Stryker Medical Renaissance Series User manual

Renaissance Series
720 Transport Stretcher
MAINTENANCE MANUAL
For Parts or Technical Assistance
1–800–327–0770
IMPORTANT
File in your
maintenance
records

Table of Contents
Introduction
Specifications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning / Caution / Note Definition 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventative Maintenance 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Information
Pneumatic Fowler Adjustment 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail Latch Adjustment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Board Counterbalance Adjustment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedal Linkage Adjustment 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly Replacement 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Cover Installation And Removal 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stretcher Height Adjustment 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjustment 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Lubrication 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly Drawings and Parts Lists
End Control Base Assembly (with Wheels) 12, 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjuster Assembly 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Cam Assembly 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Pedal Assembly, Head and Foot End 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly with Steerlock 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster and Caster Cover Replacement Kits 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fifth Wheel Assembly 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stretcher Base Assembly 20, 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Labeling Assembly 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stretcher Graphics 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Litter Assembly 24, 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pneumatic Fowler Assembly 26–26.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Fowler Assembly 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short Transfer System to Frame Assembly 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short Transfer System Assembly, Left 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Short Transfer System Assembly, Right 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Long Transfer System to Frame Assembly 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Long Transfer System Assembly, Left 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Long Transfer System Assembly, Right 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail Assembly, Right & Left 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–Stage I.V. Pole Assembly, Foot & Head 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–Stage I.V. Pole Assembly 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–Stage I.V. Pole Assembly, Head & Foot 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–Stage I.V. Pole Assembly 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2nd Stage Assembly 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3rd Stage Assembly 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tethered I.V. Pole Mounting Assembly 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tethered I.V. Pole Assembly 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tethered I.V. Pole Trough Assembly 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C–Spine Cassette Holder Assembly 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C–Spine Support Pole Assembly 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C–Spine Storage Bracket Assembly 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defibrillator Tray Assembly 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foot Board/Chartholder Assembly 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upright Oxygen Bottle Holder Assembly 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Parts 49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty
Obtaining Parts and Service 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Warranty Coverage 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Authorization 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freight Damage Claims 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2
Introduction
INTRODUCTION
This manual is designed to assist you with the operation and maintenance of the 720 Transport Stretcher.
Read it thoroughly before using the equipment or beginning any maintenance on it.
NOTE
This manual applies only to 720 stretchers built after 1993, with serial numbers after 94010000. For 720
stretchers built before 1994, use manual part number 720–100–25.
SPECIFICATIONS
Maximum Weight Capacity 500 pounds
Overall Bed Length/Width 81”, 30”
Fixed Height Options 28”, 30”,32”
Fowler Angle 0 to 90 degrees
Stryker reserves the right to change specifications without notice.
WARNING / CAUTION / NOTE DEFINITION
The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.
WARNING
The personal safety of the patient or user may be involved. Disregarding this information could result in injury
to the patient or user.
CAUTION
These instructions point out special procedures or precautions that must be followed to avoid damaging the
equipment.
NOTE
This provides special information to make maintenance easier or important instructions clearer.
WARNING
Patients should be discouraged from sitting directly on the ends of the stretcher. Excessive weight will cause
the litter surface to tip up, possibly causing patient injury.
Always apply the caster brakes when a patient is getting on or off the stretcher. Push on the stretcher to en-
sure the brakes are securely locked. Always engage the brakes unless the stretcher is being moved. Injury
could result if the stretcher moves while a patient is getting on or off the stretcher.

3
Preventative Maintenance
CHECKLIST (PERFORM A MINIMUM OF TWICE A YEAR)
All fasteners secure (reference all assembly prints)
Siderails move and latch properly (page 5)
Engage brake pedal and push on the stretcher to ensure all casters lock securely (page 10)
Steer function working properly
All casters secure and swivel properly
Body restraints working properly
I.V. pole intact and operating properly
Oxygen bottle holder intact and operating properly (page 48)
Fowler operates and latches properly (pneumatic: page 4, manual: page 27)
No rips or cracks in mattress cover
Transfer boards intact and operating properly (page 5)
Ground chain intact
Lubricate where required, including the brake adjuster assembly and brake cam (page 10)
Accessories and mounting hardware in good condition and working properly
Serial No.______________
______________
______________
______________
______________
Completed By:_________________________________ Date:_____________

