Sumake HPFH080H User manual

SUMAKE PNEUMATIC TOOLS
High Torque Oil Free Full-Auto Shut Off
Air Composite Screwdriver
Test result according to EN ISO 11148-6:2012
SUMAKE INDUSTRIAL CO., LTD
4F,NO.351,Yangguang St.,Neihu District TAIPEI, TAIWAN, ZIP:114-91
Noise : EN ISO 15744
MODEL
Vibration
EN ISO 28927-2 Sound pressure level
Safety Instructions
Warning
HPFH080H No Load : 1.0 m/s278. dB(A)
HPFH110 No Load : 1.1 m/s277.0 dB(A)
HPFH180 No Load : 1.2 m/s277.0 dB(A)
HPFH250 No Load: 0.9 m/s278.0 dB(A)
1- Read this manual and
understand all safety
instructions before operation
the tool.
2- Wear an approved
ear-protector and gloves while
operating tool.
HPFH080H(110)(180)(250)-S-1310B-MIF
* The uncertaint
y
in the sound levels is 3 dB

HPFH080H
HPFH080H-P-2102A-MI
HIGH TORQUE OIL FREE FULL-AUTO SHUT OFF AIR COMPOSITE SCREWDRIVER

HPFH080H
PARTS LIST
No. Parts No. Description Q'ty No. Parts No. Description Q'ty
1 5A6032 End Housing 1 35 2S2056 Air Inlet Bushing [NPT] 1
2 7Q2011 Valve O-Ring 1 35 2S2057 Air Inlet Bushing [PT] 1
2-1 6N5006 Spring 1 36 2S6103 Retainer 1
3 6S6105 Valve 1 37 7S2102 Ball 32
4 7S2108 Set Screw And Washer 1 38 3S5001 Pilot Pin 1
4-1 2U6001 Switch Bushing 1 39 3S5211 Rear Clutch 1
55L2003 Switch (Grey) 1 40 6N2006 C Ring 1
6 7S5001 Ball Bearing 1 41 3S5219 Center Clutch 1
8 1S6001 End Plate 1 42 7S2112 Ball 2
10 1P6005 Cylinder 1 43 3S7067 Anvil 1
12 1P6046 Oil-Free Blade 3 44 7S2105 Ball 2
13 1P3026 Front Plate 1 45 6N5110 Spring 1
13-1 6N2020 C Ring 1 45-1 6N5112 Spring 1
14 7S2002 Ball Bearing 1 46 3S2227 Slide Base 1
15 5S2389 Booster 1 47 3S5221 End Clutch 1
15-1 7S2150 Screw 4 48 7S2102 Ball 25
15-2 7S2113 Screw 4 49 3S5231 Ball Race 1
16 1S6041 7T Rotor 1 50 6N2006 C Ring 1
17 5S2048 Cover 1 51 6N5004 Torque Spring 1
18 1S6101 Internal Gear 1 52 2S5120 Washer 1
19 1P6123 15T Plant Gear 3 54 3A5202 Clutch Housing 1
20 1P6302 Gear Cage 1 54-1 3S2247-A Anvil Bushing 1
21 1S3053 Connect 1 55 6S2012 Needle Pin 3
22 1S6201 Aluminum Ring 1 57 3A6031 Torque Ring 1
25 5A6076 Center Housing 1 57-1 3S5101 Regulation Washer 1
26 7S6503 Ball Bearing 1 58 6N2131 Spring 1
27 2Q2003 O Ring 1 58-1 6N2011 C Ring 1
28 2P3040 Silencer 1 59 5S2009 Bit Slide Sleeve 1
29 2A6023 Exhaust Deflector 1 59-1 7S3107 Ball 1
30 7Q2006 O Ring 1 60 6N2003 Spring 1
31 6S2021 Valve Plate 1 60-1 2S2109 Washer 1
32 6S6010 Operating Rod 1 61 6N2001 C Ring 1
33 6N2104 Cone Spring 1 61-1 5A6167 Rear Houshing 1
34 2P3010 Silencer 1 63 5A6507 Torque Cover 1
34-1 2Q5001 O Ring 1 63-1 7Q6117 O Ring 1
34-2 7L0002 Washer 1 65 5N3002 Suspension Ring 1
HPFH080H-P-2102A-MI
HIGH TORQUE OIL FREE FULL-AUTO SHUT OFF AIR COMPOSITE SCREWDRIVER

