Sunjoy 10’x12’ Benen Gazebo L-GZ215PST-1 User manual

1
Assembly Instructions
ITEM# L-GZ215PST-1
10’x12’ Benen Gazebo
IMPORTANT:
Please read and follow all safety statements, warnings, assembly instructions, use & care directions,
before attempting to assemble
1. When installing and assembling your gazebo, it is recommended that 4 or more adults are involved.
2. Do not use the unit during an electrical storm, as there is a remote chance of getting struck by
lightning.
3. Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury, possibly even
death.
4. Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will occur
to the structure.
5. Never barbecue under this gazebo or use lanterns that contain open flames.
6. This package contains small items and plastic bags that should be kept away from children.
7. Insure that all connectors & poles are firmly secured in position fully. It is important to do so before use
so as to avoid collapsing or damage to the item, which could result in injury.
Tools required: ladder, hammer screwdriver (not included)

2
Post A 4
Base B 4
Base cover C 4
Short beam (1) D 2
Short beam (2) E 2
Long beam (1) F 2
Long beam (2) G 2
Connecting slice H 8
Corner Connector I 4
Short side connector J 2
Long side connector K 2
Big top pole L 4
Short side pole M 2
Long side pole N 2
Long mosquito pipe O 4
Short mosquito pipe P 4
Big top connector Q 1
Small top connector R 1
Small top bar S 4
Decor finial T 4
Pothook U 1
Parts List

3
AA M6X15 (Bolt)
TBZ00306015HQ 48 PCS
BB M6 (Washer)
TBZ10406HQ 72 PCS
CC M6X15 (Bolt)
TBZ00106015HQ 24 PCS
Z M6 (Wrench) 1 PC
Hardware Used in Step 1
Small top canopy V 1
Big top canopy W 1
Wall X 1
Mosquito net Y 1
Parts List

4
Fig.1: Put the base cover C on the top of post A, then use bolt (AA) and wash (BB) to connect the base (B)
and post A.
Note: Make sure the slots on C and A are at the same side.
Fig.2: Connect the beam F (D）and beam G（E）, by using the bolt (CC) and washer (BB).
Fig.3: Attach the connected bar to stand pole (A) by using bolt (CC) and washer (BB) then use bolt (AA) and
washer (BB) to fix the beam and stand pole tightly.
Fig.4: Fix the mosquito pipe P（O）onto the beam, use bolt (AA) and washer (BB).
AA M6X15(Bolt)
TBZ00306015HQ 12 PCS
BB M6 (Washer)
TBZ10406HQ 16 PCS
DD M6X35 (Bolt)
TBZ00306035HQ 4 PCS
EE M6 (Nut)
TBZ20106HQ 4 PCS
Hardware Used in Step 2
Fig.5, Fig.5-1: Attach the connecting slice (H)
to the beam and post (A), by using bolt (AA)
and washer (BB).

5
Fig.6: Fix the corner connector (I ) on the top of the post (A), by using bolt (AA) and washer (BB).
Fig.7: Fix the pothook (U) onto the big top connector (Q), then insert the big top beam (L), long side beam
(N), short side beam (M) into Big top connector (Q).
Fig.7-1: Insert the big top beam (L) into the corner connector (I).
Fig.8: Fix the connector J (K) and beam using the bolt (AA) and washer (BB).
FF
Φ6X260MM Round nail
TBZ10608260HQ 16 PCS
GG Plastic ring 88 PCS
Hardware Used in Step 3
Fig.8-1: Insert the short and long side beam M (N) into the short and long side connector J (K).
Fig.9: Insert the small top bar (S) into the small top connector (R). Install the small canopy(V) and tie up the
strap.
Fig.10: First put the big top canopy (W) onto the top of the gazebo (Do not fully spread), then use bolt (DD),
washer (BB) and nut (EE) to connect small top with corner top bar (L) of big top.

6
Note: Please keep these extra parts since they are not covered in product warranty. Use these extra parts to
fasten the electrical cord with the top beam if a light is used.
Fig.11: Spread the big canopy (W) and fix the hooks on the canopy
Fig.12: Put the decor (T) onto top of post.
Fig.13: Connect the mosquito net (GG) with mosquito pipe P (O) by plastic
ring (GG). Use plastic ring (GG) to hang the wall (X) onto pipes which under
the beam.
Fig.14: Use plastic ring to fix the wall (X) into the underneath pipe of the
mosquito pipe (O) (P).
Fig.15: Put up the base C, using nail (FF) to fasten the gazebo.
Extra Parts
XX Electrical cord tie 6 PCS

7
USE & CARE:
1. This gazebo is not a permanent structure and should be disassembled & stored away after use.
2. Do not repack your gazebo until completely dry.
3. This gazebo must be assembled by two adults or more.
4. This gazebo must not be left erect in windy conditions.
5. Loading limit of the hook is 33 lbs.
WARNINGS:
1. Assembly Instructions must be followed.
2. Pegs supplied must be used to hold this gazebo in place when upright.
3. Warranty does not cover damage due to extreme weather conditions.
4. Do not use candles, matches or open flames of any kind in or near a tent.
5. Do not cook inside the tent.
6. Build campfires downwind and several meters away from a tent and be sure to fully extinguish campfires
before leaving a campsite or before retiring for the night.
7. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use
battery-operated lanterns whenever possible.
8. Do not refuel lamps, heaters or stoves inside a tent.
9. Extinguish or turn off all lanterns before going to sleep.
10.Do not smoke in a tent.
11.Do not store flammable liquids inside a tent
12. KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent is made of
flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous contact with a flame source.