Sunricher SR-1009F Series User manual

RF wireless LED remote controller
Six zones/areas
Press-button RGBW controller
Model:SR-2819 with SR-1009Fxx
Parameter
Wiring diagram
Product Size
Brief introduction of buttons
Product introduction
SR-2819 RGBW remote controller has 6 different zones. It can get Red/ Green/ Blue/ White color directly. The
remote controller can save up to 6 colors or 6 modes into corresponding buttons (1-6 positions) for each zone.
You can choose any color through color wheel. you can set the system as RGB 3-channeloutput, or RGBW 4-
channel output
Receivers work with WIFI-RF convertor to be controlled by smart phone
Part No. Iuput Voltage Remarks
Current
SR-1009FA 12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
SR-1009EA 12-36VDC Constant voltage
4x(96-288)W4x8A
Remote
Part No. Operation Voltage DIMENSIONS
ø/h (mm)
Operation
Frequency
SR-2819 3.6VDC 48x140x16
434MHz/868MHz
Receiver
SR-1009FA3 12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
SR-1009FA7 12-36VDC Constant current
4x(8.4-25.2)W4x700mA
Remarks
load 3pcs 7 AAA (1.5V)
batteries Note:
One receiver can work with 1-8pcs SR-2819
One SR-2819 control multiple receivers
The power supply chosen must be 20% higher than the actual load
56
23 1
R G B
4
Indicator: indicate the state of
remote control
White channel: the 4th channel
Touch color wheel
Pause/Run button: 10 modes
built-in
R/G/B channels
ON/OFF of all zones
Speed down under dynamic mode
Return previous status button
Save button: save up to 6 colors
or modes into 6 positions
(6-zone buttons)
6 zones: each zone can save
6 color or modes
Speed up under dynamic mode
Brightness: dim up
Brightness: dim down
1)Receiver Connection Diagram for Single Unit
2) Connection Diagram for Multiple UnitsReceiver
Power Supply
12-36VDC
LN
110V-230VAC
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
Power Supply
12-36VDC
LN
110V-230VAC
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
140.0
48.0
17.0

Safety & Warnings
Warranty Agreement
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6)
7) For update information please consult your supplier.
Please ensure that the cable is secured tightly in the connector
1) We provide lifelong technical assistance with this product:
3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
Operation
Learning (matching)
a. Do wiring according to connection diagram
b. Wake up the remote control by touching ON/OFF button.
c. Press learning button on receiver.
d. Touch any zone button on remote control.
e. Then touch color wheel.
f. Connected LED light will blink to confirm zone designation.
g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
Note 1: To choose a master from slaves by jumper for each zone.
Short circuit for master.
Open circuit for slave.
Each zone only can set one master controller. After a period of time, the master will do synchronization
operation to keep the same color or mode of all slaves in one zone.
Note 2: Each remote control 8 zones (areas) receivers, each area can be learned as many receivers as
we can.
Each receiver maximally can be controlled by 8 different remote controllers.
Touch button is to switch on/off of each corresponding color.
Hold your finger on button to dim brightness of each corresponding color. There are total 8 levels
of brightness.
Note: If you press R, then press G, then it is mix color of R and G. If you want to get G color directly, please
press R to switch off of R first. Then press G.
Running&Pause Button
a. Press pause&run button ,mode will run. Press it once, it runs one mode. Press button again, it stops,
then press one more time, it will enter next mode. There are total 10 build-in modes.
b. Pause&run button can work with S button , it can save modes into different zone.
c. Touch button one by one, such as press button 1,2,3,4,5,6, then
Press button. Zone 1,2,3,4,5,6 will run synchronized mode, after long press, LED lighting will flash twice,
they will switch to chasing running mode, long press again to switch back.
Return button
Touch button to return previous color or running mode.
Speed up and Speed down Button
Touch button to speed down when mode is running, touch button to speed up when mode is running.
Brightness down or up button
Short/long press button to dim down brightness of RGB channels, Short/ long press button to dim up RGB
channels.
“W” channel is separated from RGB channels, so we can only long press button to dimming“W” channel.
Save Button
a. How to save color into different position per zone?
b. How to save mode into different position per zone?
c. Recall
Choose zone number form , then press button, and press the position button which color or
mode saved into.
R G B
R G B
456
23 1
RGBW button
456
23 1
ZONE Touch color wheel for select an ideal color
Select R/G/B/W color by press R G B
or
Long press button(the blue
indicator will be on) for saving
Choose position( ) to save colorany button
456
23 1
POSITION
Press any zone
button you want
For example, press zone button 1, then touch color wheel for orange color, then press S button
(the blue indicator will be on),then choose position button 3. That’s to say, we save orange color
from zone 1 into position 3.
So each zone can save 6 colors. 6 zones can save 36 colors.
456
23 1
ZONE
Press button for select an ideal mode
Press button(the blue
indicator will be on) for saving
Choose position( ) to save modeany button
456
23 1
POSITION
Press any zone
button you want
456
23 1