Sub-Zero Designer Series User manual

Designer Series
Undercounter Wine Storage
Installation Guide
Guía de instalación
Guide d’installation
Guida all’installazione
Installationsanleitung
Installatiehandleiding
安装指南

2 | English
Important Note
To ensure this product is installed and operated as safely
and eciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or prod-
uct damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Designer Series Undercounter Wine Storage
Product Information
Important product information, including the model and
serial number, are listed on the product rating plate. The
rating plate is located on the underside of the control
panel, on the left. Refer to the illustration below.
If service is necessary, contact your authorized Sub-Zero
dealer.
Contents
2Designer Series Undercounter Wine Storage
3Opening Dimensions
3Electrical Requirements
4Preparation
4Anti-Tip Bracket
490° Door Stop
4Placement
5Alignment
5Door Panel
6Panel Installation
7Completion
RATING PLATE
Rating plate location

subzero.com | 3
Site Preparation
The depth of each model is 587 mm. Allow for panel thick-
ness when planning the finished opening depth. A mini-
mum 89 mm finished return is required on all sides of the
opening. Framed cabinets require additional finished filler
material behind the face frame for a proper installation.
Refer to the illustration.
DUAL INSTALLATION
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 51 mm filler strip is recommended between
the units. Dual installations without a filler strip can only be
accomplished using two units with opposite hinges. Refer
to the illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer.
DUAL OPENING WIDTH W
Two 610 mm Models 1219 mm
Dual installation kit required.
Opening Dimensions
DESIGNER SERIES UNDERCOUNTER WINE MODELS
Electrical Requirements
Installation must comply with all applicable electrical
codes and be properly grounded (earthed).
The electrical supply must not be behind the appliance but in
accessible cabinets either side.
The electrical outlet must be positioned with the ground-
ing prong to the right of the thinner blades.
ELECTRICAL REQUIREMENTS
Electrical Supply 220-240 V AC, 50/60 Hz
Service 10 amp
Receptacle grounding-type (earthed)
W
OPENING WIDTH
H
OPENING
HEIGHT
TOP VIEW
SIDE VIEW FRONT VIEW
NOTE: 89 mm finished returns will be visible and should be finished to match cabinetry.
19 mm
TYPICAL
FRAMED
CABINETRY
W
FILLER
89 mm
FINISHED
RETURN
FRAMELESS
CABINETRY
W
19 mm
TYPICAL
89 mm
FINISHED
RETURN
620mm
OPENING
DEPTH
WITHOUT FILLER STRIP FILLER STRIP
Opposite hinges Same side hinges
OPENING DIMENSIONS W H
610 mm Model 610 mm 876 mm
CAUTION
The outlet must be checked by a qualified electrician
to be sure it is wired with the correct polarity. Verify
the outlet is properly grounded (earthed).
WARNING
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly quali-
fied persons in order to avoid a hazard.
WARNING
Do not locate multiple portable socket-outlets,
power strip, or portable power supplies at the rear of
the appliance.
WARNING
Do not use an extension cord, two-prong adapter, or
remove the power cord ground prong.
Electrical
Shock
Hazard
Plug power cord directly into a properly
grounded (earthed) outlet.
Do not defeat the grounding (earthing)
nature of the plug.
Do not use adapter or extension cord.
Failure to follow these instructions could
cause serious injury or death.
See installation instructions

4 | English
Site Preparation
Preparation
Uncrate the unit and inspect for damage. Remove and
recycle packing materials. Do not discard the kickplate,
anti-tip bracket, and hardware.
Remove the kickplate by extracting the two mounting
screws. Refer to the illustration below.
SCREW
Kickplate removal
90° Door Stop
The door stop pins provided with the unit limit the door
swing to 90°.
IMPORTANT NOTE: If a 90° door opening is desired, the
pins must be installed prior to installing the unit into the
opening.
To install, open the door to approximately 80°. Insert one
hinge pin into each hinge. Refer to the illustration below.
DOOR STOP PIN
90° door stop
Anti-Tip Bracket
WARNING
To prevent the unit from tipping forward, the anti-tip
bracket must be installed.
The anti-tip bracket should be attached to the wall behind
the unit with the bracket flange located 6 mm above the
top of the unit. Refer to the illustration below. Failure to
properly position the anti-tip bracket will prevent proper
engagement.
6 mm
ANTI-TIP
BRACKET
Anti-tip bracket
Placement
CAUTION
Before moving the unit into position, secure the door
closed and protect any finished flooring.
WARNING
When positioning the appliance, ensure the supply
cord is not trapped or damaged.
Use an appliance dolly to move the unit near the opening.
If the unit has been on its back or side, it must stand
upright for a minimum of 24 hours before connecting
power.
Plug the power cord into the grounded outlet and slide
the unit into position. Verify the anti-tip bracket is properly
engaged.

