Sunjoy D-GZ840PST-AS-16S User manual

Assembly Instructions
NS#:110102003/110102008
Item#:D-GZ840PST-AS-16S (Black Top) / D-GZ840PST-AS-26S (Faux
Copper Top)
Congratulations on your purchase of our SUNJOY 12’x10’ Hardtop Gazebo. Our clear, easy to
follow, step-by-step instructions will guide you through the assembly process from start to
finish. All you will need is a screwdriver, a hammer and two ladders (not included) whose
height is no less than 2.5 m.
●THIS UNIT IS
WARNING:
HEAV Y
●Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the area of the Gazebo construction.
!. Do not assemble this item alone. 4 people are recommended for safe
●Keep assembly area at least 6 feet from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
●Some parts may contain sharp edges. When assembling and using this product, basic safety
precautions should always be followed to reduce the risk of personal injury and damage to the
product. Please read all instructions before assembly and use.
●Check all bolts for tightness before use, and periodically check and tighten bolts as necessary.
●Assemble on level ground.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step number
in which the part is used
IMPORTANT
Please take time to read these instructions thoroughly and followeach step carefully for safe and easy
operation. Keep this manual forfuture reference.
For technical assistance on assembly or replacement parts. Please call Sunjoy Industries at
1-866-578-
6569 from 8:00 am EST to 8:00 pm PST or fax the replacement part form which is in the boxto
1-740-283-3549 or Email [e-mail] for assistance.

Big top frame A1 2
Big top bar B1 2
Small top support beam
C1 4
Small top connector D1 1
Pothook E1 1
Small top roof panel 1 F1 2
Small top roof panel 2 G1 2
Small top cover H1 4
Small top roof cover I1 1
PostA2 4
Beam connector C2 8
Base cover D2 4
Base E2 4
Slanting bar connector F2 4
Beam connector (upper) G2 4
Beam connector (down) H2 4
Short beam I2 4
Long beam J2 4
Support piece K2 8
Long pipe 1 L2a 2
Long pipe 2 L2b 2
Short pipe 1 M2a 2
Short pipe 2M2b 2
Parts List

Top slanting bar A3 4
Top beam B3 4
Long side left roof panel 1 C3 2
Long side right roof panel 1 D3 2
Long side left roof panel 2 E3 2
Long side right roof panel 2 F3 2
Long side left roof panel 3 G3 2
Long side right roof panel 3 H3 2
Short side roof panel 1 I3 2
Short side left roof panel 2 J3 2
Short side right roof panel 2 K3 2
Short side left roof panel 3 L3 2
Short side right roof panel 3 M3 2
Big roof panel cover (corner) N3 4
Big roof panel cover (middle) O3 4
Short beam of big roof (short side) (1) W1 2
Short beam of big roof (short side) (2) W2 2
Middle beam of big roof(short side) (1) W3 2
Middle beam of big roof(short side) (2) W4 2
Long beam of big roof (short side) (1) W5 2
Long beam of big roof (short side) (2) W6 2
Short beam of big roof (long side) (1) X1 2
Short beam of big roof (long side) (2) X2 2
Middle beam of big roof (long side) (1) X3 2
Middle beam of big roof (long side) (2) X4 2

Long beam of big roof (long side) (1) X5 2
Long beam of big roof (long side) (2) X6 2
Hardware Pack 1
AA M6*15 Bolt 96 PCS
BB M6 Washer 270 PCS
CC M6*60 Bolt 16PCS
DD M6 Nut 32 PCS
EE M6*35 Bolt 8 PCS
FF M6*15 Bolt 112 PCS
GG M6*70 Bolt 16 PCS
HH M6*45 Bolt 2 PCS
Z M6 Wrench 2 PCS

Fig.1: Fix Big top frame A1 and Big top bar B1 by using AA, BB.
Fig.2: Fix Small top support beam C1 and Big top frame A1 by using AA, BB.
Fig.3: Fix Small top support beam C1 and Small top connector D1 by using DD, BB, CC.
Fig.4: Screw the Pothook E1 into Small top connector D1.
Fig.5: Attach Beam connector C2 and Post A2 by using FF, BB.
Fig.6: Attach Slanting bar connector F2 and Post A2 by using FF, BB.
Fig.6-1: Insert Base cover D2 into Post A2, attach Base E2 and Post A2 by using AA, BB.
Fig7: Attach Beam connector G2(H2) to Long beam J2 and Short beam I2 by using GG, BB, DD.
Fig.7-1: Fix Short beam I2, Long beam J2 and Beam connector C2 by using FF, BB.
Fig.7-2: Fix Support piece K2 onto Post A2 and Short beam I2 (Long beam J2) by FF, BB.
Fig.8-1: Attach Top slanting bar A3 and Top beam B3 to Big top frame A1 by using FF, BB. (Do step fig8.1 and fig8.2 at
the same time, which is needed 2 pieces of 2M ladder.)
Fig.8-2: Attach Top slanting bar A3 to Slanting bar connector F2, Top beam B3 to Beam connector G2 by using CC,
BB, DD. (Do step fig8.1 and fig8.2 at the same time)