ECDECLARATION OF CONFORMITY
We: SUMAKE INDUSTRIAL CO., LTD.
4F, No. 351, Yangguang St., Neihu District, Taipei City, Taiwan
declare in sole responsibility that the equipment
Equipment：HIGH TORQUE OIL FREE FULL-AUTO SHUT OFF
AIR COMPOSITE SCREWDRIVER
Model/ Serial No.：HPFH080H(110)(180)(250)
to which this declaration applies, complies with these normative documents:
Machinery Directive: 2006/42/EC
and conforms to the following EN standard,
EN ISO 12100: 2010
EN ISO 11148-6:2012
Name and Signature/Position Date and Place
2013/6/28
MikeSu–ManagingDirector Taipei, Taiwan
HPFH080H(110)(180)(250)-D-1309B-MIF

HPFH-SERIES AIR SCREWDRIVER OPERATION MANUAL
1
For safety use, Please Follow the instructions. The operation without your local regulations may cause serious injury. Read thoroughly
and understand this instruction manual and keep this within reach for future reference.
Specification List
Model
Speed
Weight
Length
Diameter
Noise
Air
Pressure
Min
Air
hose
Bore
Air
Consumption
Torque
Range
Standard
Deviation
Fastening Capacity
Machine
Screw
Tapping
Screw
r.p.m.
g
mm
mm
±2dBA
Kg/cm²
mm
m3/min
Kgf-cm
%
HPFH030
2200
520
208
34
74
6.0
5.0
0.28
5-30
±3
M2.8-M5.0
M2.2-M4.0
HPFH045
1600
520
208
34
74
6.0
5.0
0.28
5-45
±3
M2.8-M6.0
M2.2-M4.7
HPFH060
1000
520
208
34
74
6.0
5.0
0.28
8-60
±3
M3.3-M6.3
M2.7-M5.0
HPFH070
800
520
208
34
74
6.0
5.0
0.28
10-45
±3
M3.6-M6.0
M2.8-M4.7
HPFH080
550
520
208
34
74
6.0
5.0
0.3
10-80
±3
M3.6-M6.9
M2.8-M5.8
HPFH080H
2500
850
245
42
78
6.0
8.0
0.55
20-80
±3
M3.6-M6.9
M2.8-M5.8
HPFH110
1200
850
245
42
78
6.0
8.0
0.55
20-110
±3
M4.4-M7.8
M3.6-M6.1
HPFH180
650
850
245
42
78
6.0
8.0
0.55
50-180
±3
M6.0-M9.3
M4.7-M7.2
HPFH250
430
870
245
42
78
6.0
8.0
0.55
30-250
±3
M5.0-M10.0
M4.0-M8.0
HPWFH350
300
870
245
42
78
6.0
8.0
0.55
70-350
±3
M6.8-M11.7
M5.3-M9.5
HPWFH400
250
870
253
42
78
6.0
8.0
0.55
50-400
±3
M6.0-M11.8
M4.7-M9.7
* HP(W)FH oil free* This high torque type is our new release.
FUNCTION INSTRUCTION
1. Bit slide sleeve Pull-type design
Operator can change rapidly the bit by pulling the Bit slide sleeve and this Pull-type design also increase the
safety.
2. Torque cover
To prevent improper torque adjustment by operator, this up-to-the-date design fixes torque at same
standard. Further, for this special structure design, the torque cover is necessary for tool during operation.
Due to the safety consideration and to prevent the tool be broken by any impacting, please operate tool as
per this instruction manual and note it is prohibitive to operate tool without torque cover.
3. Valve reverse switch
With this friendly Valve reverse switch design, operator can change the motor rotation direction rapidly by
adjusting only the Valve reverse switch.
TOOL OPERATION
1 Check carefully first if the bit fixed in proper position with Pull-type Bit slide sleeve.
2 Confirm if the air hose or air pipe is clean and dry.
3 Make sure the air hose or air pipe is well connected with air screwdriver.
4 Torque Adjustment
Pull the Bit slide sleeve for inserting the bit or for rapidly bit changing. Due to the safety consideration,
please make sure the bit is well fixed on tool before operating.
Pull softly Pull till the tip Insert Bit Fix Bit Confirm Bit position
Bit slide sleeve
Bit Slide Sleeve
Exhaust Deflector
Valve Reverse
Rear Housing
Torque cover
Air Inlet Bushing
Hard composite rubber grip
HPFH-I-1812E-MI

