Stryker 1080 User manual

Medical
For parts or technical
assistance call
800 327 0770 (option 2)
Fluoroscopy Stretcher
Model 1080
Maintenance
Manual
Important
Information
File in your
maintenance
records

Table of Contents
Introduction
Specifications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning / Caution / Note Definition 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventative Maintenance
Checklist 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Information
Pneumatic Fowler Adjustment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Folddown Siderail Latch Adjustment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Maintenance 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Cam Replacement 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Ring Replacement 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake/Steer Pedal Replacement 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic System Troubleshooting 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Replacement 10, 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Hydraulic Fluid Level 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priming Pump 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing Excess Air (Vacuum) From the Hydraulic System 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mattress Maintenance 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjustment 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Lubrication Points 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Reference Replacement Parts List 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly Drawings and Parts Lists
Base Assembly 15−19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack & Control Assembly 20−22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Assembly 23−25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjuster Assembly 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Litter Assembly 27−30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pneumatic Fowler Assembly 31, 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail to Litter Assembly 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Siderail Assembly 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessory Rail to Litter Assembly 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foot Board/Chart Holder Assembly 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I.V. Pole Assembly 37−40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foot Board/Chart Holder Assembly 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upright Oxygen Bottle Holder 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limited Warranty
Obtaining Parts and Service 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Warranty Coverage 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Authorization 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freight Damage Claims 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return to Table of Contents

2
Introduction
INTRODUCTION
This manual is designed to assist you with the maintenance of the 1080 Fluoroscopy Stretcher. Read it thor-
oughly before using the stretcher or beginning any maintenance on it.
SPECIFICATIONS
Maximum Weight Capacity 500 pounds
Overall Stretcher Length/Width 87” x 30.5”
Patient Surface Length/Width 84” x 26”
Minimum/Maximum Stretcher Height 24”/34”
Fowler Angle 0 degrees to 90 degrees
Trendelenburg/Reverse Trendelenburg −8 degrees to +8 degrees
Fluoroscopy Window 19.5” x 66”
C−Arm Access Width 54”
Stryker reserves the right to change specifications without notice.
WARNING / CAUTION / NOTE DEFINITION
The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed.
WARNING
Alerts the reader about a situation, which if not avoided, could result in death or serious injury. It may also
describe potential serious adverse reactions and safety hazards.
CAUTION
Alerts the reader of a potentially hazardous situation, which if not avoided, may result in minor or moderate
injury to the user or patient or damage to the equipment or other property. This includes special care neces-
sary for the safe and effective use of the device and the care necessary to avoid damage to a device that
may occur as a result of use or misuse.
NOTE
This provides special information to make maintenance easier or important instructions clearer.
Safe Working Load
Return to Table of Contents

3
Preventative Maintenance
CHECKLIST
All fasteners secure
Siderails move and latch properly −securing pins and screws are intact
Engage brake pedal and push on the stretcher to ensure all casters lock securely (page 13)
All casters secure and swiveling properly
Steer function working properly
Fowler operating properly
Trendelenberg/Reverse Trendelenberg operating properly
No rips or cracks in mattress cover
No leaks at hydraulic connections
Hydraulic jacks holding properly
Hydraulic drop rate set properly
Hydraulic oil level sufficient
I.V. pole intact and operating properly
Oxygen bottle holder intact
Accessories and mounting hardware in good condition and operating properly
Lubricate where required, including the brake adjuster assembly, the brake cam, and the pump bar
pivot brackets (page 13)
Serial No.______________
______________
______________
______________
______________
______________
______________
______________
Completed By:_________________________________ Date:_____________
NOTE
Preventative maintenance should be performed at a minimum of annually. A preventative maintenance pro-
gram should be established for all Stryker Medical equipment. Preventative maintenance may need to be
performed more frequently based on the usage level of the product.
Return to Table of Contents

