Stryker MedSurg Standard 3002 S3 User manual

2009/09 3006-109-006 REV B www.stryker.com
Maintenance Manual
For technical assistance
USA: 1-800-327-0770 (option 2)
MedSurg Bed
Model 3002 S3
International 230V

www.stryker.com 3006-109-006 REV B 3
Table of Contents
Introduction ..............................................................................7
IntendedUse..........................................................................7
Specifications.........................................................................7
MattressSpecifications..................................................................7
EnvironmentalConditions.................................................................8
Warning/Caution/NoteDefinition............................................................8
BedIllustration............................................................................9
Symbols................................................................................10
SafetyTipsandGuidelines..................................................................11
iBED AwarenessOption................................................................. 13
StaticDischargePrecautions ................................................................14
SetupProcedures.........................................................................15
MaintenanceMenuGuide...................................................................16
MaintenanceMenuScreen ..............................................................16
Cleaning................................................................................22
PreventativeMaintenance...................................................................23
Checklist............................................................................23
GreasePoints........................................................................24
TroubleshootingGuide.....................................................................25
iBEDAwarenessSystemErrorCodes..........................................................28
ErrorHandling .......................................................................28
LoggedErrors........................................................................28
ErrorMessages.......................................................................29
QuickReferenceReplacementPartsList .......................................................32
ServiceInformation........................................................................34
BrakePedalReplacement...............................................................34
LiftMotorandCapacitorRemovalandReplacement............................................35
LiftHousingRemovalandReplacement.....................................................36
LiftPotentiometerReplacementandAdjustment...............................................38
LiftPotentiometer“Burn-in”Procedure......................................................39
LiftMotorIsolationPlateReplacement......................................................40
LiftMotorCouplerReplacement...........................................................41
PowerandSensorCoilCordReplacement...................................................42
PowerandSensorCoilCordReplacementIllustration...........................................43
KneeMotorRemovalandReplacement .....................................................44
FowlerMotorCAMandCAMGuideReplacement..............................................45
LimitSetting-FowlerMotor..............................................................46
FowlerMotorRemovalandReplacement....................................................47
Fowler Motor Drive Isolator and CPR Decoupler Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 48
FowlerMotorBallScrewAssemblyReplacement ..............................................49
HeadMotorBrake/ClutchReplacement .....................................................50
LoadCellReplacement.................................................................51
LoadCellReplacement-GreasePoints.....................................................52
PowerSupplyReplacement..............................................................53

4 3006-109-006 REV B www.stryker.com
Table of Contents
Service Information (Continued)
CPUBoardReplacement................................................................53
SoftConfig.Procedures.................................................................54
OptionalSmartTVInterface“Burn-In”Procedure..............................................65
FowlerPotentiometerReplacement ........................................................66
FowlerPotentiometer“Burn-In”Procedure...................................................66
HeadandFootSiderailCoverRemoval......................................................67
HeadSiderailHoopReplacement..........................................................68
FootboardModuleRemoval..............................................................69
FootboardInterfacePlugReplacement......................................................70
BedCircuitBoards........................................................................71
CPUBoard-3006-307-900..............................................................71
CPUBoard-3006-307-900(Continued).....................................................72
SoftwareConfiguration..................................................................73
PowerSupply-0059-157-000.............................................................74
iBed Enhanced Nurse Call Option, 37-Pin Plugover Board - 3006-303-900 . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
iBed Enhanced Nurse Call Option, Dip-Switch Settings (Default). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
HeadWallOutputConfiguration ..............................................................78
AssemblyDrawings .......................................................................79
BedAssembly,StandardBed.............................................................79
Bed Assembly, iBedAwarenessOption......................................................85
BaseAssembly,StandardBed............................................................87
BrakePlateAssembly ..................................................................96
LiftAssembly(HeadandFootEnd) ........................................................97
LiftAssembly.........................................................................98
MotorIsolationPlateAssembly...........................................................102
BrakeShaftAssembly,StandardBed......................................................103
BrakeCrankAssembly................................................................. 104
BrakeBarAssembly...................................................................105
SwivelLockCasterAssembly-3006-200-060...............................................106
SteerSwivelCasterAssembly-3006-200-065...............................................107
6”MoldedWheelAssembly-5000-002-010.................................................108
BottomCover-3001-200-022 ........................................................... 109
LitterAssembly,StandardComponents.....................................................110
Litter Assembly, Standard Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Foot Prop Assembly, Standard Length Bed - 3003-034-010. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
LitterCPUCoverAssembly-3001-300-097................................................. 123
FootCoverAssembly-3003-300-042 ..................................................... 124
ElectricalLitterAssembly,StandardBed.................................................... 125
Mechanical Litter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
LiftHeaderAssembly-NoLoadCells ..................................................... 137
LiftHeaderAssemblywithLoadCells...................................................... 138
GatchMotorAssembly-3006-375-420 .................................................... 139
FowlerDriveAssembly................................................................. 140

