Sune Technology ALFAROMEO-IF User manual

•Specification
Compatibility : ALFAROMEO
Components : Interface* 1pcs
Interface Input/Output specification
Input : Analog RGB*1, A/V*2, CVBS(Rear Camera)*1
CVBS(Front Camera)*1
Output : To LCD*1
Power Spec
Input Power : 8VDC ~ 18VDC
Consumption : 5WATT
Switch input mode
- External video sources skip function : able to control input
videos on and off via DIP switches.
- Able to switch videos via the remote, button switch, and
original buttons.
- Able to detect the rear view camera (back up camera)
via CAN.
2
•Features
Control external videos sources (DVD, DTV) via Multi Media
Touch
Adjust external videos screen position
Check the improved Screen Display (User Friendly Interface)
Switch modes via original OEM button
Supply power to rear view camera (Back up camera)
Offer Dynamic Pas(Parking assistance system), moving
parking line based on the steering wheel movement.

3
•Product exterior
Length-97mm
Height-18mm
Width-160mm
•Components
AV * 1ea
(HAVCAB0056)
LCD * 1ea
(HLCDCA0049)
RGB * 1ea
(HRGBCA0013)
BUTTON * 1ea
(HARETC0001)
IR * 1ea
(HIRCAB0002)
Remote * 1ea
(REMOTE0001)
POWER * 1ea
(HPOWER0097)
MULTI * 1ea
(HARETC0240)
R-CAM * 1ea
(HARETC0002)

PIN Mode Dip S/W
1 RGB mode OFF : Display RGB(Navi) Mode
ON : Skip RGB(Navi) Mode
2 No use
3 AV1 mode OFF : Display AV1 Mode
ON : Skip AV1 Mode
4 AV2 mode OFF : Display A/V2 Mode
ON : Skip A/V2 Mode
5 Please refer to below Chart.
6
7 Rear Camera OFF : OEM rear camera
ON : Aftermarket rear camera
8 No use(OFF)
※ ON : DOWN / OFF : UP
4
•DIP SWITCH
※ If you set up Dip Switch No. 5 and 6 ON for 6.5 inch Stevio car and HU turns off,
please make dip switch No.5 ON and No.6 OFF.
※ Above Dip switch setting can be worked from FW v. 181214. (If below version,
please contact the distributor.)
※Please make sure to disconnect and reconnect the power cable after
changing the dip switch setting. Otherwise, new dip switch setting will not be
applied.
PIN DIP S/W Setting Dip S/W
5 OFF
8.8 inch
6 OFF
PIN DIP S/W Setting Dip S/W
5 ON
6.5 inch
6 OFF
PIN DIP S/W Setting Dip S/W
5 ON
6.5 inch (STEVIO)
6 ON

5
•Remote control
Key FUNCTION
POWER & PIP NO USE
MENU Activate Factory menu
OK Selection, changing image display
▲Up
▼Down
◀Left( Access the factory mode
if the button is pressed for 2 seconds)
▶Right (Activate factory reset
if the button is pressed for 2 seconds)

6
•Factory Setting
Adjust the position and size of image
<H-POSITION> <V-POSITION>
Setting for rear camera
H-POSITION : Move the image horizontally
V-POSITION : Move the image vertically.
IMAGE
PARK
UTIL1
UTIL2
INFO
PAS TYPE
PAS SETUP
REAR TYPE
SAFE ENABLE
Menu of FACTORY
MENU to Return SEL to Select/Save
PAS TYPE : Parking guideline setting
- NOT USED : No use parking guideline
- PAS ON : Selecting Dynamic parking guide line
- PAS OFF : Selecting fixed parking guide line
RAS SETUP : adjusting the position of the parking guideline
REAR TYPE : Choose rear camera recognition
* LAMP - Detecting the rear view camera via rear lamp (Installer must
connect “Rear-C” cable of the power cable to the rear lamp of the
car.)
*CAN - Detecting the rear view camera by CAN signal (Installer must
connect “CAN” cable of the power cable to the “CAN” cable of the
car.)
SAFE ENABLE : Able/unable to display the image of external modes
while driving(Default: Off)
IMAGE
PARK
UTIL1
UTIL2
INFO
H-POSITION
V-POSITION
Menu of FACTORY
MENU to Return SEL to Select/Save

