Stryker Performance-LOAD User manual

PPeerrffoorrmmaannccee--LLOOAADD™™ CCoott FFaasstteenneerr SSyysstteemm
MMaaiinntteennaannccee MMaannuuaall
6392
EN
6392-009-002 Rev E.4 2018/06

SSyymmbboollss
Refer to instruction manual/booklet
Operating instructions/Consult instructions for use
General warning
Caution
Two person lift
Catalogue number

Serial number
 
For US Patents see www.stryker.com/patents
European authorized representative
Manufacturer
Date of manufacture
CE mark
Class II electrical equipment: equipment in which protection against electric shock does not rely
on basic insulation only, but in which additional safety precautions such as double insulation or
reinforced insulation are provided, there being no provision for protective earthing or reliance
upon installation conditions.
Direct current
Medical Equipment Recognized by Underwriters Laboratories LLC With Respect to Electric
Shock, Fire, and Mechanical Hazards only in accordance with ANSI/AAMI ES60601-1: 2005 and
CAN/CSA-C22.2 No. 60601-1:08.
IIPP2266 Protection from objects greater than 12.5 mm and powerful water jets
Medical Equipment Classified by Underwriters Laboratories Inc. With Respect to Electric Shock,
Fire, and Mechanical Hazards Only in Accordance with ANSI/AAMI ES60601-1: 2005 and CAN/
CSA-C22.2 No. 60601-1:08.
In accordance with European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment, this symbol indicates that the product must not be disposed of as unsorted municipal
waste, but should be collected separately. Refer to your local distributor for return and/or
collection systems available in your country.
This way up
6392-009-002 Rev E.4 EN

Fragile, handle with care
Keep dry
5
Do not stack more than 5 high
EN 6392-009-002 Rev E.4

TTaabbllee ooff CCoonntteennttss
Warning/Caution/Note Definition ..............................................................................................................................2
Summary of safety precautions ................................................................................................................................3
Introduction ...............................................................................................................................................................4
Product description .................................................................................................................................................4
Indications for use...................................................................................................................................................4
Expected service life ...............................................................................................................................................4
Contraindications....................................................................................................................................................4
Specifications .........................................................................................................................................................4
Standards with required options ...............................................................................................................................5
Product illustration ..................................................................................................................................................6
Important contact information...................................................................................................................................6
Contact information.................................................................................................................................................7
Serial number location.............................................................................................................................................7
Date of manufacture................................................................................................................................................7
Cleaning and disinfecting with wipes........................................................................................................................8
Cleaning....................................................................................................................................................................9
Disinfecting ............................................................................................................................................................9
Preventive maintenance .........................................................................................................................................10
Maintenance record ..............................................................................................................................................10
Training record .....................................................................................................................................................11
Troubleshooting ......................................................................................................................................................13
Inductive charging system does not charge the cot battery .......................................................................................13
Service ....................................................................................................................................................................14
Head end interface assembly replacement..............................................................................................................14
Foot end interface assembly replacement...............................................................................................................14
Inductive primary board replacement (optional) .......................................................................................................15
Head end plunger replacement ..............................................................................................................................16
Foot end lock pawl replacement.............................................................................................................................17
Safety bar rail support replacement ........................................................................................................................18
Foot end cover assembly replacement....................................................................................................................19
Performance-LOAD assembly................................................................................................................................21
Center cover assembly ...........................................................................................................................................24
Floor plate bolt assembly........................................................................................................................................25
Install kit assembly..................................................................................................................................................26
Inductive charging option........................................................................................................................................27
Foot end cover assembly........................................................................................................................................28
Foot end interface assembly ..................................................................................................................................29
Foot end nose assembly.........................................................................................................................................30
Guide rail assembly ................................................................................................................................................32
Head end cover assembly ......................................................................................................................................33
Head end interface assembly .................................................................................................................................34
Inductive charging assembly ..................................................................................................................................35
Head end hitch assembly .......................................................................................................................................36
Head end forging assembly....................................................................................................................................37
EMC information .....................................................................................................................................................38
6392-009-002 Rev E.4 1 EN