www.stryker.com 3006-109-006 REV B 5
Table of Contents
Assembly Drawings (Continued)
FowlerActuatorAssembly-3006-375-705.................................................. 142
FowlerBrakeKitAssembly-3001-300-775..................................................143
FowlerLimitSwitchAssembly-3002-343-035............................................... 144
NightLightAssembly-3006-410-020...................................................... 146
OptionalScale/BedExitAssembly........................................................ 148
Optional Litter Assembly, Nurse Call and Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
OptionalLitterAssembly,HWIwith1StrykerPort............................................. 152
Optional iBed Enhanced Nurse Call, 37-Pin Plugover Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
BatteryEnclosureAssembly............................................................. 156
HeadEndSiderailAssembly............................................................. 157
HeadEndSiderailAssembly,StandardOptions...............................................166
HeadEndSiderailAssembly,OuterPanel................................................... 170
HeadEndSiderailAssembly,InnerPanel................................................... 171
Siderail Ass’y, iBED Awareness Option, HE, Left - 3006-400-100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Siderail Ass’y, iBED Awareness Option, HE, Right - 3006-400-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
SwitchAssembly,iBEDAwarenessOption,HeadEnd.......................................... 175
3006-400-120(Left)/3006-400-220(Right)................................................. 175
FootEndSiderailAssembly............................................................. 177
Siderail Ass’y, iBED Awareness Option, FE Left - 3006-400-305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Siderail Ass’y, iBED Awareness Option, FE, Right - 3006-400-405 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
SwitchAssembly,iBEDAwarenessOption,FootEnd .......................................... 187
3006-400-315(Left)/3006-400-415(Right)................................................. 187
Optional Pendant Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
FootboardAssembly,Standard........................................................... 189
FootboardPumpRackAssembly .........................................................191
FootboardModuleAssembly ............................................................192
FootboardAssembly,NoOptions-3006-500-104.............................................193
FootboardAssembly,BedExitOption-3006-500-105..........................................195
Footboard Assembly, Bed Exit/Scale Option - 3006-500-107 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Footboard Assembly, Bed Exit/Zone Control Option - 3006-500-106 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Footboard Assembly, Bed Exit/Scale/Zone Option - 3006-500-109 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Footboard Assembly, iBEDAwarenessOption-3006-500-100 ...................................203
HeadBoardAssembly-3006-600-010.....................................................205
OptionalCPRBoardAssembly-3006-626-010...............................................207
Optional Removable I.V. Pole and Mounting Ass’y - 3001-338-010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
RemovableI.V.PoleAssembly-3000-300-080...............................................209
Optional2-StageI.V.PoleAssembly-2035-112-000........................................... 210
Optional Dual Head End I.V. Pole Assembly - 2035-113-000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
2-StageI.V.Pole-2035-112-010&2035-113-011.............................................. 212
I.V.PoleLatchAssembly-0785-035-103 ................................................... 213
Optional Defibrillator Tray Assembly - 3006-120-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Optional Pleur-Evac Rack with Defibrillator Tray - 2040-120-004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Optional Upright O2 Bottle Holder Assembly - 3006-150-000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