7
•Factory Setting
NAVI MODEL : Select RGB Navigation model
(QROI)
AVOUT SELECT : Select background mode sound
via Car Aux(AV1, AV2, Default)
FACM FUNC : On - Use front camera
OFF –Skip Front camera
Select Navigation&Car model
Setting for other options
Able to check the version of product
IMAGE
PARK
UTIL1
UTIL2
INFO
NAVI MODEL
AVOUT SELECT
FCAM FUNC
Menu of FACTORY
MENU to Return SEL to Select/Save
IMAGE
PARK
UTIL1
UTIL2
INFO
FACTORY RESET
Menu of FACTORY
MENU to Return SEL to Select/Save
FACTORY RESET : FACTORY mode reset
IMAGE
PARK
UTIL1
UTIL2
INFO
SYSTEM VERSION
(MAIN -130723)
(TRIP -130723)
Menu of FACTORY
MENU to Return SEL to Select/Save

8
• OEM button
Press “MENU” button placed nearby the gear for a while
to switch the mode
(OEM → RGB → A/V1 → A/V2)

9
Supplied LCD Cable
•Installation Diagram
OEM LCD Cable
ACC
CAN2-L(OUT)
GND
CAN2-H(OUT)
CAN1-L(IN)
CAN1-H(IN)
B DATA (blue) SYNC GND
IR-DTV
NAVI-VIDEO SYNC
IR-NAVI
IR-DVD
R DATA (red) G DATA (green)
R
C
A
M
S
A
F
E
R
E
A
R
V
1
I
R
V
2
I
R
R
E
M
O
T
E
T
O
G
G
L
E
12
V
S
E
L
F
C
A
M
12
V
MULTI CABLE
A
U
D
I
O
(R)
O
U
T
A
U
D
I
O
(L)
O
U
T
F
C
A
M
A
U
D
I
O
(R)
IN
1
A
U
D
I
O
(L)
IN
1
R
C
A
M
V
I
D
E
O
IN
1
V
I
D
E
O
O
U
T
1
V
I
D
E
O
O
U
T
2
A
U
D
I
O
(R)
IN
2
A
U
D
I
O
(L)
IN
2
V
I
D
E
O
IN
2
A/V CABLE
Behind the headunit Behind the moniotor
RGB-INAVMULTIPWR/CAN

10
• LCD cable connection
Find OEM LCD cable
which is connected
between the monitor and
the headunit like picture
on the left
OEM LCD cable
Remove OEM lcd cable
from the monitor and
connect the supplied lcd
cable
Supplied LCD cable
OEM LCD cable
→ LVDS IN of the interface
Supplied LCD cable
→LVDS OUT of the interface

11
•CAN connection
1
2
Find the connector behind the headunit as shown above
Wire marked with ①shall be connected with
CAN1-L(IN) from the supplied power cable
Wire marked with ②shall be connected with
CAN1-H(IN) from the supplied power cable
The color of wires may vary depends on vehicles.
Make sure that cables are connected to the right pin position.

12
•Trouble shooting
Q. I cannot change mode
A. Check connection of Ground cable and IR Cable. Check LED lamp
is on, if not check connection of POWER cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V
sources connected are working well.
(Second lamp indicates AV sources connected works well.)
Check interface connection has been done well.
Q. Displayed image color is not proper (too dark or unsuitable color)
A. Press ▶button on the remote control for 2 seconds and check how
it goes, if it does not work, inform to manufacturer.
Q. I cannot watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
Q. Set mode not appear
A. Check DIP Switch.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps
on, inform to manufacturer.
Q. Screen only displays white color.
A. Check LCD out cable is connected well, if this status keeps, inform to
manufacturer.
Q. If no image is shown on screen after connecting CAN wire with Park
gear.
A. Go on the “FACTORY MODE”, check “UTIL-Rear Select”. If “LAMP”,
change the setting as “CAN” with the remote control. (※when
connecting Rear-C wire of LAMP power cable to Backup lights,
Setting should be like this / CAN : if controlling rear camera with
CAN wire)

Copyright ⓒ2019 by SUNE TECHNOLOGY
SUNE TECHNOLOGY CO.,LTD
No.9,Lane 606,Anping Rd,Tainan City 70849,TAIWAN TEL:[phone] FAX:
[phone]
Http://www.sune-tech.com
Shop http://www.carnavi-tech.com
SKYPE:sune_tech or hsin_han99