WWaarrnniinngg//CCaauuttiioonn//NNoottee DDeeffiinniittiioonn
The words WWAARRNNIINNGG,CCAAUUTTIIOONN, and NNOOTTEE carry special meanings and should be carefully reviewed.
WWAARRNNIINNGG -- Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also
describe potential serious adverse reactions and safety hazards.
CCAAUUTTIIOONN -- Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury to the user or patient or damage to the product or other property. This includes special care necessary for the safe
and effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use or
misuse.
NNoottee -- Provides special information to make maintenance easier or important instructions clearer.
EN 2 6392-009-002 Rev E.4

SSuummmmaarryy ooff ssaaffeettyy pprreeccaauuttiioonnss
Always read and strictly follow the warnings and cautions listed on this page. Service only by qualified personnel.
WWAARRNNIINNGG
• Always use any appropriate personal protective equipment while power washing to avoid inhaling contagion. Power
washing equipment may aerate contamination.
CCAAUUTTIIOONN
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in this
manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable operation
resulting in injury to patient or operator. Modifying the product also voids its warranty.
• The use of accessories and cables, other than those specified, with the exception of cables that are sold by Stryker as
replacement parts for internal components, may result in increased emissions or decreased immunity of the
PPeerrffoorrmmaannccee--LLOOAADD system.
• Do not use the PPeerrffoorrmmaannccee--LLOOAADD system and the PPoowweerr--PPRROO cot adjacent to or stacked with other equipment. If
adjacent or stacked use is necessary, observe the PPeerrffoorrmmaannccee--LLOOAADD system to confirm normal operation in the
configuration where it will be used.
• Do not use portable RF communications equipment (including peripherals such as antenna cables and external
antennas) no closer than 30 cm (12 in.) to any part of the PPeerrffoorrmmaannccee--LLOOAADD system, including cables specified by
the manufacturer. Otherwise, degradation of the performance of this equipment could result.
• The emissions characteristics of this equipment make it suitable for use in industrial areas and hospitals (CISPR 11
class A). This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area (for which CISPR 11 class B is normally required) is likely to cause harmful interference
in which case the user will be required to correct the interference at their expense. In the event of interference, please
relocate or reorient the PPeerrffoorrmmaannccee--LLOOAADD system or interfering product.
• Do not clean, service, or perform maintenance while the product is in use.
• Do not clean, disinfect, service, or perform maintenance while the product is in use.
• Always wipe with clean water and dry each product after disinfecting. Some disinfectants are corrosive in nature and
may cause damage to the product. If you do not rinse and dry the product, you may leave a corrosive residue on the
surface of the product. This corrosive residue could cause premature degradation of critical components. Failure to
follow these disinfecting instructions may void your warranty.
6392-009-002 Rev E.4 3 EN

IInnttrroodduuccttiioonn
This manual assists you with the operation or maintenance of your Stryker product. Read this manual before operating or
maintaining this product. Set methods and procedures to educate and train your staff on the safe operation or maintenance
of this product.
CCAAUUTTIIOONN
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in this
manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable operation
resulting in injury to patient or operator. Modifying the product also voids its warranty.
NNoottee
• This manual is a permanent part of the product and should remain with the product even if the product is sold.
• Stryker continually seeks advancements in product design and quality. This manual contains the most current product
information available at the time of printing. There may be minor discrepancies between your product and this manual. If
you have any questions, contact Stryker Customer Service or Technical Support at 1-800-327-0770.
PPrroodduucctt ddeessccrriippttiioonn
PPeerrffoorrmmaannccee--LLOOAADD is a manual cot fastener designed to secure compatible ambulance cots into a ground-based
transport vehicle for patient transportation purposes and to allow for the insertion and removal of the compatible ambulance
cots.
When the compatible cot is secured in the transport position, PPeerrffoorrmmaannccee--LLOOAADD can inductively charge compatible
model ambulance cots with an inductive charging option. In the event of loss of charging, PPeerrffoorrmmaannccee--LLOOAADD remains
functional for guiding into, securing within, and removing the cot from the vehicle.
IInnddiiccaattiioonnss ffoorr uussee
PPeerrffoorrmmaannccee--LLOOAADD is intended to guide the loading and unloading of a compatible ambulance cot (wheeled stretcher) to
and from a ground-based transport vehicle and to secure the ambulance cot during transport in a fastened position while
also providing an optional inductive charging platform for charge-compatible ambulance cots.
EExxppeecctteedd sseerrvviiccee lliiffee
The PPeerrffoorrmmaannccee--LLOOAADD cot fastener has a seven year expected service life under normal use conditions and with
appropriate periodic maintenance.
CCoonnttrraaiinnddiiccaattiioonnss
None known.
SSppeecciiffiiccaattiioonnss
Length 70 in. 178 cm
Width 19 in. 48 cm
Height 6 in. 15 cm
Floor plate assembly weight 16.5 lb 7.5 kg
EN 4 6392-009-002 Rev E.4