6 3006-109-006 REV B www.stryker.com
Table of Contents
OptionalAccessoryAdapterFrame-3006-333-000........................................... 218
OptionalLitterRollerAssembly-3006-335-000.............................................. 219
RollerAssembly-3006-335-005.........................................................220
OptionalBedExtenderAssembly-3006-346-020.............................................221
OptionalBedExtenderMattress-3000-318-050 .............................................223
OptionalTractionSocketExtensions.......................................................224
Warranty ..............................................................................225
LimitedWarranty.....................................................................225
ToObtainPartsandService ............................................................225
ServiceContractCoverage .............................................................225
ServiceContractprograms..............................................................226
ReturnAuthorization...................................................................226
DamagedMerchandise ................................................................226
InternationalWarrantyClause............................................................226
EMCInformation.........................................................................227
RecyclingPassport ......................................................................231

Return To Table of Contents
www.stryker.com 3006-109-006 REV B 7
Introduction
SPECIFICATIONS
Safe Working Load
Note: Safe Working Load indicates the sum of the
patient, mattress, and accessory weight.
500 lbs 227 kg
Scale System Capacity (optional equipment). Loads weighing up to 500 lbs 227 kg
Scale System Accuracy (optional equipment)
± 2 pounds at 0° - ± 10° Trendelenburg for
patients weighing 100 pounds or less
± 2% of the total patient weight at 0° - ± 10°
Trendelenburg for patients weighing greater
than 100 pounds
Overall Length/Width - Standard Bed Siderails Up 93” x 41-1/2” 236,2 cm x 105,41 cm
Siderails Down 93” x 3-1/2” 236,2 cm x 100,3 cm
Patient Sleep Surface - Standard Bed 84” x 35” 213,4 cm x 88,9 cm
Bed Height to Top of Seat Litter - 6” Casters 16” to 30” ±0.5 40,6 cm to 76,2 cm
Litter Platform to Top of
Siderail
Full Up Head End Siderail 15” 38,1 cm
Full Up Foot End Siderail 15-1/2” 39,37 cm
Space Between Siderails (Full Up) 2-1/4” 5,72 cm
Knee Gatch Angle 0° to 45°
Fowler Angle 0° to 60°
Trendelenburg/Reverse Trendelenburg +12° to -10° ± 1°
Electrical Requirements 230 VAC, 50/60 Hz, 8.0 A
Battery Voltage (1) 9V Nurse Call Option (Alkaline Battery)
MATTRESS SPECIFICATIONS
Thickness 6” 15,2 cm
Width >= 35” >= 88,9 cm
Length >= 84” >= 213,4 cm
ILD 80 lbs 36.3 kg
The above stated mattress specifications assist in ensuring the product conforms to HBSW and IEC
specifications.
INTENDED USE
This manual is designed to assist you with the operation of the Model 3002 S3 MedSurg Bed. Read it thoroughly before
using the equipment.

Return To Table of Contents
8 3006-109-006 REV B www.stryker.com
ENVIRONMENTAL CONDITIONS
Environmental Conditions Operation Storage and Transportation
Ambient Temperature
Relative Humidity
(Non-Condensing)
Atmospheric Pressure
Stryker reserves the right to change specifications without notice.
Specifications listed are approximate and may vary slightly from unit to unit or by power supply fluctuations.
WARNING/CAUTION/NOTE DEFINITION
The words Warning, Caution and Note carry special meanings and should be carefully reviewed.
WARNING
Alerts the reader about a situation, which if not avoided, could result in death or serious injury. It may also describe
potential serious adverse reactions and safety hazards.
CAUTION
Alerts the reader of a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury to
the user or patient or damage to the equipment or other property. This includes special care necessary for the safe
and effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use
or misuse.
Note
This provides special information to make maintenance easier or important instructions clearer.
Introduction
10 0C
40 0C
(50 0F)
(104 0F)
-30 0C
60 0C
(-22 0F)
(140 0F)
30%
75%
10%
95%
700 hPa
1060 hPa
500 hPa
1060 hPa

Return To Table of Contents
www.stryker.com 3006-109-006 REV B 9
Bed Illustration
Headboard
Brake
Pedal
Siderail Release
Handle
Siderail
Footboard
Caster
Footboard
Control Panel
Patient
Control Panel
Nurse
Control Panel
Steer
Pedal
(not
shown)

