfectants, used as directed, and/or Chlorine Bleach products, typically 5.25% So-
dium Hypochlorite in dilutions ranging between 1 part bleach to 100 parts water, and 2 parts bleach to 100
parts water are not considered mild detergents. These products are corrosive in nature and may cause dam-
age to your stretcher if used improperly. If these types of products are used to clean Stryker patient handling
equipment, measures must be taken to insure the stretchers are rinsed with clean water and thoroughly dried
following cleaning. Failure to properly rinse and dry the stretchers will leave a corrosive residue on the surface
of the stretcher, possibly causing premature corrosion of critical components. Failure to follow the above
directions when using these types of cleaners may void this product’s warranty.
BIANNUAL CHECKLIST
All fasteners and knobs secure (reference all assembly prints)
Siderails move and latch properly
All casters lock with brake pedal engaged (page 13)
Steer function working properly
All casters secure and swivel properly
Body restraints working properly
I.V. pole intact and operating properly (page 48)
Oxygen bottle holder intact and operating properly
Fowler operates and latches properly
Knee Gatch operates properly (page 39)
Trendelenberg/Reverse Trendelenberg operating properly
No rips or cracks in mattress cover
Ground chain intact
No leaks at hydraulic connections
Hydraulic jacks holding properly (page 8)
Hydraulic drop rate set properly (page 10)
Hydraulic oil level sufficient (page 9)
Lubricate where required, including the brake adjuster assembly and brake cam (page 13)
Serial No.______________
______________
______________
______________
______________
Completed By:_________________________________ Date:_____________

4
Service Information
PEDAL LINKAGE ADJUSTMENT –DUAL SIDE CONTROL BASE
Required Tools:
3/32 Hex Allen Wrench
7/16 Open End Wrench
1/2 Open End Wrench
(2) Wooden blocks (10 –12 inches in length)
Adjustment Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. To adjust the foot end descent pedal, use a 5/32 hex Allen wrench to loosen the set screw (C) in the stop
collar (D) on the release rod. Hold the pedal parallel to the floor and slide the collar up to the bracket on
the release rod. Tighten the set screw on the stop collar. Be sure the head end and foot end descent
pedals are level with each other. Repeat for the head end pedal, if necessary.
4. Once the pedals are level, be sure the paddle on the end of the release rod for the foot end jack is slightly
touching the actuating stem on the jack base. If it is not, use a 3/32 hex Allen wrench to loosen the set
screw on the paddle hub. Adjust the paddle to JUST touch the stem of the jack. Tighten the set screw
in the paddle hub. Repeat for the head end jack, if necessary.
5. Depress the pedal for the foot end jack. The jack should start to descend about the same time the paddle
on the end of the rod contacts the sleeve on the jack actuating stem. The bracket on the foot pedal body
should hit the stop screw (B). Any further movement could cause damage to the stem components inside
the jack housing. To adjust the stop screw, use a 1/2 open end wrench to loosen the hex jam nut (A).
Turn the screw and re–tighten the hex jam nut. Repeat for the head end jack.
6. Pump the litter up to full height.
7. Step on both descent pedals at the same time. Both ends of the litter should lower with the foot end lower-
ing slightly faster than the head end. If it does not, refer to the procedure for adjusting the jack descent
rate.
8. Remove the wooden blocks supporting the base hood. Use the pedal cut–outs on the side of the hood
as a guide for proper re–positioning.

5
Service Information
PEDAL LINKAGE ADJUSTMENT –DUAL END CONTROL BASE
Required Tools:
7/16 Open End Wrench
1/2 Open End Wrench
(2) Wooden Blocks (10 –12 inches in length)
Adjustment Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. The descent pedals should be level with each other and there should be approximately 4 inches between
the floor and the bottom of the pedal. To raise the pedal height, use a 1/2 open end wrench to loosen the
hex jam nut (E). Using your hand, turn the screw (D) into the bracket. To lower the pedal height, loosen
the screw. Tighten the hex jam nut (E) after the correct height is achieved.
4. Once the pedals are level, the release rod can be adjusted. Using a 7/16 wrench, turn nut (B) clockwise
to shorten the release length and counterclockwise to increase the length.
5. Depress the pedal and be sure the jack descent is triggered when the pedal is approximately one inch from
the floor. The descent should stop when the pedal is released and the jack height should hold. Repeat
the above procedures for the descent pedal at the other end of the bed.
6. After adjusting each descent pedal individually, depress both pedals at the same time. Both jacks should
start descending when the pedals are approximately one inch from the floor. The foot end should lower
slightly faster than the head end. If it does not, see procedure for adjusting the jack descent rate.
7. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.

