Sune Technology QVI-Juke 2013 Manual

Your best partner for better driving
Update Date 2014.02.04
Model QVI-JK13-V1.1
Firmware Date
SUNE TECHNOLOGY CO.,LTD
No.9,Lane 606,Anping Rd,Tainan City 70849,TAIWAN
TEL:[phone] FAX:[phone]
Http://www.sune-tech.com
Shop http://www.carnavi-tech.com
SKYPE:sune_tech or hsin_han99
CarNavi-TechCarNavi-Tech

Warning
When installing the main unit, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screw, clips, and fittings.
Never detach, move or alter existing vehicle wiring, including
electrical grounds and straps. Alteration of existing vehicle
components may make vehicle unsafe to operate. Should be
no any electronic devices or magnetic pole around installation
place.
Air bags are vital part of a safety system. Never install main unit
in a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
accident.
Before installing, check the location of pipe, tank, electrical
cables and others.
Read and follow the instruction manual.
Wiring location must not interfere driving, get in or out from car.
Use electrical tape to insulate the ends of all wires, even if they
are not used. Proper insulation prevents arcs, shocks and fires.
When installation is complete, test all vehicle electrical systems
to ensure they operate correctly, including lights, horn, brake
lights, and emergency flashers.
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
Caution
All steps of installation should be done by well-trained specialist.
During installation ignition key should be taken off and after all
installation finish connect power cable with interface for the last
step.
Do not install the main unit in places where it ma be exposed to
dew condensation (around the air conditioning hose, etc), or in
locations where it may come in contact with water, high levels of
moisture, dust or oily smoke
Install wiring in a manner in which cables will not come in contact
with metal parts. The wiring may be damaged by contact with
metal parts, resulting in fire and shocks. Avoid all contact with hot
surfaces when wiring the main unit. High temperatures may
damage wiring, causing shorts, arcing and fires.
Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
Warning / Caution
CarNavi-TechCarNavi-Tech

Table of Contents
1. Specifications
1.1 Main Specifications
1.2 Features
1.3 System Diagram
1.4 Components
1.5 Exterior
2. Installation
2.1 Installation Diagram
2.2 Installation
3. Settings
3.1 Remote Control
3.2 Factory mode
3.2.1 Image, Park
3.2.2 UTIL
3.3 OSD(On Screen Display)
3.3.1 Analog RGB mode
3.3.2 Video mode
4. Trouble Shooting
1
2
3
4
5
6
7
15
16
18
19
20
21
CarNavi-TechCarNavi-Tech

1. Specifications
-1-
1.1 Main Specifications
1. Car Compatibility
NISSAN JUKE 2013 Model
2. Components
Video Interface* 1EA
Touch Sub board* 1EA
3. MULTIMEDIA INTERFACE input specification
2 * A/V input (video external input)
1 * CVBS(Rear Camera) input
1 * Analog RGB input (Navigation system output)
1 * LCD input (Car system input)
4. MULTIMEDIA INTERFACE output specification
1 * LCD output
5. Power specification
Input power : 8VDC ~ 16VDC
Consumed power : 4WATT
6. Switch input mode
- Through Factory setup
- Through remote control, can change input mode
- Through rear lamp cable, rear camera can be detected
CarNavi-TechCarNavi-Tech

1. Specifications
-2-
Improved Screen Display (user-oriented interface)
Provide power cable to connect with rear camera
Possible to select type for Parking assistant line
1.2 Features
CarNavi-TechCarNavi-Tech

1. Specification
-3-
1.3 System Diagram
DISPLAY
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
A/V 2
A/V 3 VIDEO
CIRCUIT
VIDEO MUX
MCU
Power Input
(+8VDC ~ +16VDC)
POWER
CIRCUIT A/V OUT HEADREST
MONITOR
Remote control Switch for source toggle
Car Installation
OEM LCD
Rear Camera
CarNavi-TechCarNavi-Tech

1. Specification
-4-
1.4 Components
REMOTE CONTROL * 1ea
(REMOTE0001)
REAR CAMERA
POWER cable * 1ea
(HARETC0002) IR cable * 1ea
MODE cable * 1ea
(HARETC0001)
(HIRCAB0002)
RGB cable * 1ea
(HNAVIC0004)
A/V cable * 1ea
(HAVCAB0017) POWER cable (24P) * 1ea
(HPOWER0051)
TOUCH OUT cable * 1ea
(HTOUCH0004)
Opposite side FFC cable * 1ea
(FFCABL0039)
Same side FFC cable * 1ea
(FFCABL0040)
Opposite side touch FFC cable * 1ea
(FFCABL0029)
Same side touch FFC cable * 1ea
(FFCABL0041)
<Main Board>
Sub-board * 1ea
(QCPASS0477)
Bracket * 1ea
(PRESET0147)
CarNavi-TechCarNavi-Tech

