Sunnydaze Decor HB-785 User manual

CAUTION:
SHARP EDGES
USE EXTREME CAUTION
◄ WEAR GLOVES DURING ASSEMBLY ►
L-SHAPED GALVANIZED STEEL
RAISED GARDEN BED
HB-785
Read the assembly instructions carefully and follow the care instructions. Save this document for future reference.

Page 1 / 4
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
  
ALong Panel 4
BMedium Panel 2
CEnd Panel 2
DSmall Corner 6
EBracket 4
FCrossbar 4
1M5x12mm Bolt 64
2Wing Nut 64
G3286 10/2022
CHOKING HAZARD — This item contains small parts that can
be swallowed. Keep children and pets away during assembly.
WARNING
(not included)
Phillips Screwdriver

Page 2 / 4G3286 10/2022
ASSEMBLY
Review all steps and understand assembly before beginning.
Do not fully tighten hardware until all components have been loosely assembled.
STEP 1
C: 2
D: 4
1: 16
2: 16
STEP 2
A: 4
1: 16
2: 16
STEP 3
B: 2
D: 1
1: 8
2: 8
Align End Panel (C) with
Corner (D) and secure using
four M5x12mm Bolts (1) and
Wing Nuts (2).
Repeat this step until both
end panels have corners
installed on each side, as
shown.
IMPORTANT: Identify the rolled
edges of the panels and ensure they
are installed facing the inside of the
garden bed.
Ensuring the rolled edges
are facing the inside of the
garden bed, align Long
Panels (A) with the end
panel corners and secure
using four bolts and wing
nuts.
Repeat this step until all
four long panels have been
secured, as shown.
Set assembled components
aside.
Align two Medium Panels
(B) with one Corner (D) and
secure using eight bolts and
wing nuts.

STEP 4
E:2
1: 4
2: 4
STEP 5
D: 1
E:4
1: 8
2: 8
STEP 6
F: 4
1: 8
2: 8
Page 3 / 4G3286 10/2022
Align the assembled
components.
On the inside of the garden
bed, align the four mounting
holes in Bracket (E) with the
panels.
Secure only the center two
mounting holes with bolts
and wing nuts as shown.
Repeat this step to connect
components on the opposite
side.
Ensuring the corner piece
is facing inward, align one
Corner Panel (D) and two
Brackets (E) with the long
panels.
Secure only the center two
mounting holes with bolts
and wing nuts as shown.
Align two Crossbars (F)
diagonally with the bracket
outside edges of the bracket
and secure using bolts and
wing nuts as shown.
Repeat to secure the
remaining crossbars to the
opposite side.
IMPORTANT: Do not install
hardware into the top and bottom
mounting holes.
IMPORTANT: Ensure the bolt is
installed in the correct direction, with
the wingnut on the outside of the
bracket as shown.

Page 4 / 4
WARNING!
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,

G3286 10/2022
STEP 7
1: 8
2: 8
Secure the top and bottom
of each bracket with bolts
and wing nuts.
Fully tighten all hardware
from all steps.
USE & CARE
• This garden bed provides ergonomic access to plants and can eliminate the need to till the soil each year as
long as the soil is not packed down. Avoid stepping in the bed!
• Prepare the site before installation. Level the ground and remove existing vegetation. Landscaping fabric
can be used under the beds; a double layer is recommended for beds placed directly on a lawn.
• A layer of gravel or stone can be used at the bottom for improved drainage.
• Loosely hand-tighten all nuts and bolt sets first, position the bed, then tighten. After assembly, check that all
fastening points are secured.
• Galvanized metal beds do not require maintenance and are built to withstand years of exposure to the
elements.
• The galvanized finish protects the steel from corrosion. Over time, galvanized steel will fade, and some
discoloration is normal. Minor surface rust on edges and hardware is to be expected and should not affect
the structural integrity of the product.
• Do not stand on, or lean objects against the bed wall as doing so may damage the product.
• Do not let children play in or around the garden bed.
• Use of this item for applications other than gardening will void the product warranty.
SAFETY STATEMENTS & WARNINGS

If you experience issues with assembly or the product was damaged during shipping,
please contact our customer service team through one of the methods mentioned at the top of page 1.
Please have the item number and order information ready to expedite response time.