6
Service Information
CASTER ASSEMBLY REPLACEMENT*
Required Tools:
1/8 Roll Pin Punch Drill with 1/8 inch Drill Bit
Flat Punch (any size larger than 1/8) Hammer
Needle Nose Pliers Floor Jack
3/4 Inch Wrench (2) Wooden Blocks (10 –12 inches in length)
1 Inch Wrench Torque Wrench (w/ Ft. Lbs. Adjust.)
Replacement Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. Using a 1/8 roll pin punch and hammer, remove roll pin located in center of lug nut holding wheel assembly
to base frame.
4. Carefully remove plastic wheel covers.
5. Using a floor jack, lift base frame approximately 4 inches off the ground.
6. While holding cap screw with a 3/4 inch wrench, turn lug nut with a 1 inch wrench to loosen wheel assembly
from base frame. Remove wheel.
7. Install the new wheel assembly with new lug nut and tighten down to 60 –65 foot–pounds torque.
WARNING
Never reuse the old lug nut, cap screw or roll pin once removed from base frame.
8. Lower the floor jack and set aside to be used, if needed, with another wheel.
9. Drill a 1/8 hole in center of lug nut, going completely through the lug nut.
CAUTION
Be careful not to ”oblong”the hole in the lug nut when drilling.
10. Using needle nose pliers, hold on to roll pin and tap into place. Finish driving roll pin with a flat head punch
and a hammer until flush with the lug nut.
11. Install plastic wheel covers onto wheel.
12. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.
1/8 Inch
Through Lug Nut
(60–65 Ft.–Lb.)
Support Tube
1 Inch
Dia.
Roll Pin
*Replacement Part Number 715–100–127 (Caster and Cover Assembly)

7
Service Information
CASTER COVER INSTALLATION AND REMOVAL
Double Prongs
Single Prong
align cover with axle nut or bolt head, as shown.
Push down on the opposite side of the cover until
single prong engages with caster horn.
Push with palm on cover until
ProperlyAttached
Cover
To remove wheel cover, insert large screwdriver into cut–out in
side of wheel cover and into the space between the double prongs.
Pry up cover to disengage double prongs and push sharply upward
double prongs engage.
1.
2.
3.
Looking through the larger of the two side cut–outs,
Top View (Cut–Away)
Top View (Cut–Away)
Top View (Cut–Away)
to disengage single prong.

8
Service Information
HYDRAULIC SYSTEM TROUBLESHOOTING
NOTE
Be sure the pedal linkage has been adjusted properly before beginning service on the jacks (see page 4
or page 5).
PROBLEM/SYMPTOM SOLUTION
Jack will not raise to full height. Add hydraulic fluid (see p.9). Check for leaks.
Jack will not hold in raised position. Close the needle valve completely. If the jack holds,
replace valve #1 (see p. 11). If the jack does not
hold, replace valve #2 (see p. 12).
Jack will not pump up and the jack actuator rod
does not move. Close the needle valve. If the jack will now pump
up, replace valve #1. If the jack still will not pump
up after closing the needle valve, replace valve #3
(see p. 12).
Jack will not pump up but the jack actuator rod
does move when the pump pedal is activated. Replace valve #2 (see p. 12).
Jack will not pump up and the jack actuator rod
may or may not move. Remove excess air (vacuum) in system (see p. 9).
Contact Stryker technical service at 1–800–327–0770 for further assistance.