Fastener assembly weight 46 lb 21 kg
Minimum operators required for loading/unloading an occupied
cot
2
Minimum operators required for loading/unloading an
unoccupied cot
1
Recommended loading height 22 in. to 36 in. 56 cm to 91 cm
Electrical requirements - inductive charging (optional) 12.8 VDC-15.6 VDC, 15A fuse/breaker, 2 conductor 10
AWG cable
Standards KKK-A-1822F
With inductive charging: IEC 60601-1 Edition 3.0, IEC
60601-1 Edition 3.1, IEC 60601-1-2 Edition 3.0, IEC
60601-1-2 Edition 4.0, IEC 60601-1-12 Edition 1.0,
ANSI/AAMI ES60601-1: 2005/(R)2012, CSA-C22.2 No.
60601-1 (2014)
For standards that require specific options, see
Standards with required options (page 5).
Stryker reserves the right to change specifications without notice. Patents pending.
The yellow and black color scheme is a proprietary trademark of Stryker Corporation.
EEnnvviirroonnmmeennttaall ccoonnddiittiioonnss OOppeerraattiioonn SSttoorraaggee aanndd ttrraannssppoorrttaattiioonn
Temperature
130 °F
(54 °C)
-30 °F
(-34 °C)
158 °F
(70 °C)
-40 °F
(-40 °C)
Relative humidity
93%
0%
93%
0%
Atmospheric pressure
1060 hPa
620
1060 hPa
620
CCAAUUTTIIOONN
• The use of accessories and cables, other than those specified, with the exception of cables that are sold by Stryker as
replacement parts for internal components, may result in increased emissions or decreased immunity of the
PPeerrffoorrmmaannccee--LLOOAADD system.
• Do not use the PPeerrffoorrmmaannccee--LLOOAADD system and the PPoowweerr--PPRROO cot adjacent to or stacked with other equipment. If
adjacent or stacked use is necessary, observe the PPeerrffoorrmmaannccee--LLOOAADD system to confirm normal operation in the
configuration where it will be used.
• Do not use portable RF communications equipment (including peripherals such as antenna cables and external
antennas) no closer than 30 cm (12 in.) to any part of the PPeerrffoorrmmaannccee--LLOOAADD system, including cables specified by
the manufacturer. Otherwise, degradation of the performance of this equipment could result.
• The emissions characteristics of this equipment make it suitable for use in industrial areas and hospitals (CISPR 11
class A). This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area (for which CISPR 11 class B is normally required) is likely to cause harmful interference
in which case the user will be required to correct the interference at their expense. In the event of interference, please
relocate or reorient the PPeerrffoorrmmaannccee--LLOOAADD system or interfering product.
SSttaannddaarrddss wwiitthh rreeqquuiirreedd ooppttiioonnss
To be compliant with the standards, you must use PPeerrffoorrmmaannccee--LLOOAADD with the following compatible cots. See the
Operations Manual for your cot model for more information.
6392-009-002 Rev E.4 5 EN

NNoottee -- Compatible cot is loaded into PPeerrffoorrmmaannccee--LLOOAADD in powered mode for crash testing.
SSttaannddaarrdd PPeerrffoorrmmaannccee--LLOOAADD ccoommppaattiibbllee ccoott mmooddeellss
SAE J3027 6506, 6086
BS EN 1789:2007 +A2:2014 and AS/NZS-4535:1999
applicable clauses
6506
PPrroodduucctt iilllluussttrraattiioonn
A
B
C
H
D
G
E
F
A Foot end E Foot end interface
BFloor plate F Cot fastener
CSafety hook G Head end interface
D Release button H Head end
IImmppoorrttaanntt ccoonnttaacctt iinnffoorrmmaattiioonn
For information about Federal Ambulance Specification KKK-A-1822F, contact:
Chief, Automotive & Commodity Management Branch (QMDAA)
Office of Motor Vehicle Management
General Services Administration
R2200 Crystal Drive, Suite 1006
Arlington, VA 22202 USA
Telephone: [phone]
EN 6 6392-009-002 Rev E.4