Return To Table of Contents
10 3006-109-006 REV B www.stryker.com
Symbols
Warning, consult accompanying documentation
Type B Equipment: equipment providing a particular degree of protection against electric shock,
particularly regarding allowable leakage current and reliability of the protective earth connection.
Alternating Current
Class 1 Equipment: equipment in which protection against electric shock does not rely on BASIC
INSULATION only, but which includes an additional safety precaution in that means are provided for the
connection of the EQUIPMENT to the protective earth conductor in the fixed wiring of the installation in
such a way that ACCESSIBLE METAL PARTS cannot become live in the event of a failure of the BASIC
INSULATION.
Mode of Operation: Continuous
Protection from liquid splash
Dangerous Voltage Symbol
Protective Earth Terminal
Safe Working Load Symbol
Potential Equalization Symbol
~
IPX4

Return To Table of Contents
www.stryker.com 3006-109-006 REV B 11
Before operating the 3002 S3 MedSurg Bed, it is important to read and understand all information in this manual.
Carefully read and strictly follow the safety guidelines listed on this page. It is important that all users have been trained
and educated on the inherent hazards associated with the usage of electric beds.
WARNING
• To prevent permanent damage to this unit, the unit must reach room temperature prior to conducting any setup
and/or unit operations.
• Danger: Explosion hazard. Do not use in the presence of flammable anesthetics. Always apply the caster brakes
when a patient is getting on or off the bed.
• Always keep the caster brakes applied when a patient is on the bed (except during transport). After the brake
pedal is applied, push on the bed to ensure the brakes are locked. Serious injury could result if the bed moves
while a patient is getting in or out of bed.
• Ensure the brakes are completely released prior to moving the unit. Attempting to move the unit with the brakes
actuated could result in injury to the user and/or patient.
• Do not attempt to move the foot end of the bed laterally when the steer pedal is activated. When the steer pedal
is activated, the steer caster at the foot end of the bed cannot swivel. Attempting to move the bed laterally when
the steer pedal is activated may cause injury to the user.
• The 3002 S3 MedSurg Bed is not intended for use with patients less than two years of age.
• Serious injury can result if caution is not used when operating the unit. Operate the unit only when all persons are
clear of the electrical and mechanical systems.
• To help reduce the number and severity of falls by patients, always leave the bed in the lowest position when the
patient is unattended.
• When attaching equipment to the frame, ensure it will not impede normal frame operation. For example: hooks
on hanging equipment must not actuate control buttons, equipment must not hide the nurse call button, foley bags
must not rest on brake pedal, etc. Use only a Stryker supplied interface cable. Use of any other cable may cause
the bed to function improperly, which may result in patient or user injury.
• The 3002 S3 MedSurg Bed is equipped with a hospital grade plug for protection against electric shock hazard. It
must be plugged directly into a properly grounded three prong receptacle. Grounding reliability can be achieved
only when a hospital grade receptacle is used.
• When raising the siderails, listen for the “click”. When raising the siderail, the first click will indicate you can return
to the intermediate position, the second click indicates its full up position. Once in position, move siderail from
side to side to ensure it is locked into position. Siderails are not intended to be a patient restraint device. It is the
responsibility of attending medical personnel to determine the degree of restraint and the siderail positioning to
ensure a patient will remain safely in bed.
• The Bed Exit System is intended only to aid in the detection of a patient exiting the unit. It is NOT intended
to replace patient monitoring protocol. The bed exit system signals when a patient is about to exit. Adding or
subtracting objects from the frame after zeroing the weigh system may cause a reduction in the sensitivity of the
bed exit system.
• Before servicing or cleaning the bed, always unplug the bed power cord from the wall socket. When working
under a bed in the high position, always place blocks under the litter frame and apply the brakes to prevent injury
in case the Bed Down switch is accidently pressed.
• To avoid pinching your fingers, place the I.V. pole in the upright position before using the drive handle.
• When using any mattress and/or mattress overlay that increases the overall height greater than 6,” extra caution
and/or operator supervision is required to help reduce the likelihood of a patient fall occurring.
Safety Tips and Guidelines

