Sunjoy L-GZ076PST-1 User manual

1
IMPORTANT:
Please read and follow all safety statements, warnings, assembly instructions, use& care
directions, before attempting to assemble
WARNING:
•THIS UNIT IS HEAVY!
•Do not assemble this item alone for safety. Two persons are necessary.
•Some parts may contain sharp edges – especially as noted in manual. Wear protective gloves if
necessary.
•Do not play with the construction of the arbor. Children and pets should be supervised when they
are in area of the arbor. Do not allow the gate or the side panel to collide hard to avoid danger.
•Read all instructions before assembly and using this product.
•Select ideal location. Set out all parts on a clear and level surface prior to assembly. Ideally, the gazebo
frame should be set up in its desired location to avoid moving it after assembly.
•Use caution. During all the process of assembling, especially when lifting heavy or large parts, pay
attention to safety.
•Tools and Assistance. Ladder and screwdriver are self-provided. Whenever possible, assistance is preferred.
•Check for parts available. Before assembling your gazebo, be sure that you have all parts described in
the Parts List.
•Check for damaged parts. Before assembling your gazebo, check for damaged parts, any part that
appear damaged should be carefully checked to determine that it will be operated properly and perform its
intended function. Any part that is damaged should be properly repaired or replaced by a qualified
technician.
•Refer to assembly diagram. During assembly, it will be helpful to referring to the assembly diagram.
•Keep children away. Children must never be allowed in the work area. Do not let them handle parts and
Assembly Instruction
ITEM#L-GZ076PST-1
Summer Foliage Gazebo

2
tools. No people will be permitted to enter into work area except who is working.
•Caution for fabric: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC .This
tent is made of flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous contact with
a flame source.
Tools required: ladder, hammer screwdriver (not included)
S
p
are Hardware Pack
AA M5×15 mm screw 4 PCS
BB M5 Flat washer 4 PCS
GG Plastic Tie 4 PCS
DD M6×30 mm screw 2 PCS
EE M6 Flat washer 2 PCS
Touch up paint 1PC
AA M5×15 mm screw 44PCS
BB M5 Flat washer 44PCS
CC M6 nut 6PCS
DD M6×30 mm screw 8PCS
EE M6 Flat washer 14PCS
FF Plastic Washer 4PCS
W Stake 8PCS
GG Plastic Tie 48PCS
WW M6 wrench 1PC
Hardware Pack

3
Pole1 A1 2
Pole2 A2 1
Pole 3 A3 1
Pole 4 A4 1
Pole 5 A5 1
Fence1 B1 2
Fence2 B2 2
Screen C 6
Conner connector D 6
Top Pole E 6
Center fitting with hook F 1
Glass side bar top G 1
Side bar top support
(preassembled on the side bar top
G) H 2
Peg Fitting 1 I 2
Peg Fitting 2 J 2
Peg Fitting 3 K 2
Canopy S 1
Top canopy S1 1
Bug netting S2 1
Parts List

4
Fig.1
Step1. Insert Fence B1 into pole A2 ,then fix B1 by pulling
it down as Fig.1. Assemble Fence B1,B2 and Pole
A1,A3,A4,A5 in the same way according to picture above
Step 2. Use screw (AA), flat washer (BB) to connect Peg Fitting (K) to
Fence ( B1) and Pole (A4 orA2 ), as Fig.2.Assemble Peg Fitting (J) to
Fence(B2) and Pole(A1) in the same way . Do not tighten the screws.
Step 3. Use screw(AA)，flat washer(BB) to assemble Peg Fitting(I)
and Fence(B1 and B2) and Pole(A3 or A5), as Fig.3. Do not tighten
the screws.
Step 4. Use screw (AA) and flat washer (BB) to Fix the corner connector
(D) to the poles as Fig4-1. Insert the pin on the screen(C) into the
mounting hole on the pole and then pull down the screen, as
Fig4-2,.Use screw(AA) and flat washer(BB) to assemble the
screen( C) and corner connector ,as Fig4-3
B1
A2
Fig.3
Fig.2
Fi
g
.4-2 Fi
g
.4-3
Fig.4-1