3.1
Cleaning
Hand wash all surfaces of the stretcher with warm water and mild detergent. Dry thoroughly. DO NOT
STEAM CLEAN, PRESSURE WASH, HOSE OFF OR ULTRASONICALLY CLEAN. Using these methods
of cleaning is not recommended and may void this product’s warranty.
Clean Velcro AFTER EACH USE. Saturate Velcro with disinfectant and allow disinfectant to evaporate. (Ap-
propriate disinfectant for nylon Velcro should be determined by the hospital.)
In general, when used in those concentrations recommended by the manufacturer, either phenolic type or
quaternary type disinfectants can be used. Iodophor type disinfectants are not recommended for use. The
following products have been tested and have been found not to have a harmful effect WHEN USED IN AC-
CORDANCE WITH MANUFACTURERS RECOMMENDED DILUTION.*
TRADE NAME DISINFECTANT
TYPE
MANUFACTURER *MANUFACTURER’S RECOMMENDED
DILUTION
A33 Quaternary Airwick (Professional Products Division) 2 ounces/gallon
A33 (dry) Quaternary Airwick (Professional Products Division) 1/2 ounce/gallon
Beaucoup Phenolic Huntington Laboratories 1 ounce/gallon
Blue Chip Quaternary S.C. Johnson 2 ounces/gallon
Elimstaph Quaternary Walter G. Legge 1 ounce/gallon
Franklin
Phenomysan
F2500
Phenolic Purex Corporation 1 1/4 ounce/gallon
Franklin Sentinel Quaternary Purex Corporation 2 ounces/gallon
Galahad Phenolic Puritan Churchill Chemical Company 1 ounce/gallon
Hi–Tor Quaternary Huntington Laboratories 1/2 ounce/gallon
LPH Phenolic Vestal Laboratories 1/2 ounce/gallon
Matar Phenolic Huntington Laboratories 1/2 ounce/gallon
Omega Quaternary Airwick (Professional Products Division) 1/2 ounce/gallon
Quanto Quaternary Huntington Laboratories 1 ounce/gallon
Sanikleen Quaternary West Chemical Products 2 ounces/ gallon
Sanimaster II Quaternary Service Master 1 ounce/gallon
Vesphene Phenolic Vestal Laboratories 1 1/4 ounce/ gallon
Quaternary Germicidal Disinfectants, used as directed, and/or Chlorine Bleach products, typically 5.25% So-
dium Hypochlorite in dilutions ranging between 1 part bleach to 100 parts water, and 2 parts bleach to 100
parts water are not considered mild detergents. These products are corrosive in nature and may cause dam-
age to your stretcher if used improperly. If these types of products are used to clean Stryker patient handling
equipment, measures must be taken to insure the stretchers are rinsed with clean water and thoroughly dried
following cleaning. Failure to properly rinse and dry the stretchers will leave a corrosive residue on the surface
of the stretcher, possibly causing premature corrosion of critical components. Failure to follow the above
directions when using these types of cleaners may void this product’s warranty.
REMOVAL OF IODINE COMPOUNDS
This solution may be used to remove iodine stains from mattress cover and foam footrest pad surfaces.
1. Use a solution of 1–2 tablespoons Sodium Thiosulfate in a pint of warm water to clean the stained area.
Clean as soon as possible after staining occurs. If stains are not immediately removed, allow solution to
soak or stand on the surface.
2. Rinse surfaces which have been exposed to the solution in clear water before returning bed to service.

3.2
Notes

Service Information
4
PNEUMATIC FOWLER ADJUSTMENT
Required Tools:
5/32”Hex Allen Wrench 1/2”Open End Wrench
Adjustment Procedure:
1. For part identification, refer to page 26.2, drawing 721–231–120.
2. For easier access, move Fowler to 75_or higher.
3. Using a 1/2”open end wrench, loosen the nuts (item K) in the actuator arms on the end of the trip bar (F).
4. To adjust the Fowler, use a 5/32”hex Allen wrench to turn the Allen screws (item N) 1 to 2 turns counter–
clockwise if the Fowler will not move or 1 to 2 turns clockwise if the Fowler will not hold its position.
5. Retighten the nuts. Be sure the Fowler will travel from flat to 90_and down again and will hold its position
when weight is applied before returning the stretcher to service.

Service Information
5
SIDERAIL LATCH ADJUSTMENT
Required Tools:
1/8 Hex Allen Wrench
WARNING
The siderail latch adjustment is pre–set at the factory, and should not normally need adjusting. If adjustment
must be done it is important to follow the procedure below. If it is not done properly, injury could occur.
Adjustment Procedure:
1. Using a 1/8”hex Allen wrench, adjust the Allen screw located on the latch assembly opposite the latch.
Turning the screw clockwise will DECREASE the amount of ”play”in the latch. Turning counterclockwise
will INCREASE the amount. The amount of ”play”in the siderail, when in full up engaged position, should
be approximately 1/8 to 3/16 inches.
CAUTION
Too much ”play”when the siderail is in the full up engaged position will give the siderail the appearance of
being unstable and could also cause premature wearing of the latch system. Too little ”play”will obstruct
the latch and keep it from engaging completely in the full up position, which may cause damage to the latch
and/or injury to the patient or user.
TRANSFER BOARD COUNTERBALANCE ADJUSTMENT
Required Tools:
7/16 Open End Wrench
Adjustment Procedure:
1. Raise the transfer board to the full up position.
2. Unhook the extension spring at the eye bolt.
3. Using a 7/16 open end wrench, loosen the jam nut at the eye bolt and adjust the eye bolt to the desired
position.
4. Tighten the jam nut.
5. Hook the extension spring to the eye bolt.
6. Allow the transfer board to lower on its own.
7. Repeat steps 1–7 until the desired counterbalance is achieved.