4
Cleaning
Hand wash all surfaces of the stretcher with warm water and mild detergent. DRY THOROUGHLY. Do not
steam clean, pressure wash, hose off or ultrasonically clean. Using these methods of cleaning is not recom-
mended and may void this product’s warranty.
Suggested cleaners for stretcher surfaces:
Quaternary Cleaners (active ingredient −ammonium chloride)
Phenolic Cleaners (active ingredient −o−phenylphenol)
Chlorinated Bleach Solution (5.25% −less than 1 part bleach to 100 parts water)
Avoid oversaturation and ensure the product does not stay wet longer than the chemical manufacturer’s
guidelines for proper disinfecting.
CAUTION
SOME CLEANING PRODUCTS ARE CORROSIVE IN NATURE AND MAY CAUSE DAMAGE TO THE
PRODUCT IF USED IMPROPERLY. If the products described above are used to clean Stryker patient care
equipment, measures must be taken to insure the beds are wiped with clean water and thoroughly dried fol-
lowing cleaning. Failure to properly rinse and dry the beds will leave a corrosive residue on the surface of
the bed, possibly causing premature corrosion of critical components. Failure to follow the above directions
when using these types of cleaners may void this product’s warranty.
For mattress cleaning instructions, please see the tag on the mattress, or contact the mattress manufacturer.
Clean VelcroAFTER EACH USE. Saturate Velcro with disinfectant and allow disinfectant to evaporate.
(Appropriate disinfectant for nylon Velcroshould be determined by the hospital.
Return to Table of Contents

5
Service Information
PNEUMATIC FOWLER ADJUSTMENT
Required Tools:
5/32” Hex Allen Wrench 1/2” Open End Wrench
Adjustment Procedure:
1. Refer to drawing 1080−31−120 (Pneumatic Fowler Assembly, page 31) for parts reference.
2. For easier access, move Fowler to 75 degrees or higher.
3. Using a 1/2” open end wrench, loosen the nuts (item E) in the actuator arms on the end of the trip bar (N).
4. To adjust the Fowler, use a 5/32” hex Allen wrench to turn the Allen screws (item G) 1 to 2 turns counter-
clockwise if the Fowler will not move or 1 to 2 turns clockwise if the Fowler will not hold its position.
5. Retighten the nuts. Be sure the Fowler will travel from flat to 90 degrees and down again and will hold its
position when weight is applied before returning the stretcher to service.
FOLDDOWN SIDERAIL LATCH ADJUSTMENT
Required Tools:
1/8 Hex Allen Wrench
WARNING
The siderail latch adjustment is pre−set at the factory, and there should not normally be a need for readjust-
ment. If adjustment must be done it is important to follow the procedure below. If it is not done properly, injury
to the patient or user could occur.
Adjustment Procedure:
1. Using a 1/8 hex Allen wrench, adjust the hex Allen screw located on the latch assembly opposite the latch.
Turning the Allen screw clockwise will DECREASEthe amount of ”play” in the latching mechanism. Turn-
ing counterclockwise will INCREASE the amount.
NOTE
The amount of ”play” in the siderail, when in full up engaged position, should be approximately 1/8 to 3/16
inches.
CAUTION
Too much ”play” when the siderail is in the full up engaged position will give the siderail the appearance of
being unstable and could also cause premature wearing of the latch system. Too little ”play” will obstruct
the latch and keep it from engaging completely in the full up position, which may cause damage to the latch
and/or injury to the patient or user.
Return to Table of Contents
Back to Table of Contents

6
Service Information
CASTER MAINTENANCE
Required Tools:
5/8” Wrench
11/16” Wrench
MAINTENANCE PROCEDURE
1. Using the 5/8” wrench and the 11/16” wrench, remove the centerlock nut (item A) from the through bolt
(item B) for the caster wheel.
2. Support the corner of the stretcher where the wheel is being removed and remove the through bolt (item
B) and the molded wheel (item C) .
3. Clean the through bolt, molded wheel, and the inside of the caster horn (item D) removing any dirt and
debris. Ensure the bearings in the molded wheel spin freely and easily.
4. Replace the molded wheel and the through bolt.
5. Replace the centerlock nut on the through bolt and use the 5/8” and 11/16” wrenches to tighten it securely.
Return to Table of Contents
Back to Table of Contents

