Stryker Physio Control Lifepak CR2 User manual

Wireless Setup
Guide
LIFEPAK® CR2 Defibrillator
with LIFELINKcentral™AED Program Manager
2

Please ensure the LIFEPAK CR2 Defibrillator is ‘Connected and Ready’ for use in an emergency by
following these simple instructions.
Before You Begin
Determine your debrillator type
Follow the Getting Started Guide provided with the
defibrillator and determine what type of defibrillator you
have:
USB only
Wi-Fi®and USB
Wi-Fi, cellular, and USB
If the defibrillator is USB only, do not attempt this
procedure.
Note: In this guide, the term “AED” (Automated External
Defibrillator) is used to refer to the defibrillator.
Determine your online account type
You should have an account on one of the following
two websites.
LIFELINKcentral AED Program Manager, or
LIFENET®System
Many health care organizations have existing LIFENET
System accounts to manage their devices. If your
organization has a LIFENET System account, do not
use this setup guide. Instead, log in to your account
and download the Wireless Setup Guide for
LIFEPAK CR2 defibrillators from the Resource Center.
If you do not have a LIFENET System account, follow
this setup guide and use LIFELINKcentral AED Program
Manager to set up your AED.

Wireless Setup Overview
A typical wireless setup takes 10-20 minutes.
The following pages will guide you through these steps:
Download a software application from a website to your
computer.
Run the application on your computer to load Wi-Fi
network settings into the AED.
Connect the AED to the wireless network at its intended
location.
Confirm the AED status in your online account.
Note: Physio-Control recommends that all LIFEPAK CR2 AEDs
with Wi-Fi capability be set up with a Wi-Fi network, even if the
AED also has cellular capability.

Pre-installation Checklist
a. Set up your LIFEPAK CR2 Defibrillator (AED) as
instructed in the Getting Started Guide and verify the
Readiness indicator is flashing.
b. Confirm that the intended location for the AED has a
good connection to the Wi-Fi network.
Test the signal strength of the Wi-Fi network at the
intended AED location using a different Wi-Fi device
such as a smartphone.
c. Identify the Wi-Fi network information you will need to
connect the AED to the network.
NETWORK NAME:
SECURITY KEY:
d. Confirm that you have a PC with internet access and
Windows®7 or above operating system. You will need
Administrator rights on the PC.
e. Locate the USB cable included in the shipping box.
FAQs
Q: I need to set up multiple AEDs at locations that have dierent Wi-Fi networks. What should I do?
A: In step c above, identify the network information for each Wi-Fi network.
Q: I want to skip the Wi-Fi setup and only test the cellular connection. How do I do that?
A: Skip steps b through e above, and begin this procedure at step 4.

1Log in to your LIFELINKcentral AED Program Manager account.
Use the logon name and password from your
“Welcome to LIFELINKcentral” email to log in.
FAQs
Q: I did not receive an email with my logon name and password. What should I do?
A: Check to see if the email was sent to another person in your organization. If you cannot find the email,
look up the appropriate web address for your country in the contact list included with this guide. Go to
the website to create your account.

2a. Select Resource Center and then select
Wi-Fi Configuration Tool.
Download and install the Wi-Fi Conguration Tool to your PC.
b. Click the icon in the upper right corner
of the screen to download the Wi-Fi
Configuration Tool.

FAQs
Q: My computer rebooted during the installation process. Is this okay?
A: Yes. If your computer reboots, installation should continue automatically.
d. When you see the InstallShield Wizard
Completed screen, make sure the Launch
Wi-Fi Configuration Tool checkbox is selected,
and then click Finish.
c. After the Wi-Fi Configuration Tool
has downloaded, double-click the
WCT.xxxxx_Setup.exe file to install it.
If you don’t see the file, look in your
Downloads folder.
If any security warnings appear, select the
option to allow the file.
The InstallShield Wizard will appear.
Select your language and click Next>.

b. When you are instructed to Connect LIFEPAK CR2
to Computer, use the USB cable included in the
shipping box.
c. Continue to follow all onscreen instructions and
click Next.
3a. In the Registration screen, select your
country and enter your user name and
password. This is the same logon name
and password you use to log in to
LIFELINKcentral AED Program Manager.
Run the Wi-Fi Conguration Tool and follow the onscreen instructions.
This step loads your Wi-Fi network settings into the AED.

e. When the Wi-Fi setup is complete, you will
see the Update Successful screen.
f. Click Next, disconnect the USB cable, and
then click Close.
d. In the Specify Wi-Fi Network Settings screen,
select a network or click Add Custom Network
to enter your Wi-Fi network settings. Click Next
to apply the settings.
FAQs
Q: I closed the Wi-Fi Configuration Tool and need to open it again. Where can I find it?
A: Open the Start menu on your computer, and open the Physio-Control folder. Click
Wi-Fi Configuration Tool.

4a. Take the AED to its intended location.
b. Open the lid and wait until the voice
prompts start.
c. Immediately press and hold the
LANGUAGE and CHILD MODE buttons
simultaneously until you hear “Device
ready.”
d. Immediately:
Close the lid
Place the AED in its permanent storage location
(for example, cabinet or vehicle)
Close the door of the cabinet or vehicle
The AED will attempt a wireless connection and it must
be in its permanent location during this test.
Take the AED to its intended location and test the wireless connection.