Return To Table of Contents
12 3006-109-006 REV B www.stryker.com
CAUTION
• When large spills occur in the area of the circuit boards, 230 volt cables and motors, immediately unplug the bed
power cord from the wall socket. Remove the patient from the bed and clean up the fluid. Have maintenance
completely check the bed. Fluids can affect the operational capabilities of any electrical product. DO NOT put
the bed back into service until it is completely dry and has been thoroughly tested for safe operation.
• Preventative maintenance should be performed at a minimum of annually to ensure all bed features are functioning
properly. Close attention should be given to safety features including, but not limited to, safety side latching
mechanisms, frayed electrical cords and components, all electrical controls returning to the off or neutral position
when released, caster braking systems, no controls or cabling entangled in bed mechanisms, leakage current 300
microamps maximum, scale and bed exit systems calibrated properly, and the siderail gas spring not leaking oil.
• Because individual beds may have different options, footboards should not be moved from one bed to another.
Mixing footboards could result in unpredictable bed operation.
• The lockout buttons on the footboard lock the Fowler, Gatch and Bed Up/Down functions and prevent motion of
the bed. It is the responsibility of attending medical personnel to determine whether these functions should be
locked and to use the buttons accordingly.
• The maximum safe working load for each I.V. pole is 40 pounds.
• I.V. Poles should not be used as a bed push/pull device.
• Scale function may be affected by siderail/caster interference. With the litter fully lowered or lowered in Reverse
Trendelenburg, the siderails tucked under the litter in the storage position and the casters turned, there is the
potential for interference between the siderail and the caster. Raise the siderails when lowering the litter to the full
down position to prevent the interference from causing the scale system to weigh inaccurately
• The use of a mattress overlay may reduce the effectiveness of the siderail.
• The cleanliness and integrity of both ground chains must be maintained to minimize static build up and
discharge.
• Do not add or remove weight when the bed exit system is armed.
• There is a possible fire hazard when using half bed length type oxygen administering equipment. Ensure that the
siderails are outside of the tent.
• There is a possible fire hazard when used with oxygen administering equipment of other than the nasal or mask
type. Lock the control at foot of bed when using oxygen administering equipment.
• The weight of the foley bags placed on isolated bag hooks should not exceed five pounds.
• The weight of pumps placed on footboard pump holder should not exceed 45 pounds.
Safety Tips and Guidelines

Return To Table of Contents
www.stryker.com 3006-109-006 REV B 13
Safety Tips and Guidelines
IBED AWARENESS OPTION
In addition to the previous warnings and cautions, all of the following warnings and cautions apply to units equipped
with the iBED Awareness option.
WARNING
• The optional iBED Awareness system only indicates the siderail position; it does NOT indicate if the siderail is
locked. It is the caregiver’s responsibility to ensure that the siderails are locked after every move and also before
leaving a patient in the room.
• The optional iBED Awareness system indicator lights are only an aid to the caregiver, and in no way replace the
caregiver’s responsibility of checking on patients. Caregivers should not rely on the lights to perform their duties.
• Before arming the optional iBED Awareness system, the nurse must physically verify that siderails are locked.
CAUTION
• If the optional iBED Awareness system is being used, ensure the bed is in the desirable state (iBED Awareness
ON and with the light green) before leaving the room.
• If the optional iBED Awareness system is being used and the iBED Awareness is alerting, do not turn off iBED
Awareness as the display information to troubleshoot the bed will get lost.
• If the optional iBED Awareness system is being used, use of accessories that cover the center and side alert lights
at the footboard are not recommended.

Return To Table of Contents
14 3006-109-006 REV B www.stryker.com
The electronic circuits in the 3002 S3 Bed are completely protected from static electricity damage only while the bed
is assembled. It is extremely important that all service personnel always use adequate static protection when servicing
the electronic systems of the 3002 S3 Bed. Whenever you are touching wires, you should be using static protection.
Static Protection Equipment
The necessary equipment for proper static protection is:
• 1 static wrist strap; 3M part number 2214 or equivalent,
• 1 grounding plug; 3M part number 61038 or equivalent,
• 1 test lead with a banana plug on one end and an alligator clip on the other; Smith part number N132B699 or
equivalent.
CAUTION
All electronic service parts will be shipped in static shielding bags. Do not open the bags until you have completed
steps 2 and 3 of the following procedure. Do not place unprotected circuit boards on the floor. All circuit boards to be
returned to Stryker Medical should be shipped in the static shielding bags the new boards were shipped in.
Static Protection Procedure
1. Unplug the power cord from the wall receptacle.
2. Insert the grounding plug into a properly grounded hospital grade wall receptacle. Plug the banana plug of the
test lead into the receptacle on the grounding plug. Connect the alligator clip on the other end of the test lead to
a ground point on the bed.
3. Place the static control wrist strap on your wrist. Connect the alligator clip at the other end of the wrist strap cord
to a ground point on the bed.
BED
GROUNDING DIAGRAM
Static Discharge Precautions