5
Step 6. Assemble the canopy(S) on top frame(do not tighten),as
Fig6-1; Fully assemble top canopy(S1) on small top frame ,as
Fig.6-2 . Tie the bug netting around the top canopy to canopy and
then fully stretch canopy(S) and fix it to the end of corner connectors
(D), as Fig 6-3.
Step 5. Use screw(DD),flat washer(EE) and Nut(CC) to joint top
pole(E) and center connector(F) ,as Fig 5-1；And then lift
the assembled top frame to insert the other end of the top
pole(E) into the corner connector(D)，as Fig.5-2。
*After steps above, use screwdriver and wrench to tighten all
the hardware, but not too tight.
Step 7.Use screw(DD),flat washer(EE)and plastic washer(FF) to fix
the glass side bar top(G) to Pole(A3 and A4) and then use
wrench(WW) to tighten the screw, but not too tight so that the glass
bar top can flip smoothly ; Insert the pin on the pole into the hole at
the end of the bar top support (H) and then put the dowel attached to
the little chain into the pin on the pole to set up the side bar top as
Fig 7. When not in use, the side bar top support (H) can go
separately with the poles and the top can stand vertically
Fig.5-2
E
D
Fig.6-1
Fig.6-2
Fig.6-3
S1
S
Fig.7
S1
S
Fig.5-1

6
W
S2
USE & CARE:
1. This Gazebo is not a permanent structure and should be disassembled & stored away after use.
2. Do not repack your gazebo until completely dry.
3. This Gazebo must be assembled by Four adults or more.
4. This Gazebo must not be left erect in windy conditions.
5. Loading limit of the hook is 45lbs
6. Loading limit of the ring is 25lbs
7. Loading limit of the glass side bar top is 33lbs.
8. Steel components for garden accessories and furniture are treated with rust inhibiting paint that protects them
from rust. However, due to the nature of steel, surface oxidation (rusting) will occur if this protective coating is
scratched. This is a natural process. To minimize this condition, it is recommended that care be taken when
assembling and handling the product in order to prevent the paint from being scratched. If scratching or damage
occurs, it is recommended that the area be touched-up immediately with rust inhibiting paint, which is included in
the package. Surface rust can be removed easily using a very light application of common cooking oil. If surface
oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may start dripping onto the deck or
patio, which may cause damaging stains that may be difficult to remove.
Limited Warranty
Sunjoy Industries warrants to the original purchaser that this item is free from defects in workmanship and
materials for a period of six (6) months from the date of purchase, provided the item was factory-sealed at the time
of purchase and is maintained with care and used only for personal, residential purposes. Should any
manufacturing defect arise within this warranty period, Sunjoy Industries will repair or replace (at our option) any
defective merchandise upon proof of purchase; however, transportation and delivery costs, as well as labor and
material charges to remove or replace parts, remain the responsibility of the purchaser. A purchaser of an "open
box," previously-returned, or "clearance" item, as well as original purchasers outside of the warranty period, may
obtain replacement parts from Sunjoy Industries for products in current production, at nominal cost.
Exclusions: Items used for commercial, contract, or other non-residential purposes, or items damaged due to
Step 8.Use stake (W) to fix the gazebo on ground, as
Fig8-1; Lastly use the plastic ties to fix the bug netting(S2)
to the bar at the back of the screen as Fig8-2, and tie the
bug netting to the poles. Now the gazebo is ready for use.
Fig.8-1
Fig.8-2
W

7
acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not
covered. Proof of purchase (dated register receipt) is required for warranty claims. Warranty is to the original
purchaser and is non-transferable. Any replacement of warranted items will be in the original style and color, or a
similar style and color if the original is unavailable or has been discontinued. As some states do not allow
exclusions or limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty
gives you specific rights, and you may also have other rights, which vary from state to state.
CUSTOMER SERVICE:
Please do not return this product to the store. For technical assistance on assembly or replacement parts call
Sunjoy Industries at 1-866-532-9557 from 8:30 AM to 5:30 PM EST or Email [e-mail] for
assistance.