Sunricher 2819S User manual

N L
N L
N L
LED Dimmer Remote , 4 Zone,
RF/WIFI
Brief introduction of buttons
Indicator: indicate the state of
remote control
Brightness button Brightness wheel
4 zones: each zone can save
3 color or modes
25% Brightness 50% Brightness
ON/OFF of all zones
75% Brightness 100% Brightness
Save button S1 S2 S3
Four zones/areas
Press-button Dimmer
Receivers work with WIFI-RF converter to be controlled by smart phone
Wiring diagram
1) Receiver Connection Diagram for Single Unit
Parameter
Remote
Power Supply
12-36VDC
SR-1009FA
110V-230VAC
Power Supply
12-36VDC
SR-1009FA
110V-230VAC
Lear ning Key LED CONTROLLER Lear ning Key LED CONTROLLER
Receiver
Single color
LED Strip
Single color
LED Strip
Single color
LED Strip
Single color
LED S trip
4x5A
Single color
LED Strip
Single color
LED Strip
2x10A
Product Size
2) Receiver Connection Diagram for Multiple
Units
Power Supply
12-36VDC 110V-230VAC
Note:
One receiver can work with one dimmer
One Dimmer control multiple receivers
The power supply chosen must be 20% higher than the actual load
Lear ning Key
Lear ning Key
120.0
Lear ning Key
SR-1009FA
LED CONTROLLER
4x5A
SR-1009FA
LED CONTROLLER
4x5A
SR-1009FA
LED CONTROLLER
4x5A
Single color LED S trip
Single color LED Strip
Single color LED Strip
Single color LED S trip
Single color LED S trip
Single color LED Strip
Single color LED Strip
Single color LED S trip
Single color LED S trip
Single color LED Strip
Single color LED Strip
Single color LED S trip
55.0
17.0
w hi t e
43 2 1
w hi t e
43 2 1
w hi te
43 2
w hi te
1 4 3 2 1
w hi t e
43 2 1
Operation Voltage
Operation
Frequency
DIMENSIONS
ø/h (mm)
Remarks
3.6VDC
434MHz/868MHz
55x120x17
load 3pcs 7 AAA (1.5V)
batteries
Iuput Voltage
Current
Output
Remarks
12-36VDC
4x8A
4x(96-288)W
Constant voltage

adjust the color temperature
and brightness
S1
S2
S3
Operation
Learning (matching)
a. Do wiring according to connection diagram
b. Wake up the remote control by touching ON/OFF button.
c. Press learning button on receiver.
d. Touch any zone button on remote control.
e. Then touch brightness wheel.
f. Connected LED light will blink to confirm zone designation.
g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
Note 1: To choose a master from slaves by jumper for each zone.
Short circuit for master.
Open circuit for slave.
Each zone only can set one master controller. After a period of time, the master will do synchronization
operation to keep the same color or mode of all slaves in one zone.
Note 2: Each remote control 4zones (areas) receivers, each area can be learned as many receivers as we
can.
Each receiver maximally can be controlled by 8 different remote controllers.
Dim wheel
Choose zone number , for example, and , then touch , choose the brightness you
want, zone 1 and 3 will indicate corresponding brightness as we touched.
Brightness Up & Down Button
Long Press button to dim down/up brightness, the dimming direction will change every time after pressing
switch. For example, the first long press is brightness up, it will be dimmed down when long press again.
Brightness level button
Select zone from . Press , the corresponding zones will be 25% brightness. Press ,
the corresponding zones will be 50% brightness. Press , the corresponding zones will be 75%
brightness. Press , the corresponding zones will be 100% brightness.
WarrantyAgreement
1) We provide lifelong technical assistance with this product:
2-year warranty. We print date on every products.The warranty is for free repair or replacement and covers
manufacturing faults only .
For faults beyond the 2-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, v ibration etc. af ter purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near harmful
chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy tothe customer.
Save and recall button
a. Save Color temperature:
b. Recall: select zone button which we want recall from ,
then short press save button
Safety& Warnings
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6) Please ensure that the cable is secured tightly in the connector
7) For update inf ormation please consult your supplier.
select zones from
LED lighting flash twice
indicate save successful
long press one save button
from S1 S2 S3 for 2-3 second