For more information about AMD standards, contact:
Ambulance Manufacturers Division
(National Truck Equipment Association)
37400 Hills Tech Drive
Farmington Hills, MI 48331-3414 USA
CCoonnttaacctt iinnffoorrmmaattiioonn
Contact Stryker Customer Service or Technical Support at: 1-800-327-0770.
Stryker Medical
3800 E. Centre Avenue
Portage, MI 49002
USA
To view your operations or maintenance manual online, see https://techweb.stryker.com/.
Have the serial number (A) of your Stryker product available when calling Stryker Customer Service or Technical Support.
Include the serial number in all written communication.
SSeerriiaall nnuummbbeerr llooccaattiioonn
A
FFiigguurree 11 –– SSeerriiaall nnuummbbeerr llooccaattiioonn
DDaattee ooff mmaannuuffaaccttuurree
The year of manufacture is the first four digits of the serial number.
6392-009-002 Rev E.4 7 EN

CClleeaanniinngg aanndd ddiissiinnffeeccttiinngg wwiitthh wwiippeess
For United States only. Confirm availability for your configuration or region. Call Stryker Customer Service: 1-800-327-
0770.
Stryker’s preferred wipes (2060-000-001 6'' x 10'' or 2060-000-002 9'' x 12'') include the following active ingredients:
• n-Alkyl (60% C14, 30% C16, 5% C12, 5% C18) dimethyl benzyl ammonium chloride - 0.154%
• n-Alkyl (68% C12, 32% C14) dimethyl ethylbenzyl ammonium chloride - 0.154%
• Isopropanol - 21.000%
Non-active ingredient: Ethylene Glycol Monobutyl Ether – < 3%
NNoottee -- For safety information, read the product label.
To clean or disinfect the external product surface:
1. To clean, wipe external surfaces with a fresh, clean wipe to remove all visible soils. Repeat as necessary until the
product is clean.
NNoottee
• Use as many wipes as necessary.
• Complete step 1 before you disinfect.
2. To disinfect, wipe external surfaces with a fresh, clean wipe until wet. Allow the external surface to remain wet for two
minutes at room temperature.
3. Allow the product to dry before you return it to service.
EN 8 6392-009-002 Rev E.4

CClleeaanniinngg
WWAARRNNIINNGG -- Always use any appropriate personal protective equipment while power washing to avoid inhaling contagion.
Power washing equipment may aerate contamination.
CCAAUUTTIIOONN -- Do not clean, service, or perform maintenance while the product is in use.
The product is power washable. The product may show some signs of oxidation or discoloration from continuous washing.
No degradation of the product’s performance will occur from power washing as long as you follow the proper procedures.
• Follow the cleaning solution manufacturer’s dilution recommendations exactly.
• Power wash with recommended cleaners. Hose down the product and towel dry the guide.
• Power wash the rails and interface plates with a hand held wand unit or wipe the product with a clean cloth and
recommended cleaners.
NNoottee -- Water that gets into the PPeerrffoorrmmaannccee--LLOOAADD system will drain through the drain tube to the underside of the
vehicle.
DDiissiinnffeeccttiinngg
CCAAUUTTIIOONN
• Do not clean, disinfect, service, or perform maintenance while the product is in use.
• Always wipe with clean water and dry each product after disinfecting. Some disinfectants are corrosive in nature and
may cause damage to the product. If you do not rinse and dry the product, you may leave a corrosive residue on the
surface of the product. This corrosive residue could cause premature degradation of critical components. Failure to
follow these disinfecting instructions may void your warranty.
In general, when used in concentrations recommended by the manufacturer, you can use either phenolic or quaternary
(excluding VViirreexx® TB) type disinfectants. Iodophor type disinfectants are not recommended for use because staining may
occur.
The recommended disinfectants for this product’s surfaces include the following:
• Quaternary (active ingredient - ammonium chloride) that contain less than 3% glycol ether
• Phenolic (active ingredient - o-phenylphenol)
• Chlorinated bleach solution (use up to UK disinfecting 10,000 ppm available chlorine (941 mL of a 5.25% sodium
hypochlorite solution per 4000 mL of water)
• Alcohol (active ingredient - 70% isopropyl alcohol)
To wipe down the product with disinfectant between uses:
1. Follow the manufacturer’s dilution recommendations exactly.
2. Apply the recommended disinfectant solution by spray or pre-soaked wipes.
3. Hand wash all surfaces of the product with the recommended disinfectant.
4. Disinfect all exposed surfaces. Pay attention to high contact areas.
5. Follow the disinfecting solution manufacturer’s instructions for appropriate contact time and rinsing requirements.
6. Dry the product thoroughly before returning the product to service.
Avoid over saturation. Do not allow the product to remain wet.
Follow the manufacturer’s dilution recommendations for appropriate contact time and rinsing requirements. Follow the
chemical manufacturer’s guidelines for proper disinfecting.
6392-009-002 Rev E.4 9 EN

