Sune Technology USM-BENZ9-NTG 4.5 User manual

USM-BENZ9-NTG 4.5 MANUAL
Installation Diagram : Use only the cable shown in the picture below.
OEM BUTTON USAGE
Update : 2018. 09. 19
DIP S/W SETTING
Q. What if the screen does not switch?
A. Make sure the first LED on the interface
turned on.
Q. What if the OEM screen does not
appear on the monitor?
A. Make sure that the cables on the back
of the monitor are well connected, and if
the problem persists, contact the
manufacturer for this problem.
-1/2-
1) JOG BUTTON (BACK)
- LONG PRESS : MODE SWITCH
- SHORT PRESS : BACK TO OEM
POWER/CAN
AV HD-IN 5CH
LVDS-IN
TO
TS-CON
TO
NAVI
5CH-OUT
USM BENZ9
NTG4.5
Remote Control setting
TS-OUT
TEST#1 TEST#2
DIP S/W
⑤OEM LVDS①POWER CAN ②Multi Cable ③HDMI input ④NAVI input
①②③④⑤
NAVI-IN
⑥LVDS output ⑦MNT-Interface Cable ⑧Touch cable :
CONNECT TO NAVI BOX
TOUCH PORT
⑨TS-Con : N/C ⑪DIP S/W
⑥⑦
⑧
⑫⑪⑩
TEST#35V-OUT
MNT-CON
⑬⑭
⑤Connect OEM LVDS cable that was connected to OEM monitor.
IMAGE
Product
Name
TEST :
USM-BENZ9-MAIN4.5-
V1.2
OEM W222 POWER CABLE(M) V2
QHI PGCTR AV CABLE(M) QNAVI4 RGB TOUCH CABLE USM BENZ9 MNT CABLE
Product
Code
QCPASS1291 HPOWER0207 HAVCAB0060 HTOUCH0022 HARETC0291
IMAGE
Product
Name
USM-BENZ9-MNT-V1.2 HDMI CABLE_SAMZHE_1M
REMOTE CONTROL
：
INTERFACE
Product
Code
QCPASS1292 HARETC0257 REMOTE0001
1
6
5
2
4
3
FAQ
⑨
2) HANDLE BUTTON (BACK)
- LONG PRESS : MODE SWITCH
- SHORT PRESS : BACK TO OEM
※FCAM setting could be found in
Factory Setting.
(Default is 3 seconds. If you don’t use,
please set OFF)
DIP1
OFF NAVI(LVDS) MODE
ON NAVI(LVDS) MODE SKIP
DIP2
OFF HDMI MODE
ON HDMI MODE SKIP
DIP3
OFF AV MODE
ON AV MODE SKIP
DIP4
OFF EXT FCAM
ON OEM FCAM
DIP5
OFF 800*480
ON 400 *240
DIP6
DIP7
OFF OEM RCAM
ON EXT RCAM
DIP8
N/C
3) HANDLE BUTTON (VOICE)
- RESET (PRESS 7Secs)
I/F Product size
W 140mm
H85mm
D21mm
Key Function
POWER/PIP N/C
MENU Activate OSD MENU
OK selection, mode switch
▲Moving upward
▼Moving downward
◀
Moving leftward (If press 2
seconds, could access the
factory mode)
▶
Moving rightward(If press 2
seconds, could reset all the
data about user environment)
Components

CAN & Power Connection
-2/2-
PAS TYPE: Select parking line type.
NOT USED: Do not use parking line
PAS ON: Use Flexible Parking Lines
PAS OFF: Use fixed parking line
PAS SETUP: You can move the position of parking line.
- H-POSITION: Moves the OSD screen left and right.
- V-POSITION: Moves the OSD screen up and down.
REAR TYPE : Choose rear camera recognition.
CAN : By connecting to “CAN” cable of the car gear,
changing to rear camera mode when shifting into
reverse. (Connect “CAN” cable of the power cable
to the “CAN” cable of the car gear)
LAMP : By connecting to the rear lamp of the car,
switch to rear camera mode when shifting into rear.
(Connect “Rear-C” cable of the power cable to the
rear lamp of the car)
SAFE ENABLE : If it is enable, HDMI, RGB, and A/V
mode doesn’t show up while driving. (Default : NO)
USM BEN9
NAVI MODEL :
Navigation model setting
BACK LIGHT :
LCD brightness setting
when the rear lamp is
"ON“
FCAM FUNC :
FCAM usage and time
setting
INFO
: System version
information
OSD & FACTORY MENU
BRIGHTNESS : Adjust screen brightness
CONTRAST : Adjust screen contrast
SHARPNESS : Adjust screen sharpness
USM-BENZ9-NTG 4.5 MANUAL Update : 2018. 09. 19
USM BENZ9
FACTORY RESET :
- YES: Reset OSD settings
8
7
IMAGE
PARK
FUNCTION
UTIL
SYSTEM VERSION
MAIN ：U1.8.08.01
※You can find the following cables in the rear side of OEM monitor.
INFO
* Connect provided CAN-H (white) cable
with OEM CAN-HIGH (brown + red) cable.
* Connect provided CAN-L(yellow) cable
with OEM CAN-LOW(brown) cable.
CAN -H
CAN - L
* Connect provided Jack by Jack cable to the rear of the OEM monitor.
* Connect the OEM LVDS cable to provided LVDS IN port.
※Press ◀(in remote control) 2 seconds, could
access the factory mode