Service Information
6
PEDAL LINKAGE ADJUSTMENT
Required Tools:
7/16 Open End Wrench
1/2 Open End Wrench
(2) Wooden Blocks (10 –12 inches in length)
Adjustment Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. The descent pedals should be level with each other and there should be approximately 4 inches between
the floor and the bottom of the pedal. To raise the pedal height, use a 1/2 open end wrench to loosen the
hex jam nut (E). Using your hand, turn the screw (D) into the bracket. To lower the pedal height, loosen
the screw. Tighten the hex jam nut (E) after the correct height is achieved.
4. Once the pedals are level, the release rod can be adjusted. Using a 7/16 wrench, turn nut (B) clockwise
to shorten the release length and counterclockwise to increase the length.
5. Depress the pedal and be sure the jack descent is triggered when the pedal is approximately one inch from
the floor. The descent should stop when the pedal is released and the jack height should hold. Repeat
the above procedures for the descent pedal at the other end of the bed.
6. After adjusting each descent pedal individually, depress both pedals at the same time. Both jacks should
start descending when the pedals are approximately one inch from the floor. The foot end should lower
slightly faster than the head end. If it does not, see procedure for adjusting the jack descent rate.
7. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.

Service Information
7
CASTER ASSEMBLY REPLACEMENT
Required Tools:
1/8 Roll Pin Punch Drill with 1/8 inch Drill Bit
Flat Punch (any size larger than 1/8) Hammer
Needle Nose Pliers Floor Jack
3/4 Inch Wrench (2) Wooden Blocks (10 –12 inches in length)
1 Inch Wrench Torque Wrench (w/ Ft. Lbs. Adjust.)
Replacement Procedure:
1. Pump the litter up to full height.
2. Lift the base hood, separating the hood from the base frame. Using the wooden blocks, support the base
hood.
3. Using a 1/8 roll pin punch and hammer, remove roll pin located in center of lug nut holding wheel assembly
to base frame.
4. Carefully remove plastic wheel covers.
5. Using a floor jack, lift base frame approximately 4 inches off the ground.
6. While holding cap screw with a 3/4 inch wrench, turn lug nut with a 1 inch wrench to loosen wheel assembly
from base frame. Remove wheel.
7. Install the new wheel assembly with new lug nut and tighten down to 60 –65 foot–pounds torque.
WARNING
Never reuse the old lug nut, cap screw or roll pin once removed from base frame.
8. Lower the floor jack and set aside to be used, if needed, with another wheel.
9. Drill a 1/8 hole in center of lug nut, going completely through the lug nut.
CAUTION
Be careful not to ”oblong”the hole in the lug nut when drilling.
10. Using needle nose pliers, hold on to roll pin and tap into place. Finish driving roll pin with a flat head punch
and a hammer until flush with the lug nut.
11. Install plastic wheel covers onto wheel.
12. Remove the wooden blocks supporting the base hood and secure the hood to the base frame.
1/8 Inch
Through Lug Nut
(60–65 Ft.–Lb.)
Support Tube
1 Inch
Dia.
Roll Pin
*Replacement Part Number 715–100–127 (Caster and Cover Assembly)

Service Information
7.1
CASTER MAINTENANCE
Required Tools:
5/8”Wrench
11/16”Wrench
Maintenance Procedure:
AB
C
D
Remove the plastic caster cover (see page 8).
Using the 5/8”wrench and the 11/16”wrench, remove the centerlock nut (item A) from the through bolt
(item B) for the caster wheel.
Support the corner of the stretcher where the wheel is being removed and remove the through bolt (item
B) and the molded wheel (item C) .
Clean the through bolt, molded wheel, and the inside of the caster horn (item D) removing any dirt and
debris. Ensure the bearings in the molded wheel spin freely and easily.
Replace the molded wheel and the through bolt.
Replace the centerlock nut on the through bolt and use the 5/8”and 11/16”wrenches to tighten it securely.

