Sunricher SR-2819T8 User manual

R G B W
S- S+
B- B+
W+
P- P+
1 2 34
5678
RF RGBW Remote Controller 09.289T8.04168
Indicator: indicate the state of
remote control
Click to switch CW,
NW, WW mixed by RGB
4.5V(3xAAA battery)
Function introduction
Important: Read All Instructions Prior to Installation
Output RF signal
Operation Frequency 869.5/916.5/434MHz
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 131.4x43.8x24.3mm
Front side
Back side
• High sensitive & high stable, fast & precise color control.
• Enable to control 8 zones separately.
• 10 changing modes.
• Compatible with all universal series RF receivers
• 1 receiver can be paired by max 8 different remote controls.
• Waterproof grade: IP20
Product Data
Safety & Warnings
Power Supply 4.5V(3xAAA battery)
R G B W
S- S+
B- B+
Touch color wheel, touch to
choose RGB color tone
8 zones
Click to choose the zone/zones,
Press and hold down to turn on/off
corresponding zone
Press and hold down to increase
light intensity of RGB
Press and hold down to
decrease light intensity of RGB
Speed up under dynamic modeSpeed down under dynamic mode
R/G/B/W 4 channels.
Click to switch on/off each channel;
Press and hold down to increase/
decrease light intensity of each
channel
W+
P- P+
1 2 34
5678
Built-in 10 dynamic modes,
P- is previous mode,P+ is next mode.
• This device contains AAA batteries that shall be stored and disposed properly.
• DO NOT expose the device to moisture.
Pair with RF receiver(Method 1)
Step 4:Choose and click a zone number(e.g. zone 4)
Step 3:Click the “Learning Key” button on RF receiver or re-power on the receiver
three times continuously to set it into pairing status
Learning Key
RF LED Receiver
Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the
instruction of RF receiver that you would like to pair with.
Step 5:Touch the color wheel, LED lights connected with the RF receiver flicker
once means the receiver is paired with zone 4 successfully.
Step 2:Click ON/OFF button to activate the remote
Pair with RF receiver(Method 2)
Step 4:Choose and click a zone number(e.g. zone 4) twice, then press and hold it
continuously and quickly within 10 seconds, LED lights connected with the RF receiver
flicker once means the receiver is paired with zone 4 successfully.
Step 3:Power off and power on the receiver
Learning Key
RF LED Receiver
Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the
instruction of RF receiver that you would like to pair with.
Step 2:Click ON/OFF button to activate the remote
R G B W
S- S+
B- B+
W+
P- P+
1 2 34
5678

If you use multiple receivers, you have two choices:
Option 1: have all the receivers in the same zone, like zone 1
Lear nin g Key
RF LED Rec ei ve r
Zone 1
Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4
Zone 1 Zone 2 Zone 3
RF remote
RF remote
Lear nin g Key
RF LED Rec ei ve r
Lear nin g Key
RF LED Rec ei ve r
Lear nin g Key
RF LED Rec ei ve r
Lear nin g Key
RF LED Rec ei ve r
Built-in 10 color changing modes are as follows:
Mode 1: Any two colors of RGB mix fade-in & fade-out
Mode 2: RGB three colors mix fade-in & fade-out
Mode 3: RGB three colors mix fade-out & fade-in
Mode 4: RGB flash
Mode 5: RGB three colors fade-in & fade-out successively
Mode 6: RGB three colors fade-in successively
Mode 7: RGB three colors fade-out successively
Mode 8: RGB three colors jump changing successively
Mode 9: R&B two colors mix fade (R in B out), then G fade-in, then R&B mix fade (R out B in), then G fade-out
Mode 10: B fade-out, then G&B mix fade (G out B in), then R&G mix fade (R out G in), then R fade-in
How to stop running mode of single color LED light caused by RGBW sender interference:
1. When pairing single color LED light to a single color remote, it might be interfered and paired by nearby
RGBW senders, which might control the single color light into running mode. The running mode can not be
stopped by the paired single color remote or by delete pairing.
2. Then we need this remote, and pair the remote to the receiver via above “Pair with RF receiver(Method 2)”,
then touch the color wheel to stop the running mode.
3. Then delete pairing and pair the receiver to the single color remote again, it can be controlled by the remote
again.