7
Service Information
BRAKE CAM REPLACEMENT
Required Tools:
1/8” Allen Wrench String or Bungee Cord 3/32” Allen Wrench
Procedure:
1. Lift and support the base hood using string or bungee cord.
2. Using a 3/32” Allen wrench, loosen the set screw holding the brake adjuster to the brake ring and turn the
adjuster clockwise to remove it.
3. Using a 1/8” Allen wrench, remove the shoulder bolt and nut holding the brake link on the cam and remove
the cam.
4. Reverse steps 3 and 4 to install the new cam. Apply and release the brakes to assure they operate properly.
If adjustment is required, see page 13. Reinstall the base hood.
BRAKE RING REPLACEMENT
Brake Ring Part Number 1080−2−50
Required Tools:
(2) 7/16” Wrenches String or Bungee Cord Floor Jack, Small Crate (or equiv.)
Large Standard Screwdriver 3/32” Allen Wrench 3/4” Socket & Ratchet
3/4” Wrench Needle−Nose Pliers
Procedure:
1. Lift and support the base hood using string or bungee cord. Put the brake/steer pedal in the neutral position.
Lift the end of the base needing service until the casters are approximately 12” off the floor and support
it with a jack or the equivalent.
2. Using a 3/32” Allen wrench, loosen the set screw holding the brake adjuster to the brake ring and turn the
adjuster clockwise to remove it.
3. Remove both of the caster wheels on the end of the stretcher needing service (see page 6). Use a 3/4”
socket and a ratchet inside the caster horn and a 3/4” wrench on the caster nut to remove the bolt and
the caster horn.
4. Using needle−nose pliers, carefully squeeze and remove the spring between the brake cam and the brake
ring.
WARNING
The spring is tightly compressed. Use caution when removing it or personal injury could result.
5. Remove the spring from the pump pedal.
6. Lower the brake ring and remove it from the base. Remove the brake pads and bushings and install them
on the new brake ring.
7. Reverse the above steps to install the new brake ring and reinstall the caster and wheel. Apply and release
the brakes to assure they operate properly. If adjustment is required, see page 13. Reinstall the base
hood.
NOTE
For easier access when installing the set screw holding the brake adjuster, be sure the set screw hole in the
brake ring collar is facing toward the inside of the base when installing the new brake ring.
Return to Table of Contents
Back to Table of Contents

