Suncast MHR300 User manual

2002 Suncast Corporation, Batavia, IL 0360822A
OWNER'S MANUAL
MHR300 Metal Hose Reel
TOOLS REQUIRED
• Flat head screw driver
• Adjustable wrench and! or pliers
NOTE: Do not completely tighten screws until the assembly is
complete. For easier assembly, we recommend that two people
assemble this product.
A CAUTION
• Always release water pressure by leaving the hose nozzle OPEN
when not in use.
• Be sure to have the water turned OFF and the nozzle OPEN before
removing reel from mounting and also when rewinding hose.
• Do not inflate tires more than 30 psi.
Betore you begin...
This product has been packaged to assure it arrives in the best possible condition. Please be careful not to scratch product when
unpacking.
Read instructions prior to assembly. This kit contains parts that can be damaged if incorrectly assembled.
Please follow instructions. Suncast is not responsible for replacing parts damaged due to incorrect assembly.
MHR300 Warranty
Suncast® Corporation, 701 North Kirk Road, Batavia, lllinois6OSl 0 (manufacturer) warrants to the original purchaser only that the
enclosed hose reel is free from material and workmanship defects under normal household use at date of purchase. Defective product
or part must be returned, freight prepaid, to Suncast Corp., 701 North Kirk Road, Batavia, IL 60510, Attention: Parts Department,
along with the proof of purchase. Upon receipt of the aforesaid, the defective product or part will be repaired or replaced at the option
of the manufacturer without charge to the original purchaser and returned to the customer freight collect.
This limited warranty does not apply to damage resulting from accident, neglect, misuse, commercial use, alteration, operation not in
accordance with instruction, or repairs made or attempted by unauthorized persons.
This limited warranty applies only to the hose reel enclosed and does not apply to accessory parts.
THE MANUFACTURER'S LIABILITY HEREUNDER IS LIMITED SOLELYTO THE REPAIR OR REPLACEMENT OFTHE DEFEC-
TIVE PRODUCT OR PART AND THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSE-
QUENTIAL DAMAGES THAT MAY RESULT FROM ANY DEFECT IN MATERIAL OR WORKMANSHIP FROM THE BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or a limitation of how long an implied
warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may have other
rights, which may vary from state to state.

Assembly Instructions
Carefully remove all parts from the box and place on a smooth flat surface.
1.Remove the screw and washers from axle and insert axle (D) into axle brace
on frame (A) of unit. Make sure the flat on the axle is oriented correctly with
the flat in the axle hole.
2. Slide wheels (E) with wheel hub to the inside and the tire stem to the out-
side onto the extended poles of both axles. Secure wheels and large washers
with non-slip nut (H4) and tighten using enclosed wrench or adjustable
wrench.
3. Insert crank stem (F) into crank hub.
4. Place reel assembly (B) into reel frame (A) so that the reel assembly rests
inside the reel frame.
Crank Hub
Crank Stem
F
A

4. Insert reel assembly hub into crank stem and line up holes. Insert two car-
riage bolts (H3) from top and side of the crank hub and tighten using
enclosed wrench or adjustable wrench.
5. Assemble the coupling end of the reel frame by aligning the holes on the U
shaped bracket with the holes on the frame. Insert one 30mm screw per hole
and secure with one washer and one lock nut (H2). Tighten securely.
6. Slide the handle (C) on to the vertical posts located on the frame (A) and
align the holes. Secure the handle using 45mm screw, washer and nut (Hi).
7. Insert one rubber washer into female swivel coupling on the reel assembly
(B), then connect the male end of leader hose (G).
Attach garden hose to threaded water supply-tube and wind onto reel.
Hi
A

Please provide this information. Place of Purchase
Name
Street
State
Phone
MHR300
Ordering Instructions
1. Call Suncast for pricing information call 800-
846-2345 or 630-879-2050. Monday - Friday
8:00 am - 4:30 pm Central Time.
(Except holidays) Or see www.suncast.com
2. Completely fill out address. Print Clearly.
3. Add Shipping and Handling to Total Cost.
(Illinois residents add 6.75% sales tax.)
4. Send complete form with check or money
order to Suncast Corp.
5. No COD. Orders will be accepted.
Index No. Part Name Part No Cost Each OW. Ord. Total Cost
AFRAME
BREEL
CHANDLE
DAXLE (2)
E2 PLY PNEUMATIC TIRE (4)
F______________ CRANK
GLEADER HOSE
Hi 45MM SCREW AND NUT (2)
H2 30MM SCREW AND NUT (2)
H3 40MM CARRIAGE BOLT AND NUT (2)
H4 NON-SLIP NUT AND WASHER (4)
SUB TOTAL:
IL RESIDENTS ADD 6.75% TAX
SHIPPING & HANDLING
ENCLOSED MONEY ORDER ENCLOSED TOTAL:
Mail To: Suncast Corporation 701 NORTH KIRK ROAD • BATAVIA, IL, USA 60510
www.suncast.com
PATENTS
Patents pending. Made in China
CityZip Code
Date
F—
H3
D
For
information on
incast products and
replacement parts see
wwwsuncast corn