9
Service Information
CHECKING HYDRAULIC FLUID LEVEL
Required Tools:
3/8 Open End Wrench
3/4 Open End Wrench
Procedure:
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the jacks.
1. Using a 3/8 open end wrench, remove square head set screws from both head and foot end jack support
tubes. Remove litter top and set aside.
2. Lift base hood off base frame and set aside.
3. Be sure there are no hydraulic leaks. If there are, jack replacement will be necessary.
4. Lower the jack to the full down position.
5. Using a 3/4 open end wrench, slowly turn the fill plug located on the side of the reservoir counterclockwise
to allow excess system pressure to vent. Remove the fill plug.
6. The hydraulic fluid should be visible at the bottom of the fill hole. If it is not, add Mobil Aero HFA hydraulic
fluid (Stryker part number 2020–70–475) until the fluid is visible at the bottom of the fill hole. Replace the
fill plug.
CAUTION
Use of other types of oil may damage hydraulic units.
7. Replace the hood and the litter.
REMOVAL OF EXCESS AIR (VACUUM) FROM THE HYDRAULIC SYSTEM
Procedure:
1. Verify all hydraulic linkages are secure and operating properly (see pedal linkage adjustment procedure
page 4 or 5).
2. Using pump pedal, actuate system several times. This will force the air through the system and the jack
should now pump up.

10
Service Information
JACK DESCENT RATE ADJUSTMENT
Required Tools:
Screwdriver
(2) Wooden Blocks (10 –12 inches in length)
Adjustment Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. The descent rate needle valve is located on the base of the jack. Turning the needle valve clockwise, with
a screwdriver, will decrease the rate of descent. Turning it counterclockwise will increase the rate of de-
scent.
4. Adjust the needle valve so that the foot end of the stretcher descends slightly faster than the head end.
NOTE
The larger percentage of a patient’s weight is located in the torso area. Adjust descent rate accordingly.
5. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.
NOTE
The jack descent rate was preset at the factory to drop the foot end faster than the head. It is recommended
that the foot drop faster to avoid patient disorientation.

11
Service Information
HYDRAULIC CHECK VALVE REPLACEMENT
Required Tools:
3/8 Open End Wrench Stiff Wire (with bent, pointed end) Small Needle Nose Pliers
3/4 Open End Wrench Torque Wrench (with Ft. Lbs. adjust.)
7/32 Hex Allen Wrench 1/2 Inch Diameter Rod
Replacement of Valve #1
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the stretcher.
1. Using a 3/8 open end wrench, remove square head set screws from both head and foot end jack support
tubes. Remove litter top and set aside.
2. Lift base hood off base frame and set aside.
3. Lower the jack to full down position. The actuator must be manually lowered while depressing the appropri-
ate release pedal.
4. Remove the pin body assembly (4) with a 3/4 open end wrench and discard the housing gasket (5).
NOTE
Although the hydraulic fluid is not under pressure, some fluid loss will occur. The fluid loss should be minimal
but covering the floor is advisable.
5. Using a 7/32 hex Allen wrench, remove the valve plug (6).
6. Using a stiff wire with a bent, pointed end, remove and discard the valve (1) and the seal (7).
7. Install the new seal (7) flat to the bottom of its hole with a 1/2 inch diameter rod and install the new valve
(1) with the beveled end out (as shown in the illustration).
8. Install the valve plug (6) with the countersunk end first and the beveled end out. Tighten to 10 foot pounds
torque.
9. Install the pin body assembly (4) with the new housing gasket (5) and tighten to 10 foot pounds torque.
10. Pump up the jack to the maximum height. Apply weight to be sure the jack holds its position and there
are no hydraulic leaks before replacing the base hood and the litter.
ITEM PART NO. PART NAME
1 926–20–153 Check Valve
2 926–20–153 Check Valve
3 715–1–341 Poppet
4 715–100–312 Pin Housing Assembly*
715–270–100 Valve Assembly**
5 715–1–330 Housing Gasket
6 715–1–309 Valve Plug
7 926–20–154 Seal
8 715–1–101 Base Plug
9 926–20–156 Seal
10 715–1–309 Valve Plug
11 926–20–154 Seal
12 715–1–301 Base Plug
13 926–20–156 Seal
14 390–2–134 Conical Comp. Spring
* Used on jack part number 715–100–310.
** Used on jack part number 715–270–10.
(see label on side of jack reservoir for jack part number)
FILLER PLUG
3
14
12
13