8
Service Information
BRAKE/STEER PEDAL REPLACEMENT
Required Tools:
Two (2) 7/16” Wrenches 3/16” Drive Pin Loctite 409 or Equivalent
Hammer 3/8” Box End Wrench Bungee Cords or String
Replacement Procedure:
NOTE
It may require two people to safely perform this procedure.
1. Apply the brakes, if possible, with the remaining good brake/steer pedal. If this is not possible, have some-
one assist you with the following: Using a large wrench or pry tool, push down on the brake bar (compressing
the spring) and manually move the molded plastic brake cam over to the brake position at both ends of the
base.
2. Raise the litter to full up. Raise the Fowler and the siderails.
3. Suspend the base hood from the litter and out of the way with bungee cords. Or, for better access, remove
the litter by following the next 3 steps.
4. Using a 3/8” wrench, remove the bolt in the litter support tube above the black bellows on both ends.
5. With the assistance of another person, lift off the stretcher litter and set it aside, taking care not to damage
the litter components.
6. Lift off the plastic base hood, separating the Velcro holding it to the base frame.
7. Using the 7/16” wrenches, remove the bolt, nut and washers holding the square brake drive link assembly
on the brake actuator on both sides of the base.
8. While lifting one end (head or foot) of the base, rotate the brake/steer pedal so its bottom is facing up.
9. Use a hammer and 3/16” drive pin to remove the groove pin from the plastic brake/steer pedal. Be sure
that you are driving the pin out from the bottom of the pedal towards the top of the pedal.
10. Once the groove pin has been removed, remove the brake/steer pedal from the brake rod (use of a ham-
mer may be required).
11. Repeat step 8 so the brake actuators are upright.
12. Fit the replacement brake/steer pedal onto the brake rod.
13. Align the holes in the brake/steer pedal with the holes in the brake rod. Apply Loctite #409 to the replace-
ment groove pin and use a hammer to install it. Drive the pin in from the top of the pedal until it is flush to
the top of the pedal.
14. Reverse step 7 to reattach both brake drive link assemblies to the base (When the pedal is reconnected
it will already be in the brake position).
15. Actuate the brake/steer pedal to ensure the unit functions fully in brake, neutral and steer modes.
16. Reinstall the base hood, securing it to the Velcro.
17. With the assistance of another person, place the litter back on the base (if necessary).
18. Use a 3/8” wrench to install the bolts in the litter support tubes above the black bellows on both ends of
the litter.
Return to Table of Contents
Back to Table of Contents

9
Service Information
HYDRAULIC SYSTEM TROUBLESHOOTING
PROBLEM/SYMPTOM POSSIBLE CAUSE SOLUTION
Jack will not raise to full
height. Reservoir low on hydraulic fluid. Add hydraulic fluid (see page 12).
One end of stretcher rises
much slower than the other
end.
Air in pump piston.
Reservoir low on hydraulic fluid.
Prime pump (see page 12)).
Add hydraulic fluid (see page 12)).
Jack will not pump up. Lever assembly is in contact with
valve stem on manifold assembly.
Air in pump piston.
Defective jack.
Adjust length of control rod so
there is a slight gap between lever
and valve stem.
Prime pump (see page 12)).
Replace jack.
Jack will not hold in raised
position. Lever assembly is in contact with valve stem on manifold assembly.
Defective valve.
Defective jack.
Internal leakage of oil past a valve
or seal.
Adjust length of control rod so
there is a slight gap between lever
and valve stem.
Fully elevate jack. Close needle
valve by turning clockwise. If jack
no longer sinks, needle valve is
defective. Replace needle valve
(part # 962−1−152).
Fully elevate jack. Close needle
valve by turning clockwise. If jack
continues to sink, jack is defec-
tive. Replace jack.
Assure all valves are fully closed
by depressing and releasing ap-
propriate pedal. Assure there is a
slight gap between the lever as-
sembly and the valve stem. Close
the needle valve completely. If
the jack holds, the leakage is in
the release valve and the valve
should be replaced.
Jack will not lower. Valve support is loose and out of
position. Reposition valve support and tighten screws.
Contact Stryker technical service at 1−800−327−0770 for further assistance.
Return to Table of Contents
Back to Table of Contents

