Sunricher SR-1009 Series User manual

SR-2818&SR-1009XX full touch RGBW
remote controller User Manual
SR-2818 RGBW remote controller is full touch remote controller which has 8 different zones. It
can get Red/ Green/ Blue/ White color directly. The remote controller can save up to 8 colors or 8
modes into corresponding buttons (1-8 buttons) for each zone. You can choose any color through
color wheel. There is a USB port to charge internal battery.
2.Performance Parameter
2.1 Sender: (SR-2818)
Operation voltage: 3.6VDC
Operation frequency: 434MHZ / 868MHZ
Battery: Lithium battery.
2.2 Receiver: (SR-1009FA/ SR-1009F3/ SR-1009F7))
Input voltage: 12-36VDC
Output voltage: 12-36VDC
SR-1009FA: 4 channels x 5A, 4channels x (60-180W)
SR-1009F3: 4 channels x 350mA, 4 channels x (4.2-12.6W)
SR-1006F7: 4 channels x 700mA, 4 channels x (8.4-25.2W).
4.Wiring Diagram
1.Brief introduction
Note: SR-2818 can also control WIFI receiver (SR-1009FAWi/ SR-1009F3Wi/ SR-1009F7Wi).
When WIFI receivers are not controlled by software, then you can use SR-2818 remote. The
operation will be the same.
①Color wheel
②Indicator
③ON/OFF button
④R/G/B/W button
⑤Save color button
3.Brief introduction of buttons
⑥Play & Pause button
⑦Return previous status button
⑧Speed down & speed up button
⑨Brightness button
⑩Zone button
①Learning button
②Jumper
③12-36VDC input
④4 channels output
PRI:
Uin=12-36VDC
Iin=20.5A
SEC:
Uout=4x(12-36)VDC
Iout=4x5A
Pout=4x(60-180)W
SR-1009FAWi
12-36VDC
W
TEMP RANGE:-20℃-+50℃
Learn ing
Switc h
Power Supply
Input 12-36VDC
LN
110-240V
R
G
B
R
G
B
W W
USB port OFF
ON
Indicator will be on while remote is charging.
Indicator will be off while it’s full power.
Bottom
1 2
Remote: SR-2818 Receiver: SR-2818

5.Operation
1. Do wiring according to connection diagram
2. Learning process
a. Wake up the remote control by touching ON/OFF button.
b. Press at learning button on receiver.
c. Touch any button on remote control.
d.Then touch color wheel.
e.Connected LED light will blink to confirm zone designation.
f . Press at learning button on receiver over 5 seconds until LED light flash, then delete the
learned ID.
Note: To choose a master from slaves by jumper for each zone.
Short circuit is to be slave.
Open circuit is to be master.
Each zone only can set 1 slave to be master. After a period of time, the master will do
synchronization operation to keep the same color or mode of all slaves in one zone.
3. Touch button is to switch on/off of each corresponding color.
Hold your finger on button to dim brightness of each corresponding
color. There are total 8 levels of brightness.
Note: If you press R, then press G, then it is mix color of R and G. If you want to get G color
directly, please press R to switch off of R first. Then press G.
4. Touch button is to play mode or do pause operation of mode. There are 10 build-in
modes in this button.
5. Touch button is for saving color or mode at 1-8 buttons. Each zone (Each receiver) can
save 8 modes or 8 colors. Operation is show as below:
If you want to play your saved color or mode, choose zone number from 1 to 8, then touch ,
then touch saved number in that zone. Then it will play.
6. Touch button to return previous color or running mode.
7. Touch button to speed down when mode is running, touch button to speed up
when mode is running.
8. Touch button to dim down whole brightness of LED lighting, touch button to dim
up whole brightness of LED lighting.
9. Touch button one by one, such as press button 1,2,3,4,5,6, then
press button, then saved color or mode in button 1,2,3,4,5,6 will run chasing mode one by
one.
PRI:
Uin=12-36VDC
Iin=3.2A
SEC:
Uout=4x(12-36)V DC
Iout=4x700mA
Pout=4x(8.4-25. 2)W
SR-1009F7Wi
12-36VDC
W
TEMP RA NGE:- 20℃-+50℃
Learni ng
Switch
Power Supply
Input 12-36VDC
LN
110-240V
+
+
34
Other application
SR-2818WITR can convert RF signal to WIFI signal. Then it makes smart phone control SR-
1009FA RF receiver. Via SR-2818WITR, one smart phone can control several RF receivers.
Choose zone number ----> Touch button, mode is running -----> save
favorite mode to button in 1 zone-----> touch (over 2 seconds) to save
program into zone until the blue indicator on.
Choose zone number ----> Touch color wheel to get favorite color
-----> save favorite color to button in 1 zone-----> touch (over 2 seconds) to
save color into zone until the blue indicator on.