SUGATSUNE LAMP HC-30 User manual

PARTS COMPOSITION
CUT OUT DRAWING FOR DOOR AND DOORJAMB
Thank you for using our product. Before installation, please read this manual thoroughly to ensure correct installation.
Please keep this manual at hand for future reference.
ABOUT THE PRODUCT
STAINLESS STEEL Sliding Door Latch,
HC-30、HC-30H(with indicator)、HC-30R(double-sided thumb turn type)Installation Instruction
Stainless steel latch for sliding door.
Can be unlocked from outside in case of emergency.
PRECAUTIONS FOR USE
Make sure to follow the designated dimensions, specifications, and horizontal/vertical
angles. Make sure that the cabinet and door are not warped, since it may cause failure.
Make sure to check the screws for slack at regular intervals (one month from first usage,
half a year, and then one time every year is recommended).
Prohibited
Warning
Caution Required
Meaning of symbols
Caution:If not followed, injury or damage may result.
Both left and right hand.
2 23 mm of spindle is assembled into the body.
3Process the parts according to the actual products. 1
Double-sided
thumb turn plate
HC-30R
Indicator
HC-30H only
Partition plate
HC-30 only
Countersunk head screw1
ThumbturnA
Spindle1
Latch body
Hook
Trigger
Strike
Strike box
Countersunk head
wood screw3.520
Door thickness Thread length Spindle Length 2Type
28 31 12 23 HC-30
HC-30H
HC-30R
32 36 17 27
37 40 22 32
41 44 25 35
HC-30R
Only
45 48 27 39
49 52 32 43
Parts to be chosen according to the door thickness 1
Align the vertical and horizontal centerlines for both mortises.
Doorjamb (for strike and strike box) Door (for latch body)
15
(16.5)
10.5 930
(3.6)3
53
(3)3
14.5
66 66
65
33
15 15
80
(95.5)3
66 80
(95.5)3
(16.5)
Centerline Centerline
Door thickness
Through hole, I38

INSTALLATION
OPERATION CHECK
EMERGENCY RELEASE (HC-30、HC-30H
Latch body
Tapping screw
3.520
󱫀Latch Body 󱫂Thumb Turn, Spindle
󱫄Exterior Plate 󱫆Strike, Strike Box
󱫀Thumb Turn

2
Thumb turn A
Thumb turn A
Spindle
Square hole
Square hole
Latch body
Inside the
sliding door
Thumb turn B
Thumb turn 
Sliding door
Trigger
Make sure the hook is retracted in the case lock.
If the hook protrudes, insert the spindle into the square
hole of latch body, turn the spindle to retract the hook
while pushing the trigger.
Mounting
screw
Blue
Spindle
Outside the
sliding door
Back side
Insert into
a square hole
Indicator
(surface)
Partition plate
Selection according to application
Strike box
Strike
Tapping screw
3.520
Doorjamb
Double-sided thumb turn type
❶
❷
LockedUnlocked
❸
With indicator
LockedUnlocked
Blue Red
Pushing
the trigger
❶
❷
Rotate the
thumb turn
Hook
comes
out
❸
Locked
Red
Insert coins etc.
❶
❷
Rotate by
90 degrees
Unlocked
Blue
Hook is
retracted
❸
SUGATSUNE KOGYO CO.,LTD
Tokyo, JAPAN
Phone: [phone] E-mail:[email protected]
SUGATSUNE KOGYO (UK) LTD
Reading, UK
Phone: [phone] E-mail:[email protected]
SUGATSUNE EUROPE GmbH
Dusseldorf, GERMANY
Phone: [phone] E-mail:[email protected]
SUGATSUNE SHANGHAI Co., LTD
Shanghai, CHINA
Phone: [phone] E-mail:[email protected]
Guangzhou, CHINA
Phone: [phone] E-mail:[email protected]
SUGATSUNE KOGYO INDIA PRIVATE LIMITED
Mumbai, INDIA
Phone: [phone] E-mail:[email protected]
SUGATSUNE AMERICA, INC
California, USA
Phone: [phone] E-mail:[email protected]
Chicago, USA
Phone: [phone] E-mail:[email protected].
SUGATSUNE CANADA, INC.
Phone: [phone] E-mail:[email protected]
2020.07 1417-1
Strike box