10
Service Information
JACK REPLACEMENT
Required Tools:
7/16” Wrench 7/16” Socket 6” Extension & Ratchet
5/32” Allen Wrench 3/8” Box End Wrench Bungee Cords or String
1/2” Wrench 3/16” Allen Wrench Spring Compression Tool
Refer to assembly drawing number 1080−1−10, pages 15−19 for part identification.
Replacement Procedure:
1. Apply the stretcher brakes. Using a 3/8” box end wrench, remove square head set screws from both head
and foot end jack support tubes. Remove litter top and set aside.
2. Lift up the base hood at the end of the stretcher needing service, separating the Velcro holding the hood
to the base frame and remove the base hood from the stretcher base.
3. Using a 1/2” wrench, remove the screws (item DT), external tooth lock washers (item DC), and nylock nuts
(item CS) holding the pump link roller bar assembly (items K, L, & BU) to the base.
4. Using a 1/2” wrench and a 3/16” Allen wrench, remove the shoulder screws (item DP), washers (item DA)
and nylock nuts (item CS) holding the link to the pump bar weldment (item N).
5. Use the spring compression tool (p/n 1210−1−3) to compress the spring or the pump piston could be pulled
out of the pump resulting in excessive hydraulic fluid loss. Using a 1/2” wrench, remove the nylock nut
(item CS) and the washer (item DA) from the base stud and remove the two pump links (item S & T) which
are still attached to each other.
6. With the spring compression tool still in place, remove the pump link weldment (item M). Carefully remove
the spring compression tool.
WARNING
Use extreme caution when removing the pump compression tool. The spring and top spring guide are still
under pressure and could cause personal injury if they are allowed to come free.
7. Remove the spring guide (item AZ), the spring (item CB), the spring holder guide (item AY) and the jack
washer from the jack pump.
8. Using two 1/2” wrenches, remove the screws (item DT), lock washers (item DC), and nylock nuts (item
CS) holding the jack support bracket (item AM) to the frame.
9. Using a 3/8” wrench and a 5/32” Allen wrench, remove the screws (item DS) and nylock nuts (item CU)
holding the jack manifold to the base.
10. Using a 7/16” wrench, a 7/16” socket, and a 6” extension with ratchet, remove the screws (item DW),
washers (item DH), and nylock nuts (item CT) holding the jack assembly to the base.
11. Install the replacement jack assembly and secure it with the four screws, washers and nuts.
12. Using a 3/8” wrench and a 5/32” Allen wrench, mount the jack manifold to the base with the two screws
and nylock nuts. Put the release valve stop ring (item BF) onto the descent valve plunger. Turn the
descent valve clockwise to close it completely then open it one half turn (counterclockwise).
Return to Table of Contents
Back to Table of Contents

11
Service Information
JACK REPLACEMENT (CONTINUED)
Replacement Procedure (Continued):
13. Place the jack support bracket on the jack. Use a 1/2” wrench to secure it to the jack with the screws,
lock washers and nylock nuts removed in step 8. To avoid damage to the base hood, insert the screws
from the outside of the frame and the lock washers and the nuts on the inside.
CAUTION
Tighten the support bracket screws securely. Do not over tighten the screws or the jack reservoir tube could
be damaged.
14. Install the jack washer (item BR) onto the new jack. Apply grease to the bottom spring holder guide (item
AY). Place the bottom spring holder guide, the spring (item CB) and the top spring holder guide onto
the jack pump. Compress the spring with the spring compression tool (part number 1210−1−3).
15. Reinstall the pump link (item M) into the hole in the pump piston. Apply grease to the base where the
pump link contacts it.
16. Reinstall the links removed in step 5 to the base stud. Be sure the lower pump link pin is through the
center hole of the horizontal link (item S) and the swing link (item T) on the correct side of the horizontal
link (opposite the side the pump link is on). Install the washer (item DA) and the nylock nut (item CS)
onto the base stud (over the horizontal link) and tighten them securely being sure the link still pivots freely.
17. Using a 1/2” wrench, reattach the roller bar assembly (items K, L, & BU − removed in step 3) with the
hardware (items DT, DC, & CS). Replace the bearings in the ends of the roller bar, if necessary. The
roller bar assembly should be firmly against the pump link. To avoid damage to the base hood, insert
the screw from the outside of the frame and the lock washer and the nut on the inside.
18. With a 1/2” wrench and a 3/16” Allen wrench, assemble the swing link (item T) to the pump bar weldment
(item N) using the shoulder screw (item DP), washer (item DA), and nylock nut (item CS).
19. Pump up the jack to the maximum height. Apply weight and ensure the jack holds its position and there
are no hydraulic leaks before replacing the base hood and the litter. Reinstall the base hood and the litter
top. Test the stretcher for proper operation before putting it back into service.
Return to Table of Contents
Back to Table of Contents