Return To Table of Contents
www.stryker.com 3006-109-006 REV B 15
To prevent permanent damage to this unit, the unit must reach room temperature prior to conducting any setup
and/or unit operations.
It is important that the 3002 S3 MedSurg Bed is working properly before it is put into service. The following list will
help ensure that each part of the bed is tested.
WARNING
• The 3002 S3 MedSurg is equipped with a hospital grade plug for protection against electric shock hazard. It must
be plugged directly into a properly grounded three prong receptacle. Grounding reliability can be achieved only
when a hospital grade receptacle is used.
• Use only a Stryker supplied interface cable. Use of any other cable may cause the bed to function improperly
which may result in patient or user injury.
• Ensure there is no patient on the bed during the setup procedure.
1. Plug the bed into a properly grounded, hospital grade wall receptacle and ensure the LED light at the foot
end of the bed comes on.
2. Plug the optional interface cable into the 37 pin connector under the litter frame at the head end of the bed, into
the “Patient Station”, “Head Wall”, “Docker Station”, or equivalent (whichever applies). Test the interface cable to
verify it is functioning properly.
3. Ensure the siderails raise, lower, lock in the up position, lock in the intermediate position when lowered and store
smoothly (see Operations Manual for further details).
4. Ensure that all four casters lock when the brake pedal is engaged ((see Operations Manual for further details).
5. Raise the fowler (head of bed) up to approximately 600. Squeeze the CPR release handle and ensure the back
will drop with minimal effort.
Note
Ensure that the “Brake” LED located on the outside of the head end siderails and on the footboard control panel
blink when the brakes are not engaged.
6. Perform each function on the footboard control panel to ensure that each function is working properly (see
Operations Manual for further details).
7. Perform each function on both head end siderails to ensure that each is working properly (see Operations Manual
for further details).
8. Activate the motion stop system to ensure it is functioning properly; press and hold down the BED DOWN key.
As the bed lowers, push up on the motion interrupt pan under the bed and ensure the downward motion stops.
Release the pan and allow the downward motion to continue.
Note
The bed’s upward motion or other functions are not disrupted by the motion stop system.
9. If the bed is equipped with the Nurse Call option, verify it is functioning properly prior to patient use.
Setup Procedures

Return To Table of Contents
16 3006-109-006 REV B www.stryker.com
MAINTENANCE MENU SCREEN
The Maintenance Menu contains all of the non-regularly accessible features of the product. This menu provides
an interface to the user and/or service personnel in order to provide the ability to control and access maintenance
features.
Maintenance Menu Items
The following are menu items listed in the maintenance menu screen for a fully loaded bed:
1. Calib. Scale (Calibrate Scale)
2. TV Config. (TV Configuration)
3. Scale Info. (Scale Info/Stats)
4. Clear Scale Stats
5. Error Log (View Error Log)
6. Clear Errors (Clear Error Log)
7. Scale Units (Lock Scale Units)
8. About (About Product)
9. Exit Menu (Exit Maintenance)
The following are menu items listed in the maintenance menu screen for a standard bed:
1. TV Config. (TV Configuration)
2. Error Log (View Error Log)
3. Clear Errors (Clear Error Log)
4. About (About Product)
5. Exit Menu (Exit Maintenance)
The following are menu items listed in the maintenance menu screen for an iBed:
1. Calib. Scale (Calibrate Scale)
2. TV Config. (TV Configuration)
3. Scale Info. (Scale Info/Stats)
4. Clear Scale Stats (only if you have scale option)
5. Error Log (View Error Log)
6. Clear Errors (Clear Error Log)
7. Scale Units (Lock Scale Units)
8. About (About Product)
9. Exit Menu (Exit Maintenance)
• Each of the menu items provides the operator with a different function.
• Using the up and down menu buttons, you can scroll though the menu elements.
• To select a menu item, scroll to the desired menu item using the Up and Down menu button. When the desired
feature is highlighted, press the Enter/Check button. Depending on the feature, the display will move into the
sequence for the feature selected.
Load Cell Check (Where applicable: for beds with a minimum of Scale or either kind of Bed Exit)
• This feature automatically checks all four load cells to make sure they are working properly.
• The purpose of this feature is to provide a self diagnostic of the load cells.
• When maintenance is entered, a self-diagnostic feature should run and display results.
• While the procedure is running, the following message is displayed: “Load Cell Check”.
• Any load cell errors will be displayed as a message “Load Cell Error” and then, depending on the error, an HL,
HR, FL or FR will be displayed below the message. (Refer to the Error Handling Section).
• If no errors are present, then the maintenance menu will be displayed and menu items 1-9 above may be
accessed where applicable.
Maintenance Menu Guide