12
Service Information
HYDRAULIC CHECK VALVE REPLACEMENT (CONT’D)
Replacement of Valve #2
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the jacks. Lower the jack rod completely to relieve the pressure on the pump piston side of the
jack. This will prevent large hydraulic fluid loss and possible damage when the base plugs are removed.
1. Remove the base plug (8) and discard the seal (9).
2. Remove the valve plug (10).
3. Using a stiff wire with a bent, pointed end, remove the valve (2) and the seal (11) and discard the seal.
4. Install the new seal (11) flat to the bottom of its hole with a 1/2”diameter rod.
5. Install the new valve (2) with the beveled end out (as shown in the illustration).
6. Install the valve plug (10) and tighten to 10 foot–pounds torque.
7. Install the new seal (9) with the base plug (8) and tighten to 10 foot–pounds torque.
8. Pump up the jack to the maximum height.
9. Be sure there are no hydraulic leaks before replacing the base hood and the litter.
Replacement of Valve (Poppet) #3
WARNING
To avoid personal injury or damage to the stretcher, remove the litter and the base hood before beginning
service on the jacks. Lower the jack rod completely to relieve the pressure on the pump piston side of the
jack. This will prevent large hydraulic fluid loss and possible damage when the base plugs are removed.
1. Remove the base plug (12) and discard the seal (13).
2. Remove the compression spring (14).
3. Using a small needle nose pliers, remove the poppet (3).
4. Install the new poppet (3).
5. Install the compression spring (14).
6. Install the new seal (13) and the base plug (12) and tighten to 10 foot–pounds torque.
7. Pump up the jack to the maximum height to check its operation.
8. Check for hydraulic leaks before replacing the base hood and the litter.

13
Service Information
BRAKE ADJUSTMENT
Required Tools:
3/32”Hex Allen Wrench
Pry Bar
Thread ”Locktite”
BASE LUBRICATION
1. Lubricate brake adjuster rod
around area shown with MPG–2
grease or equivalent.
Do not grease area shown.