1. Specifications
-5-
1.5 Exterior
Dimension
Width 134mm
Length 84mm
Height 9mm
①TOUCH_OUT(OEM)
②COMMAND IN
③TOUCH_IN(OEM)
④LCD OUT
⑤POWER/NAVI/CAN
⑥A/V IN
⑦BUTTON
⑥⑦
③④
⑤
①②
CarNavi-TechCarNavi-Tech

2. Installation
-6-
2.1 Installation Diagram
AV1 AV2
Audio L
Audio R
AV/OUT REAR C
GND
CAN-L
IR
TPGGLE
SAFE
RCAM-PWR
REAR-C GND
GND
GREEN
VS
X-
Y-
ACC
CAN-H
IR-GND
P5V
GND
REAR-C
BLUE
RED
SYNC
X+
Y+
<POWER CABLE>
REAR
<Behind of Origna LCD><Original LCD PCB>
Original
touch
cable
Opposite side
FFC Cable
Opposite side
touch FFC
cable
Same side
Touch FFC cable
Same side
FFC Cable
Touch
Sub
board
※Please make sure that
the installation should be
carefully conducted to
avoid from the damage of
a monitor by
ESD(Electrostatic discharge)
and misalignment
while connecting the
module of a monitor with
cables.
CarNavi-TechCarNavi-Tech

2. Installation
-8-
2.2 Installation
①Remove the monitor from the car (see
picture above), Separate the LCD and the
body part.
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

2. Installation
-9-
2.2 Installation
①After dismantle the body, assemble provided bracket with bolt on
indicated places.
②After assembling the bracket, put provided SUB-BOARD with bolt
on indicated places.
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

2. Installation
-10-
2.2 Installation
①Separate steel plate on the back of LCD.
See picture above.
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

2. Installation
-11-
2.2 Installation
①After removing LCD board, separate the original cable
on indicated places and connect with provided FFC
cable on the other side.
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

2. Installation
-12-
2.2 Installation
①After connecting original gold cable with provided
touch board, connect with the other side of provided
FFC cable (see picture above).
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

2. Installation
-13-
2.2 Installation
①Put together the LCD, take out the cable from indicated spot
(see picture above).
②Connect the FFC cable (same side) with indicated place (see
picture above).
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

2. Installation
-14-
2.2 Installation
①Put together the still plate and take out the cable
as shown above. And assemble again with the
main board.
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

2. Installation
-15-
2.2 Installation
①Connect the cables as shown above.
②After connecting cables, assemble the board in order
as doing dismantling.
※Please make sure that the installation should be carefully conducted to avoid from the damage
of a monitor by ESD(Electrostatic discharge) and misalignment while connecting the module of a
monitor with cables.
CarNavi-TechCarNavi-Tech

3. Settings
-11-
3.1 Remote Control
Key
Function
POWER & PIP Unavailable
MENU Activating OSD menu
OK Making a selection, changing image display
▲Moving upward
▼Moving downward
◀Moving leftward
(If you press this button 2 seconds long, you can access the factory
mode.)
▶Moving rightward (If you press this button 2 seconds long, you can reset all the
data about user environment.)
CarNavi-TechCarNavi-Tech

3. Settings
-12-
3.2.1 Factory mode-Image, Park
IMAGE
Adjust navigation position and size
H-POSITION : Move display horizontally
V-POSITION : Move display vertically
FACTORY mode – Press ◀button 2 seconds long on the remote control.
PARK
PARK ENABLE : Selecting whether to
display the parking guide line or not
on rear gear (default : OFF)
PAS SETUP : Adjusting the position of
the parking guide line (available in
PARK SETUP -> V-POSITION, H-POSITION)
CarNavi-TechCarNavi-Tech

3. Settings
-13-
3.2.1 Factory mode-Image, Park
FACTORY mode – Press ◀button 2 seconds long on the remote control.
In H-POSITION, use ◁, ▷on remote control, to
adjust parking guideline left and right.
In V-POSITION use △, ▽on remote control, to
adjust parking guideline up and down.
H-POS
V-POS
Go to Factory Menu, choose PAS SETUP, by using OK button change H-POS → V-POS
CarNavi-TechCarNavi-Tech