Return To Table of Contents
www.stryker.com 3006-109-006 REV B 17
• This feature allows the operator to calibrate the scale system.
• This calibration is used to provide the system with a weight offset that occurs when the product is put into
trend and reverse trend.
• This calibration does not calibrate the load cells; the load cells are pre-calibrated.
To calibrate the scale system:
1. In the Maintenance Menu, select the Calibrate Scale item; then press and hold the Enter/Check button.
2. The display should present the following message:
“Do Not Touch Bed”. The message should be flashing.
3. Use the up and down arrow to select the proper weight (50lbs is the default).
4. Press the “Enter/Check” button when the display shows the proper weight.
5. The display should present the following message:
“Place Weight in Center”.
6. Place the weight in the center of the bed.
7. Press the “Enter/Check” button when completed.
8. The display should present the following message:
“Press Reverse Trend”.
9. Press the reverse trend button.
10. The display should present the following message when the bed is in the proper position:
“Release Button”.
11. Release the button and do not touch the bed. When the button is released, the following message is displayed:
“Do Not Touch Bed”. The message should be flashing.
12. The display should present the following message when the bed is ready to continue:
“Press Trend”.
13. Press the trend button.
14. The display should present the following message when the bed in the proper position:
“Release Button”.
15. Release the button and do not touch the bed. When the button is released the following message is displayed:
“Do Not Touch Bed”. The message should be flashing.
16. The display should present the following message when the bed is ready to continue:
“Save Calibration?”.
17. Press the “Enter/Check” button to save the calibration.
18. The display should present the following message when the bed is ready to continue:
“Save Successful”.
Note:
If an error occurs during the procedure the display will show an error message, “Calibration Error,” for four
seconds.
WARNING
Ensure there is no patient on the bed while the calibration procedure is being performed.
Maintenance Menu (Continued)
Calibrate Scale
Maintenance Menu Guide

Return To Table of Contents
18 3006-109-006 REV B www.stryker.com
TV Configuration
• This feature allows the operator to set up the TV configuration.
• This configuration provides the product with the information to communicate with the proper entertainment
system.
To Configure the System:
1. In the Maintenance Menu, select the TV Config. item; then press and hold the Enter/Check button.
2. The TV Configuration Screen will be displayed. The current TV selection will be highlighted.
3. Use the up and down arrow buttons to highlight the desired item.
4. Press the “Enter/Check” button to select the new setting.
5. The following message will be shown on the display screen when the new setting is saved:
“Save Successful”.
6. The TV Configuration screen should reappear after two seconds and the new setting should be highlighted.
7. If you press the Exit/X button or if the screen remains dormant for more than 30 seconds, the display will
return you to the maintenance menu without saving any changes.
Maintenance Menu (Continued)
Maintenance Menu Guide
TV
Config
Note: The user will use the arrow buttons to select the option . The selected item on
initialization will be the item that is currently set. If the user presses the ‘Enter’ button
then the new setting will be saved. If the user presses the ‘Exit’ button or the menu
times out (30 seconds after last button press) then the old setting will remain and the
screen will return to the ‘Maintenance menu’.
Accept Cancel Arrow
Up
Arrow
Down
Scroll Display Selected
Item Up One item.
Scroll Display Selected
Item Down One item.
Display = “Save
Successful” (Hold
message for 2 seconds)
Is ‘New’ SettingYes
No
Return to Maintenance
Menu
TV Config. 1
TV Config. 2
TV Config. 3
TV Config. 4
TV Config. 5
TV Config. 6
Traditional
Traditional Plus
Auto-Config.
Auto-Config. DV
Menu Items