HPFH-SERIES AIR SCREWDRIVER OPERATION MANUAL
2
5 Refer to the below drawing instruction: Release first the Torque cover for torque adjustment, then tighten
necessarily the torque cover before operating. For better Torque management, there are also color rings for
torque management.
1 2 3 4
Release Torque Cover Drop Torque cover out Tighten to the right: Loosen to the left:
increase torque. decrease torque
6 Press the tool for start rotating, release it to stop operating, due to the safety consideration, please hold
carefully the tool during the whole operating duration.
7 Push Valve reverse switch for instantly changing of air motor rotation direction. Please stop first the
operation then reverse patented both way valve switch to change the rotation direction.
8 Air motor will automatically stop when the load reaches at the pre-set torque.
Caution : Improper operation may damage the tool.
AIR SUPPLY
1 Air tools are adversely affected by moisture. Since air from compressor contains much moisture and dust, it
is desirable to provide a filter in the pipeline to remove such undesirable elements.Also take the drain out
from air tank every day.
2 When using brand-new air hose or air pipe, blow and clean the air hose or pipe inside before installation.
3 Keep air hose or air pipe inside clean to prevent airdrop problem caused by lots of drain and dust
accumulated, either to avoid possibly inside diameter smaller problem after long term usage.
4 When disconnect air hose from air tool during operation, do not drop air hose end to the floor as dust or
other element may get into air hose.
5 Use air regulator to keep stable air pressure at 6.0kgf-cm²( 80~90 psi) at the toll. It is important to get
proper air pressure at the toll.
6 With high quality Oil-free motor, any moisture or lubrication injection may damage the air screwdriver,
please keep tool dry and avoid oil based substances exposing to the products. For avoiding moisture
affection, usingAir Dryer is necessary in wet area or under moist weather.
TOOL ADVANTAGE
1 High quality Oil-free Motor
High quality Oil-free Motor is our new design used on high technologic tool. At the beginning operation, the
power of Oil-free motor keeps stable at it’s top capability without any oil injection, but the power of Current
motor decreases till it’s lowest capability after 32 hours operating unless oil adding. The high technologic
Oil-free motor increases 60% torque and keeps noise as standard 74/78dB which prevents operator and
environment from noise damaging and accords with industrial classified tool standard.
(Please refer to the below table about Oil-free and current motor.)

HPFH-SERIES AIR SCREWDRIVER OPERATION MANUAL
3
2 CPK value＞1.33
With 3rd generation patented cross-path MSC clutch and special mechanical structure, this air screwdriver
accords with ISO5393 B class CPK value Torque deviation request (CPK value＞1.33). This patented one
pulse clutch system has also the merits of low vibration(less than 2.5ms), low torque deviation(±3%) and
wide torque range.
3 Push-start system
Push-start system is more convenient and with low standard deviation character.
4 All new patented mechanical design and comfort grip material
This new patented mechanical design is 20% lighter than other brand. With the unity sharping composite
grip and best balance design made by thermoplastic elastomer, the H-series straight type tool possess
better lasting, wearing-resisting, comfortable grasp and anti-glossy features.
5 Torque fix management system
The outside torque adjustment design let user either adjust the torque rapidly or without using the torque
lock nut. To avoid the adjustment by operator, this up-to-the date torque cover design prevent user to
change the torque at will. Also, with long-resisting Steel Torque Cover as accessory gives user an easily
visible torque marking system at a glance for all the H-series straight type air tools.
6 Speediness
Operator can change rapidly the bit by pulling the bit head (refer to Tool Operation #4).
USING CAUTION
1 Please note improper operating may damage the tool.
2 Due to the safety consideration, please make sure tool is completely under control before and during
operation.
3 Changing the rotation direction at will without stopping first the operation may damage the motor or reduce
the usage term. Please note it is prohibited to change the rotation direction during operation, the proper
operating method is stop first the operation, then change the rotation direction by pushing the Valve reverse
switch.
4 The air screwdriver can be damaged by accidental falls or impacts. Due to the safety consideration, please
hold the tool carefully or use the hook to prevent the tool dropping down.
5 Any moisture or lubrication injection may damage the air screwdriver, please keep tool dry and avoid oil
based substances exposing to the products. For avoiding moisture affection, using Air Dryer is necessary in
wet area or under moist weather.