1067–1–10 Side Control Base Assembly
14
FOOT END DETAIL A
HEAD END
See Detail A

1067–1–10 Side Control Base Assembly
15
Item Part No. Part Name Qty.
A 1210–1–104 Pump Pedal Link Ass’y1
B (Page 27.1) Jack Assembly 2
C11–262 Flat Washer 12
D3–62 Hex Hd. Cap Screw 8
E11–3 Flat Washer 12
F16–36 Nylock Hex Nut 16
H 715–1–192 Jack Support 2
J3–85 Hex Hd. Cap Screw 8
K52–284 Spacer 3
L 715–1–193 Jack Support Clamp 2
M13–38 Ext. Tooth Lock Washer 4
N 1210–1–115 Pedal Pivot, Right 1
P 1210–1–114 Pedal Pivot, Left 1
R 763–1–16 Spring Holder 1
S38–246 Jack Spring 1
T 715–1–133 Collar 1
W 1210–1–127 Pump Connect. Rod Ass’y1
Y4–146 Hex Socket Hd. Cap Screw 2
Z16–48 Nylock Hex Nut 2
AA 715–1–333 Release Rod Stop Sleeve 2
AB 715–1–346 Release Paddle 1
AC 21–119 Set Screw 1
AD 5050–1–222 Head End Linkage 1
AE 11–4 Washer 1
AF 52–245 Nyliner 3
AH 3–47 Hex Hd. Cap Screw 4
AJ 16–28 Hex Nut 4
AK 52–747 Bearing 4
AL 27–4 Cotter Pin 2
AM (page 18) Side Release Pedal Ass’y2
AN 1210–1–139 Release Rod Weldment 1
AP 1210–1–134 Rel. Pedal Linkage Wldmt. 1
AR 1210–1–138 Release Rod Clamp 1
AS 16–3 Fiberlock Nut 1
AT 16–49 Flexlock Nut 1
AW (Page 17) Pedal Base Assembly 1
AY 715–1–92 Pump Pedal Shaft 1
AZ 715–1–134 Bellows 2
BA 1068–1–110 Hood Assembly 1
BB 21–22 Set Screw 2
BC 27–7 Cotter Pin 2
Item Part No. Part Name Qty.
BD 715–1–140 Raufilam Braid Tubing 1
CA 1210–1–120 Base Weldment 1
CB 715–2–20 Caster Assembly 4
CC 715–1–158 Caster Nut 4
CD 715–1–61 Caster Brake Assembly 2
CE (Page 24) Brake Adjuster Assembly 2
CF 1068–1–45 Brake/Steer Rod 1
CH 16–2 Fiberlock Nut 2
CJ (Page 25) Brake Cam Assembly 2
CK 715–201–201 Brake/Steer Pedal 1
CL 715–1–94 Compression Spring 2
CM 921–1–282 Serial No. Label 1
CN 26–261 Groove Pin 1
CP 715–1–11 Brake Cushion 4
CR 946–1–116 Brake Bar Bushing 4
CS 26–13 Roll Pin 2
CT 23–25 Self–Tapping Screw 2
CU 715–1–165 Actuator Plate Assembly 2
CV 715–1–156 Grounding Chain 1
CW 14–2 Nylon Washer 7
CX 42–20 Collar w/ Set Screw 2
CY 8–17 Soc. Hd. Cap Screw 2
CZ (page 22) Brake Pedal 1
DA 4–160 Soc. Hd. Cap Screw 1
DB 715–1–266 Caster Cover, Left 4
DC 715–1–265 Caster Cover, Right 4
DD 8–21 Soc. Hd. Cap Screw 1
DE 26–8 Roll Pin 1
DF 715–1–161 Fifth Wheel Cam 1
DH 715–1–337 Fifth Wheel Plate Assembly 1
DJ 715–1–157 Fifth Wheel Bearing 1
DK 715–1–136 Fifth Wheel Spring 1
DL 16–16 Fiberlock Nut 1
DM 715–1–217 Fifth Wheel Latch 1
DN 3–20 Hex Hd. Cap Screw 1
DP 81–219 Fifth Wheel Bearing 1
DR (Page 29) Fifth Wheel Assembly 1
DS 715–1–149 Woodruff Key 1
DT 38–211 Spring 1
DW 1000–10–62 Steer Lock Linkage Bar 1
DX (Page 28) Steering Caster Assembly 1
P/N 715–259–400 –Kit to replace 4 standard caster assemblies with necessary hardware –no caster covers.
P/N 715–269–400 –Kit to replace 3 standard caster assemblies and 1 steerlock caster with necessary hard-
ware –no caster covers.
P/N 715–259–100 –Kit to replace 1 standard caster assembly with necessary hardware –no caster covers.
P/N 1010–56–200 –Kit to replace both caster covers on all four wheels.

1067–1–10 Side Control Base Assembly
16
FOOT END
HEAD END

17
715–1–108 Pedal Base Assembly, Pump
Item Part No. Part Name Qty.
A 715–1–83 Pedal Ass’y Weldm’t, Pump 1
B 715–1–126 Side Control Pedal Pad 2
C81–44 Bearing, Bronze 2
NOTE
Apply plastic adhesive to the mating surfaces of item B prior to assembly.

18
715–1–109 Pedal Base Assembly, Left
Item Part No. Part Name Qty.
A 715–1–98 Release Ped. Wldmt., Hd. Lt. 1
B 721–40–25 Pedal 1
715–1–110 Pedal Base Assembly, Head End, Right
Item Part No. Part Name Qty.
A 715–1–97 Release Pedal Weldment 1
B 721–40–25 Pedal 1
NOTE
Apply plastic adhesive to the mating surfaces of item B prior to assembly.

1067–2–10 End Control Base Assembly
19
See Detail A
Detail A