subzero.com | 5
ANCHORING
CAUTION
If using a power drill to predrill holes or install
screws, verify the drill chuck does not contact the
units face frame.
Adjust the depth of the unit to fit flush with the surround-
ing cabinetry. Allow for panel thickness. Once aligned,
verify the door opens properly, then install screws in each
bracket.
WARNING
To avoid a hazard due to instability of the appliance,
it must be fixed in accordance with the instructions.
Installation
Alignment
LEVELING
Once the unit is in position, rotate the front legs clockwise
to raise and counterclockwise to lower. Rear height adjust-
ment can be made from the front. Using a Phillips drive,
turn clockwise to raise the unit or counterclockwise to
lower. Use the lowest torque setting when using a power
drill. Do not turn the leveling legs by hand. Refer to the
illustration below.
When the unit is properly leveled, door adjustments are
less likely to be necessary.
IMPORTANT NOTE: Level the unit to the floor, not the
surrounding cabinetry. This could aect the operation of
the unit, such as door closing.
WARNING
To reduce the possibility of the unit tipping forward,
the front leveling legs must be in contact with the
floor.
REAR
ADJUSTMENT
FRONT
ADJUSTMENT
Leveling
Stainless Steel Panel
Stainless steel panels are available through an authorized
Sub-Zero dealer.
Minimum 3 mm reveals are required.
Door Panel
Custom Panel
A custom door panel and handle hardware must be
installed.
A 16 mm minimum to 19 mm maximum thick panel is
required. The panel cannot exceed the maximum panel
weight indicated in the chart below. The depth of each
model is 587 mm. Allow for panel thickness when planning
the finished opening depth.
Minimum 3 mm reveals are required.
PANEL WEIGHT MAX
610 mm Model 10 kg
Finish all sides of the custom panel. They will be visible
when the door is open.
A D-style handle is recommended. Locate the door handle
near the edge of the panel opposite the hinge and cen-
tered top to bottom. Stainless steel tubular and pro handles
are available through an authorized Sub-Zero dealer.
Anchoring

6 | English
Custom Panel
TOE KICK CLEARANCE
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below.
Door Panel
MAXIMUM DOOR OPENING
As the panel width and/or depth increases, so does the
potential for panel interference. Interference may be
minimized by using the 90° door stop.
10 mm
DOOR CLOSED
19 mm PANEL
3 mm REVEAL
ADJACENT
CABINETRY
DOOR
OPEN
90°
DOOR OPEN
MAXIMUM 115°
Maximum door opening (top view)
DOOR PANEL ADJUSTMENT
Close the door. Make any necessary adjustments to align
the panel and reveals.
For side-to-side adjustment, move the panel side to side,
then install and tighten all mounting screws.
For up-and-down and in-and-out adjustments, slightly
loosen the bracket screws. Depending on the level of
adjustment required, it may be helpful to loosen all of the
bracket screws which will allow for maximum adjustment.
Once the bracket screws are loosened, use a wrench to
rotate the cams to make adjustments. After the adjust-
ments have been made, tighten all bracket screws. Refer to
the illustrations below.
BRACKET
SCREWS
IN-AND-OUT
CAM
BRACKET
SCREWS
UP-AND-DOWN
CAM
In-and-out adjustment Up-and-down adjustment
Panel Installation
DOOR PANEL INSTALLATION
Typical panel dimensions are based on an 876 mm finished
height with 3 mm reveals. Placement of the template must
be adjusted for panels exceeding the typical dimensions.
Place the panel face down on a protected work surface.
Position the template flush with the top and sides of the
panel. Verify the correct side of the template is being used,
then mark and drill holes. Refer to the illustration below.
Use a Torx drive to partially insert a #8 x ⁄" screw into the
second hole from the top on each side of the panel. The
screws should be approximately 4 mm proud of the panel
and will support the weight of the panel during installation.
Align the support screws on the back of the panel with the
slotted holes on both door mounting brackets. Refer to
the illustration below. Opening the door slightly may help
with alignment. Once the panel is supported by the screws,
partially insert a #8 x ⁄" screw into the second hole from
the bottom on each side of the panel, but do not tighten.
CAUTION
As reveals between cabinetry and the unit decrease,
severe finger pinching can occur while the door is
closing.
TOP OF DOOR PANEL
TOP OF DOOR PANEL
LEFT SIDE DOOR PANEL
RIGHT SIDE DOOR PANEL
BACK OF PANEL
Door panel template Door panel mounting
Installation
DOOR
PANEL HINGE
587 mm
TO BACK OF UNIT
51 mm
TO
114 mm
FROM
FLOOR
89 mm
MAX DEPTH
29 mm
KICKPLATE
ADJUSTMENT
876 mm
TYPICAL
PRODUCT
HEIGHT
DECORATIVE KICKPLATE
CANNOT EXTEND
BEYOND THIS
POINT
86 mm*
DECORATIVE
KICKPLATE
HEIGHT
*Not included. Dimension will vary as the product height increases or decreases
from the typical product height.
Toe kick clearance (side view)

subzero.com | 7
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.
All other trademarks are property of their respective owners in the United States and other countries.
Installation
KICKPLATE INSTALLATION
The kickplate must be removable for service. The floor
cannot interfere with removal. Finger-tighten the adjust-
ment bracket nuts. Refer to the illustration below. Make
in-and-out adjustments, then wrench-tighten the bracket
nuts. Install the kickplate with the provided screws.
A decorative kickplate can be attached to the factory-
installed kickplate. The three rows of vented louvers
cannot be covered.
To install a decorative kickplate, remove the paper backing
from the magnets and attach the decorative kickplate to
the magnets. The magnets allow the decorative kickplate
to be removed if necessary.
Completion
DOOR TRIM INSTALLATION
After the door panel has been adjusted, install the deco-
rative side trim to the door. To install, start at the top
and align the trim with the front and rear flanges on the
bracket, then snap into place by pushing the trim toward
the back of the panel. Once the top is secure, continue the
installation downward until the remaining trim is com-
pletely secure. Refer to the illustration below.
SIDE TRIM INSTALLATION
Install the decorative trim strip to the handle side of the
unit. The side trim snaps over the brackets attached to the
handle side of the unit. Refer to the illustration below.
Door side trim Unit side trim
KICKPLAT E
ADJUSTMENT SCREW
MAGNET
Kickplate adjustment Kickplate installation
WARNING
Follow all city and state laws when storing, recycling,
or discarding unused refrigerators and freezers.

SUB-ZERO, INC. P.O. BOX 44848 MADISON, WI 53744 USA SUBZERO.COM 800.222.7820
9042183 REV-A 10/2020