Fig.10: Fix Small top cover H1 onto Small
top support beam C1 by using EE, BB, then
fix Small top roof cover I1 and Small top
connector D1 by using HH,BB.
Fig.11: Attach Big roof top beam X6 (X5/W5/W6）to Top
slanting bar A3 by using AA, BB.
Fig.12: Attach Big roof top beam X5 to Top beam B3 by
using AA, BB. (Repeat the procedure for X1-X6, W1-W6.)
Fig.13: Attach Big roof top beam X4 to Top slanting bar A3
by using AA, BB (Repeat the procedure for X1-X4,W1-W4.)
Fig.13-1: Attach Long pipe L2a (L2b), Short pipe M2a (M2b) and Top beam B3 by using AA and BB.
Fig.13-2: Attach Long pipe L2a (L2b), Short pipe M2a (M2b) and Top slanting barA3 by using AA and BB.
AA M6*15 Bolt 44 PCS
BB M6 Washer 60 PCS
EE M6*35 Bolt 16 PCS
KK Φ8X260 Stake 16 PCS
Hardware Pack 2
Fig.9: Fix Small top roof panel 1 F1 and
Small top roof panel 2 G1 onto small Top
support beam C1 by using AA, BB.

Fig.14-1: Connect Long side left roof panel C3 and Long side left roof panel E3 for a whole piece.
Fig.14-2: Attach Long side left roof panel C3 and Long side left roof panel E3 onto the top frame by using AA, BB
(Repeat the procedure for D3, F3, G3, H3, I3, J3, K3, L3, M3)
Fig.15-1: Insert Big roof panel cover N3 into the hole of Small top support beam C1.
Fig.15-2: Then attach Big roof panel cover N3 and Top slanting bar A3 by using EE, BB, lock Big roof panel cover
O3 onto Top beam B3.
Fig.16: Put up Base cover D2, use Stake KK to fasten the gazebo on the ground. Put down B
ase cover D2 and
now your gazebo is ready for use.

IMPORTANT
1. Keep all children and pets away from assembly area. Children and pets should be
supervised while gazebo is being assembled.
:
2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction such as
a fence, garage, and house, overhanging branches, laundry lines or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe
assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the gazebo in
the ground. If you wish to secure the pavilion to a wood deck or concrete surface, use 16
anchors suited for these surfaces (anchors not included).
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may
require permits for installation and use. Some special procedures may be valid in your area.
9. While this gazebo is manufactured to withstand strong force winds through only the supplied
ground stakes, securing the gazebo to a deck, concrete patio or a stronger base, in areas
subject to frequent severe weather should be considered.
NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather
conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must
AA M6*15Bolt 4 PCS
BB M6 Bigger flatwasher 10 PCS
CC M6*60 Bolt 2 PCS
DD M6 Nut 3 PCS
EE M6*35 Bolt 2 PCS
FF M6*15 Bolt 4 PCS
GG M6*70Bolt 2 PCS
Backup Parts

be cleaned off regularly. Any damage caused by snow accumulation is not covered by the
warranty.
Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials
and workmanship of your item provided the item is maintained with care and used only for
personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1)
year. We don't reimburse for transportation or delivery costs, or compensate the individual or
any outside party for assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due
to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or
rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for
warranty claims. Warranty is to the original purchaser and is non-transferable. Any
replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow
exclusions or limitations on an implied warranty, the above exclusions and limitations may not
apply. This warranty gives you specific rights, and you may also have other rights, which vary
from state to state.
Maintenance:
Our iron/steel components for garden accessories and patio items are coated with rust
inhibiting paint that protects it from rusting. However, due to the nature of iron, surface
oxidation (rusting) will occur once these protective coatings are scratched.
This is a natural
process and is not a defect! To minimize this condition, we recommend care when assembling
& handling the product to prevent scratching the paint. Should any scratching or damage occur,
we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily
removed with a very light application of common cooking oil. If surface oxidation (rusting)
occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or
patio and cause damaging stains, which may be difficult to remove. This can be prevented if
measure is taken to keep the product from oxidizing.
For technical assistance on assembly or replacement parts. Please call Sunjoy Industries at
1-866-578-6569 from 8:00 am EST to 8:00 pm PST or fax the replacement part form which is
in the box to 1-740-283-3549 or Email [e-mail] for assistance.
Made in China

GAZEBO NETTING AND CURTAIN ASSEMBLY INSTRUCTIONS
Netting or Curatin is available separatley
Plastic ring 104 PCS
Fig.17: Hang Mosquito netting and curtain onto Long pipe 1 L2a (M2a, L2b, M2b) with Plastic ring , keep
pipe lay on the inside of curtain.