Return To Table of Contents
www.stryker.com 3006-109-006 REV B 19
Scale Information
• This diagnostic feature shows data from the load cells. This includes the raw count data, the weight data (in
lb), the maximums and the minimums.
• When the menu item is selected, the weight data from the four load cells will be displayed.
• When cancel/exit is pressed, the menu should return.
• Values should update every 0.25 seconds.
Note: The scale information and statistics are important when trying to diagnose the scale system.
To View the Scale Information:
1. In the Maintenance Menu select the Scale Info item; then press and hold the Enter/Check button.
2. The Scale Info screen will be displayed.
3. Use the arrows to navigate through the four screens: lb, counts, maximums, and minimums. Each screen will
have the four load cells and the information in the format of that screen.
4. Press the Exit/X button to return to the Maintenance Menu screen.
Clear Scale Stats
• This diagnostic feature allows the statistics for the load cells to be cleared.
• This is done to remove old data. This may be done because the load cell is being replaced or the system has
been re-calibrated.
• When the menu item is selected and held for one second, the statistics should be erased and a message
should be displayed. When cancel/exit is pressed, the menu should return to the Maintenance Menu Screen.
Note: The scale statistics (Maximums and Minimums) can be cleared using this feature.
To Clear the Information:
1. In the Maintenance Menu, select the Clear Scale Stats item; then press and hold the Enter/Check button.
2. The following message will be shown on the display screen:
“Clear Scale Statistics?”
Maintenance Menu (Continued)
Maintenance Menu Guide

Return To Table of Contents
20 3006-109-006 REV B www.stryker.com
3. Press and hold the Enter/Check button to clear the stats.
4. The following message will be shown on the display screen when the stats are cleared:
“Statistics Cleared”.
5. The Maintenance Menu screen should reappear after two seconds
and the new setting should be highlighted.
Note: Items that are cleared during this operation are:
• Maximums (for each load cell)
• Minimums (for each load cell)
Error Log
• This feature allows the operator to view the Error Log.
• This log provides information pertaining to the error system and any errors that are logged during product
use.
To view the error log:
1. In the Maintenance Menu, select the Error Log item; then press the Enter/Check button.
2. The Error Log screen will be displayed. The most recent error will be at the top.
3. Use the up and down arrow buttons to view any errors that are not shown on the screen.
4. Pressing the Exit/X button will return you to the Maintenance Menu screen.
5. If the screen remains dormant for more than 30 seconds, you will be returned to the Maintenance Menu
screen.
Clear Errors
This feature allows the user to clear the error log.
To clear the error log:
1. In the Maintenance Menu, select the Clear Errors item; then press and hold the Enter/Check button.
2. The following confirmation screen will be displayed:
“Clear Error Log?”
3. If ‘Exit’ is chosen, you will be returned to the Maintenance Menu screen.
4. If ‘Enter’ is chosen, then the error log is cleared and a message is displayed: “Error Log Cleared”; you will
be returned to the Maintenance Menu screen.
Scale Units
• This feature allows the user to lock and/or unlock the unit of weight measurement as well as select the default
scale units (lb or kg).
• When the Scale Units menu item is selected, the unit of measure will be locked and the current unit of mea-
sure will be displayed.
• When cancel/exit is pressed, the menu will return to the Maintenance Menu Screen.
• The default setting is Unlocked.
To lock/unlock the Scale Units:
1. In the Maintenance Menu, select the Scale Units item; then press and hold the Enter/Check button.
2. The Scale Units Screen will display Figure 41 with the current state as the highlighted item.
Maintenance Menu (Continued)
Maintenance Menu Guide