PPrreevveennttiivvee mmaaiinntteennaannccee
Establish and follow a maintenance schedule and keep records of the maintenance activity. Remove product from service
before you perform the preventive maintenance inspection. You may need to perform preventive maintenance checks more
often based on your level of product usage. Service only by qualified personnel.
EEvveerryy mmoonntthh
CChheecckk RRoouuttiinnee
Foot end interface and head end interface Clean debris
EEvveerryy tthhrreeee mmoonntthhss
CChheecckk RRoouuttiinnee
Loose fasteners Replace if loose
EEvveerryy ttwweellvvee mmoonntthhss
CChheecckk RRoouuttiinnee
All parts Replace any worn parts, including covers, cot guides, and
latch assembly, if necessary
Full functionality See the Installation checklist in the Operations Manual
MMaaiinntteennaannccee rreeccoorrdd
DDaattee MMaaiinntteennaannccee ooppeerraattiioonn
ppeerrffoorrmmeedd
BByy HHoouurrss
EN 10 6392-009-002 Rev E.4

DDaattee MMaaiinntteennaannccee ooppeerraattiioonn
ppeerrffoorrmmeedd
BByy HHoouurrss
TTrraaiinniinngg rreeccoorrdd
TTrraaiinniinngg ddaattee
TTrraaiinneeee nnaammee BBaassiicc ttrraaiinniinngg RReeffrreesshheerr uuppddaattee OOwwnneerr’’ss mmaannuuaall,, iinn--
sseerrvviiccee,, ffoorrmmaall ccllaassss,, eettcc..
6392-009-002 Rev E.4 11 EN

TTrraaiinniinngg ddaattee
TTrraaiinneeee nnaammee BBaassiicc ttrraaiinniinngg RReeffrreesshheerr uuppddaattee OOwwnneerr’’ss mmaannuuaall,, iinn--
sseerrvviiccee,, ffoorrmmaall ccllaassss,, eettcc..
EN 12 6392-009-002 Rev E.4

TTrroouubblleesshhoooottiinngg
IInndduuccttiivvee cchhaarrggiinngg ssyysstteemm ddooeess nnoott cchhaarrggee tthhee ccoott bbaatttteerryy
Inductive charging system does not charge the cot battery when you load the cot into the fastener.
NNoottee -- Before you service the cot, disconnect the vehicle’s battery starting with the negative lead.
1. Make sure that a SSMMRRTT Pak battery is used on the cot and that the cot is equipped with inductive charging hardware.
2. Verify proper connection between the anchor-to-vehicle cable and the inductive primary board.
a. Check for 12.8V to 15.6V at the PPeerrffoorrmmaannccee--LLOOAADD end of the anchor-to-vehicle cable (6390-001-135)
connection.
b. If present, continue to step 3.
c. If not present, make sure that the vehicle meets the following electrical requirements: 12.8V - 15.6V, 15A fuse/
breaker and two conductor 10 AWG cable.
3. Reattach the anchor-to-vehicle cable to the mating side of the inductive primary board.
NNoottee -- Make sure that like-colored wires are connected (red to red; black to black).
4. After making the connection, verify proper functionality as follows:
a. Load a PPoowweerr--PPRROO cot (with a SSMMRRTT Pak battery) into the fastener, make sure that the PPoowweerr--PPRROO battery
indicator is OFF prior to loading the cot into PPeerrffoorrmmaannccee--LLOOAADD.
b. If the unit is functioning properly, the cot light panel orb will turn on within five seconds of being loaded into
PPeerrffoorrmmaannccee--LLOOAADD. The light indicates that the unit is receiving power and that the electrical installation is correct
and complete.
c. If the light panel orb does not turn ON, check all connection points and replace the inductive coil and/or the primary
board.
6392-009-002 Rev E.4 13 EN