Notes
7.2

Service Information
8
CASTER COVER INSTALLATION AND REMOVAL
Double Prongs
Single Prong
align cover with axle nut or bolt head, as shown.
Push down on the opposite side of the cover until
single prong engages with caster horn.
Push with palm on cover until
ProperlyAttached
Cover
To remove wheel cover, insert large screwdriver into cut–out in
side of wheel cover and into the space between the double prongs.
Pry up cover to disengage double prongs and push sharply upward
double prongs engage.
1.
2.
3.
Looking through the larger of the two side cut–outs,
Top View (Cut–Away)
Top View (Cut–Away)
Top View (Cut–Away)
to disengage single prong.

Service Information
9
STRETCHER HEIGHT ADJUSTMENT
NOTE
The 720 Transport Stretcher is available in three ”fixed”heights: 28”, 30”, and 32”. The pre–set stretcher
height was chosen at the time of purchase. Follow the procedure below to change the stretcher height. Refer
to page 20 & 21 for part reference.
Required Tools:
1/2”Open End Wrench
1/2”Socket with Ratchet
Adjustment Procedure:
WARNING
Do not attempt the following adjustment with a patient on the stretcher or injury could occur.
1. Using a 1/2”open end wrench and 1/2”socket with ratchet, loosen the 2 bolts (F) and 2 self–locking nuts
(J) located on the head and foot end upper tower assemblies (B).
2. Remove only the 4 self–locking nuts (J).
3. Lift the litter top from both ends simultaneously only enough to relieve the pressure on the 4 bolts (F) and
remove the bolts and 8 washers (L).
4. Adjust to the desired height by aligning the appropriate holes located in both the head and foot end upper
and lower tower assemblies.
5. Reinstall the 4 bolts, 8 washers and 4 self–locking nuts and tighten securely.

Service Information
10
BRAKE ADJUSTMENT
Required Tools:
3/32”Hex Allen Wrench
Pry Bar
Thread ”Locktite”
BASE LUBRICATION
1. Lubricate brake adjuster rod
around area shown with MPG–2
grease or equivalent.
Do not grease area shown.

Notes
11

End Control Base Assembly (with Wheels and Brakes)
12
Note:
Parts and assemblies drawn with broken
lines are part of optional accessories.
Assembly part number 716–1–251

End Control Base Assembly (with Wheels and Brakes)
13
Item Part No. Part Name Qty.
A 716–1–246 Base Weldment Ass’y1
B8–17 Soc. Hd. Shoulder Bolt 1
C 715–1–158 Caster Nut 4
D 715–1–61 Caster Brake Assembly 2
E (Page 14) Brake Adjuster Assembly 2
F 1210–1–345 Brake/Steer Pedal, Ft. End 1
H 1210–1–346 Brake/Steer Pedal, Hd. End 1
J (Page 15) Brake Cam Assembly 2
K26–8 Roll Pin 1
L 715–1–94 Compression Spring 2
M21–50 Set Screw 2
N 715–1–161 Fifth Wheel Cam 1
P 715–1–11 Brake Cushion 4
R 946–1–116 Brake Bar Bushing 4
T23–25 Self–Tapping Screw 2
Y16–49 Flexlock Nut 1
Z 715–1–337 Fifth Wheel Plate Ass’y1
AA 715–1–231 Brake/Steer Rod Weldment 1
AB 26–261 Clevis Pin 2
AC 715–1–157 Fifth Wheel Bearing 1
AD 715–1–165 Actuator Plate Assembly 1
AF 715–1–136 Fifth Wheel Spring 1
AH 42–20 Collar w/ Set Screw 2
AJ 8–17 Soc. Hd. Shoulder Bolt 1
AK 14–2 Nylon Washer 6
AL 16–16 Nylock Nut 1
AM 715–1–156 Grounding Chain 1
AN 16–2 Fiberlock Nut 2
AP 715–1–217 Fifth Wheel Latch 1
AR 3–20 Hex Hd. Cap Screw 1
AS (Page 17) Steering Caster Ass’y1
AT (Page 18) Caster Wheel Ass’y3
AY 81–219 Bearing 1
AW 26–13 Roll Pin 1
AZ (Page 19) Fifth Wheel Ass’y1
BA 715–1–149 Woodruff Key 1
BB 1000–10–62 Steering Lock Linkage Bar 1
BC 38–211 Spring 1
BD 8–21 Soc. Hd. Shoulder Bolt 1
STEERLOCK
ASSEMBLY
DETAIL

14
715–1–150 Brake Adjuster Assembly
Item Part No. Part Name Qty.
A 715–1–62 Threaded Stud Assembly 1
B14–4 Nylon Washer 4
C 715–1–180 Bearing 2
D28–8 Retaining Ring 2

15
715–1–213 Brake Cam Assembly
Item Part No. Part Name Qty.
A 715–1–221 Brake Cam 1
B16–59 Fiberlock Nut 1
C8–21 Soc. Hd. Cap Screw 1
D 715–1–173 Brake Connecting Link 1