Sunnydaze Decor LARGE RECTANGLE GALVANIZED STEEL RAISED GARDEN... User manual

73385, 657796 09/2023
LARGE RECTANGLE GALVANIZED
STEEL RAISED GARDEN BED
Review all care and assembly information carefully before using this product. Save this manual for future reference.

Page 1 / 3
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Save the packing slip.
CHOKING HAZARD — This item contains small parts that can be
swallowed. Keep children and pets away during assembly.
WARNING
  
ASide Panel 4
BEnd Panel 2
CCorner 4
DCenter Bar 2
EM6x10mm Bolt 48
FWing Nut 44
CAUTION:
SHARP EDGES
USE EXTREME CAUTION
◄ WEAR GLOVES DURING ASSEMBLY ►
 (not included)
Phillips Screwdriver

73385, 657796 09/2023 Page 2 / 3
ASSEMBLY
Review all steps and understand assembly before beginning.
Do not fully tighten hardware until all components have been loosely assembled.
STEP 1
B: 2
C: 4
E: 16
F: 16
STEP 2
A: 4
E: 16
F: 16
STEP 3
E: 12
F: 12
Align two Corners (C)
with one End Panel (B)
and loosely secure using
M6x10mm Bolts (E) and
Wing Nuts (F).
Repeat with the remaining
end panel and corners.
IMPORTANT: Identify the rolled
edges of the panels and ensure they
are installed facing the inside of the
garden bed.
Ensuring the rolled edges
are facing the inside of the
garden bed, align two Side
Panels (A) with the corners
and loosely secure using
eight bolts and wing nuts.
Repeat to loosely secure
the remaining side panels to
the other end panel.
Align the double mounting
holes on the side panels.
Loosely fasten six bolts and
wingnuts into the mounting
holes exactly as shown; do
not install hardware into the
inner-most mounting holes
on the top and bottom of the
unit.
IMPORTANT: One end of the side
panels has double mounting holes,
install the single-hole side to the
corners.
IMPORTANT: The location of
hardware installation in the diagram
is for maximum stability of the unit,
the center bar must be installed in the
correct location to achieve optimal
structural support.

73385, 657796 09/2023 Page 3 / 3
USE & CARE
• This garden bed provides ergonomic access to plants and can eliminate the need to till the soil each year as
long as the soil is not packed down. Avoid stepping inside the bed!
• Prepare the site before installation. Level the ground and remove existing vegetation. Landscaping fabric
can be used under the beds; a double layer is recommended for beds placed directly on a lawn.
• A layer of gravel or stone can be used at the bottom for improved drainage.
• Loosely hand-tighten all nuts and bolt sets first, position the bed, then tighten. After assembly, check that all
fastening points are fully secured.
• Galvanized metal beds do not require maintenance and are built to withstand years of exposure to outdoor
elements.
• The galvanized finish protects the steel from corrosion. Over time, galvanized steel will fade, and some
discoloration is normal. Minor surface rust on edges and hardware is to be expected and should not affect
the structural integrity of the product.
• Wear gloves during assembly to prevent personal injury.
• Do not stand on, or lean objects against the bed wall. Doing so may damage the product.
• Do not let children play in or around the garden bed.
• Using this item for applications other than gardening will void the product warranty.
SAFETY STATEMENTS & WARNINGS

If you experience issues with assembly or the product was damaged during shipping,
please contact our customer service team through one of the methods mentioned at the top of page 1.
Please have the item number and order information ready to expedite response time.
WARNING:
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage


STEP 4
D: 2
E: 4 Align one Center Bar (D)
with the bottom mounting
holes, loosely secure by
hand-tightening two bolts.
Then, repeat to secure the
remaining center bar to the
top of the unit.
Fully tighten all hardware
from all previous steps.