SSeerrvviiccee
HHeeaadd eenndd iinntteerrffaaccee aasssseemmbbllyy rreeppllaacceemmeenntt
TToooollss RReeqquuiirreedd::
• T27 Torx driver
• 1/4'' hex wrench
• Torque wrench (in-lb)
PPrroocceedduurree::
1. Using a T27 Torx driver, remove and save the four screws that secure the head end top cover to the head end bottom
covers.
2. Using a ¼'' hex wrench, remove and save the four screws (A) that secure the head end interface assembly (P) to the
head end weldment (T) (Figure 2).
NNoottee -- Torque item (A) to 300 in-lb.
3. Remove and discard the head end interface assembly.
4. Reverse steps to reinstall.
5. Verify proper operation before returning the product to service.
Torque item A
to 300 ± 15 in-lb
FFiigguurree 22 –– RReeppllaacciinngg tthhee hheeaadd eenndd iinntteerrffaaccee aasssseemmbbllyy
FFoooott eenndd iinntteerrffaaccee aasssseemmbbllyy rreeppllaacceemmeenntt
TToooollss rreeqquuiirreedd::
• T27 Torx driver
• 1/4'' hex wrench
• Torque wrench (in-lb)
PPrroocceedduurree::
1. Using a T27 Torx Driver, remove and save the six screws that secure the foot end top cover to the foot end bottom
cover.
EN 14 6392-009-002 Rev E.4

2. Using a ¼'' hex wrench, remove and save the six screws (A) that secure the foot end interface assembly (K) to the foot
end weldment (R) (Figure 3).
NNoottee -- Torque item (A) to 300 in-lb.
3. Remove the foot end interface from the lower release link by sliding it toward the head end.
4. Reverse steps to reinstall.
5. Verify proper operation before returning the product to service.
Torque item A
to 300 ± 15 in-lb
FFiigguurree 33 –– RReeppllaacciinngg tthhee ffoooott eenndd iinntteerrffaaccee aasssseemmbbllyy
IInndduuccttiivvee pprriimmaarryy bbooaarrdd rreeppllaacceemmeenntt ((ooppttiioonnaall))
TToooollss RReeqquuiirreedd::
• T27 Torx driver
PPrroocceedduurree::
1. Unsnap the floor plate cover to gain access to the electrical connection.
2. Disconnect the red and black wires from the cable harness.
3. Using a T27 Torx driver, remove and save the six screws that secure the foot end top cover to the foot end bottom
cover.
4. Using a T27 Torx driver, remove the two screws (A) that secure the inductive charging assembly (C) to the foot end
weldment (Figure 4).
5. Remove the inductive charging assembly.
6. Remove the inductive primary board from the charging enclosure. Discard the inductive primary board.
NNoottee -- Do not dispose of as unsorted municipal waste. Refer to your local distributor for return or collection systems
available in your country.
7. Reverse steps to reinstall.
8. Verify proper operation before returning the product to service.
6392-009-002 Rev E.4 15 EN

FFiigguurree 44 –– RReeppllaacciinngg tthhee iinndduuccttiivvee pprriimmaarryy bbooaarrdd
HHeeaadd eenndd pplluunnggeerr rreeppllaacceemmeenntt
TToooollss RReeqquuiirreedd::
• T27 Torx driver
PPrroocceedduurree::
1. Remove the head end interface assembly. (See
Head end interface assembly replacement (page 14)).
2. Using a T27 Torx driver, remove and save the four screws (A) that secure the pin enclosure (C) to the head end
interface (B) (Figure 5).
3. Remove and save the two plunger springs (D) (Figure 5).
4. Remove and save the plunger bracket (F) (Figure 5).
5. Remove and discard the plunger (E) (Figure 5).
6. Reverse steps to reinstall.
7. Verify proper operation before returning the product to service.
EN 16 6392-009-002 Rev E.4