Sunricher SR-ZG9001T3-RGBW-US User manual

RGBW Wall Mounted Touch ZigBee Remote Controller
09.ZG2TU.04782
Function introduction
Important: Read All Instructions Prior to Installation
Front side
Back side
19.4 mm 43.58 mm
65.58 mm
AC Power input
L L
83.00 mm
ZigBee controller
N N
AC POW ER I NPUT
Product Data
Transmission Range
(free field) 30m
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimming Range 0.1%-100%
Power Supply 100-240V AC
Operation Frequency 2.4GHz
Dimensions 120x75x29.1mm
Protection Type Ip20
Red channel:Click to turn off/on
Press and hold down to increase/
decrease light intensity
Blue channel:Click to turn off/on
Press and hold down to increase/
decrease light intensity
Green channel:Click to turn off/on
Press and hold down to increase/
decrease light intensity
Click to get white color mixed by R,
G, B channels
RGB color wheel, slide touch to
select RGB color
ON/OFF button, click to turn
ON/OFF all, press and hold down to
search and pair to ZigBee network
or factory reset the controller
Press and hold down to
increase/decrease light intensity
Click to select warm white, cool
white, natural white mixed by RGB
Play/Pause button, click to play
or pause built-in running effects,
press and hold down to speed
up/down the effect
Group button, click to select
corresponding group, press and
hold down to turn ON/OFF it Note: This remote supports 3
groups for binding max. 30
lighting devices. • DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.
Safety & Warnings
• ZigBee RGBW remote based on ZigBee 3.0
• Full touch glass interface, smooth RGB color and light
intensity control
• Enables to pair ZigBee lighting devices via touchlink
commissioning without coordinator
• Supports find and bind mode to pair with ZigBee
lighting devices
• Supports 3 groups for binding lighting devices
• 2.4 GHz global operation
• Transmission range up to 30m
• Compatible with universal ZigBee Gateway products
• Compatible with universal RGBW ZigBee lighting
devices
Operation
1.This ZigBee RGB remote is a wireless transmitter that communicates with a variety of ZigBee
compatible systems. This transmitter sends wireless radio signals that are used to remotely control a
compatible system.
2.This ZigBee remote supports 3 groups for binding max. 30 lighting devices and enables to control
RGB ZigBee lighting devices.
ZigBee Clusters Supported by This Remote Are As Follows:
Input clusters:
• Basic • Power Configuration • Identify • Diagnostics
Output clusters:
• Identify • Group • On/off • Level control • Color control • Ota
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
Step 1: Remove the remote from
previous zigbee network if it has
already been added to it, otherwise
pairing will fail. Please refer to the part
"Factory Reset Manually".
Step 2: From your zigbee controller or
hub interface, choose to add device or
accessory and enter Pairing mode as
instructed by the controller.
Step 3: Press and hold down until LED
indicator turns on.
Step 4: Immediately short press to
search nearby network, indicator
flashes every 1 second, 20 seconds
timeout if there is no network. Indicator
will then blink 5 times quickly for
successful pairing.