12
Service Information
CHECKING HYDRAULIC FLUID LEVEL
1. Lower jack completely.
2. Remove fill plug on side of jack.
3. The hydraulic fluid should be visible at the bottom of the fill hole. If it is not, add Mobil Aero HFA hydraulic
fluid (Stryker p/n 2020−70−475) until the fluid is visible at the bottom of the fill hole. Replace the fill plug.
CAUTION
Use of other types of oil may damage hydraulic units.
PRIMING PUMP
1. Remove the pump link and the spring (see page 10, steps 1−6).
CAUTION
Pump link is spring loaded.
2. To remove air, actuate pump by hand, making sure the pump piston bottoms. Reassemble (see page 10
& 11) and check for leaks.
REMOVAL OF EXCESS AIR (VACUUM) FROM THE HYDRAULIC SYSTEM
Procedure:
1. Verify all hydraulic linkages are secure and operating properly.
2. Using pump pedal, actuate system several times. This will force the air through the system and the jack
should now pump up.
MATTRESS MAINTENANCE
1. Mattresses should be routinely checked to ensure they are free of cracks or tears in the covers and that
the Velcro on the mattress as well as the litter is in good condition.
2. If any of the litter Velcro needs to be replaced, remove the damaged Velcro from the litter and replace it
with part number 381−24−7 cut to length.
Return to Table of Contents
Back to Table of Contents

13
Service Information
BRAKE ADJUSTMENT
R
equired Tools:
3
/32” Hex Allen Wrench
P
ry Bar
BASE LUBRICATION POINTS
1. Lubricate brake adjuster rod
around areas shown at both ends
of the stretcher with MPG−2
Do not grease
area shown.
grease or the equivalent.
Remove retaining plates, lift
the pump bar weldment and
grease the pump bar pivot
brackets.
Grease retaining plates where
they come in contact with the
pump bar before replacing them.
Return to Table of Contents
Back to Table of Contents

14
Quick Reference Replacement Parts List
PART NAME PART NUMBER
Brake Adjuster Assembly 715−201−150. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Adjuster Service Tool 715−700−150. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Caster Wheel Assembly 1080−5−10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foot Board/Chart Holder 1080−134. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fowler Pneumatic Cylinder 1010−31−78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Jack Assembly 1080−70−10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Seal Kit 390−2−183. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Release Valve Assembly 962−1−152. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack Pump Spring Compression Tool 1210−1−3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I.V. Pole, Standard Removable 390−25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I.V. Pole, Permanently Attached, Head End 1080−110. . . . . . . . . . . . . . . . . . . . . . . . .
I.V. Pole, Permanently Attached, Foot End 1080−112. . . . . . . . . . . . . . . . . . . . . . . . . .
Oxygen Bottle Holder 1020−30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mattress, 2” Conductive 1080−226−210. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paint, Touch−Up, Gloss Black, Bottle w/Brush 7000−1−322. . . . . . . . . . . . . . . . . . . . . . .
Paint, Touch−Up, Gloss Black, Spray Can 7000−1−319. . . . . . . . . . . . . . . . . . . . . . . . . . .
Paint, Touch−Up, Gray, Bottle w/Brush 7000−1−320. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paint, Touch−Up, Gray, Spray Can 7000−1−317. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restraint Straps, Ankle 946−43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restraint Straps, Body 390−19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restraint Straps, Wrist 946−44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restraint Straps, Full Patient Restraint Package 1010−77. . . . . . . . . . . . . . . . . . . . .
Return to Table of Contents
Back to Table of Contents

15
Base Assembly
Assembly part number 1080−1−10 (reference only)
Return to Table of Contents

16
Base Assembly
Return to Table of Contents

17
Base Assembly
Return to Table of Contents

18
Base Assembly
Return to Table of Contents