ZigBee Lighting Device
ZigBee Lighting Device
ZigBee Lighting Device
4. TouchLink to a Zigbee Lighting Device
Note: 1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices.
2) TouchLink after both added to a ZigBee network, each remote can link with max. 30 devices.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the remote can control the linked lighting devices.
ZigBee Lighting Device
< 10cm
5. Removed from a Zigbee Network through Coordinator or Hub Interface
6. Factory Reset Manually
7. Remove a Touchlink Paired ZigBee Lighting Device
Step 1: Set the Touchlink paired
zigbee device to start TouchLink
commissioning, please refer to its
manual to learn how.
8. Factory Reset a Lighting Device (Touch Reset)
Note: the device shall be added to a network, the remote added to the same one or not added to any network.
Note: 1) After pairing successfully, the remote information will appear on the controller or hub interface.
2) No remote information will appear on the hub interface if pairing to Philips Hue Bridge.
Step 1: Set the zigbee lighting device
to start TouchLink commissioning,
please refer to its manual to learn how.
From your ZigBee controller or hub
interface, choose to delete or reset
the remote as instructed, indicator
flashes 3 times quickly to indicate
successful removing.
9. Find and Bind a Zigbee Lighting Device
Note: Each remote can bind max. 30 lighting devices.
Note: All configuration parameters
will be reset after the remote is
reset or removed from the network.
Step 1: Press and hold down until
LED indicator turns on.
Step 2: Immediately short press 5
times continuously, indicator flashes
3 times quickly to indicate successful
reset.
Step 2: Bring the remote within 10cm
of the lighting device.
Step 3: Short press any button to
choose a group to touchlink.
Step 4: Press and hold down until LED
indicator turns on.
Step 5: Immediately short press to
start TouchLink commissioning of the
remote. LED indicator flashes fast for
3S, then flash 6 times slowly to
indicate successful pairing to the
device and the light connected to the
device will blink twice.
< 10cm
Step 2: Bring the remote within 10cm
of the lighting device.
Step 3: Short press the group button
that the device was linked to.
Step 4: Press and hold down until LED
indicator turns on.
Step 5: Immediately short press twice
to start TouchLink removing of the
remote. LED indicator flashes fast for
3S, then flash 6 times slowly to
indicate successful removing.
Step 1: Set the zigbee device to start
TouchLink commissioning, refer to its
manual.
< 10cm
Step 2: Bring the remote within 10cm
of the lighting device.
Step 3: Press and hold down until LED
indicator turns on.
Step 4: Immediately short press 5
times to start Touch Reset of the
remote. LED indicator flashes fast for
3S, then flash 3 times slowly to
indicate successful reset.
Step 1: Start find and bind mode on the
Zigbee lighting device (initiator node)
and enable it to find and bind target,
refer to its manual.
Step 2: Short press a group button that
you would like to bind the device to.
Step 3: Press and hold down until LED
indicator turns on.
Step 4: Short press to enable the
remote (target node) to find and bind
initiator.LED indicator flashes 4 times
for successful binding or twice if
binding fails.
Note: Make sure the device and remote already added to the same zigbee network.

ZigBee Lighting Device
ZigBee Lighting Device
10. Find and Unbind a Zigbee Lighting Device
11. Clear All Find and Bind Mode Paired Lighting Devices
12. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required)
Step 5: Add more remotes to the network as you would like.
Step 6: Factory reset the lighting devices that you would like to add to the network, refer to their manuals.
Step 7: Touchlink to pair the added remotes and lighting devices you would like to add, the devices will be added
to the network through Touchlink, refer to their manuals.
14. How to Check Whether the Remote Belongs to a Network or not
Short press any other buttons except group buttons, indicator blinking means the remote has already been
added to a network, no blinking of indicator means the remote does not belong to any network.
Installation
Wiring diagram
AC 100-240V
AC Power
50/60Hz
L L
ZigBee Controller
N N
AC POWER INPUT
Step 1: Start find and bind mode on the
Zigbee lighting device (initiator node)
and enable it to find and bind target,
refer to its manual.
Step 2: Short press the group button
that the device already bound to.
Step 3: Press and hold down until LED
indicator turns on.
Step 4: Short press twice to enable the
remote (target node) to find and unbind
initiator. LED indicator flashes 4 times
for successful unbinding or twice if
unbinding fails.
Step 1: Short press to choose the
group that you would like to unbind all
devices.
Step 2: Press and hold down until LED
indicator turns on.
Step 3: Short press 5 times
continuously to clear all bound lighting
devices . LED indicator flashes 4 times
for successful unbinding.
Step 1: Factory reset the remote and
the lighting device, refer to their
manuals.
Step 2: TouchLink the remote and
device to setup a network, refer to their
manuals.
Step 3: Short press button to enable
the network to discover and add
devices, LED indicator will flash twice.
180 seconds timeout, repeat the
operation. Step 4: Set another remote into
network pairing mode and pair it to the
network, refer to its manual.
< 10cm
13. OTA
The remote supports firmware updating through OTA, and will acquire new firmware from zigbee controller or
hub every 10 minutes automatically.