Sunrise Medical Guardian IC-5307 Installation guide

Guardian® Homecare Bed
User Instructions & Warranty
Manual Bed Models IC-5307 IC-5207 & IC-5107
Semi Electric Bed Models IC-5310 IC-5210 & IC-5110
Full Electric Bed Model IC-5410
Lit de soins àdomicile Guardian®
Mode d’emploi et garantie
Lit manuel modèles IC-5307 IC-5207 & IC-5107
Lit semi-électrique modèles IC-5310 IC-5210 & IC-5110
Lit électrique 3 positions modèle IC-5410
Cama para Cuidados en el Hogar Guardian®
Manual de Instrucciones y Garantía
Modelos de Cama Manual IC-5307 IC-5207 & IC-5107
Modelos de Cama Semieléctrica IC-5310 IC-5210 & IC-5110
Modelo de Cama Totalmente Eléctrica IC-5410

2English Sunrise Listens
SUNRISE LISTENS
Thank you for choosing a Sunrise Medical bed. We want to hear your questions or com-
ments about this manual, the safety and reliability of your bed and the service you receive
from your Sunrise Medical supplier. lease feel free to write or call us at the address and
telephone number below:
Sunrise Medical
Customer Service Department
7477 East Dry Creek arkway
Longmont, CO 80503
[phone] or [phone]
FOR ANSWERS TO YOUR QUESTIONS
Your authorized supplier knows your bed best and can answer most of your questions about
bed safety, use and maintenance. For future reference, fill in the following.
Supplier: _________________________________________________
Address: _________________________________________________
Telephone: _______________________________________________
Serial #: _________________________________________________
Date/ urchased:___________________________________________
This manual contains important safety and maintenance instructions. lease read
it carefully before using your homecare bed and refer to it as often as needed for
safe and efficient use.
If you have questions regarding the safe use and/or assembly, maintenance or
specifications of your bed, contact Customer Service at 800-333-4000, 303-218-
4600 or from Canada at 800-263-3390. lease have the Model and Serial Number
of the product available.
For service and repair, remember your authorized Sunrise Medical dealer is able to
provide the assistance you need.
Keep this manual in a safe place for future reference.

Table of Contents 3
English
TABLE OF CONTENTS
INTRODUCTION .................................................................................... 2
TABLE OF CONTENTS ............................................................................. 3
IMPORTANT WARNINGS......................................................................... 4
BED WEIG T CAPACITY ......................................................................... 5
SET-UP................................................................................................ 5
ASSEMBLY ........................................................................................... 6
Manual Bed Assembly ......................................................................... 6
Semi-Electric Bed Assembly ................................................................. 8
Full-Electric Bed Assembly................................................................... 10
OPERATION.......................................................................................... 12
Manual Bed Operation......................................................................... 12
Semi-Electric Bed Operation ................................................................ 13
Full-Electric Bed Operation .................................................................. 13
Locking/Unlocking Casters................................................................... 13
MAINTENANCE ..................................................................................... 14
CLEANING / SPECIFICATIONS................................................................. 15
TROUBLES OOTING .............................................................................. 16
IMPORTANT WARNINGS FOR ACCESSORIES............................................... 17
WARRANTY .......................................................................................... 19
FRANÇAIS............................................................................................... 20
ESPAÑOL ................................................................................................ 38

IMPORTANT WARNINGS
(See pages 17 & 18 for Important Warnings for Accessories)
WARNING
RISK OF SERIOUS INJURY OR DEAT . Bed power cord has a hospital-grade 3-prong
grounding plug. Do not defeat grounding safety feature by using 3-prong to 2-
prong adapter. If necessary, have outlet ground reliability checked by a qualified
electrician. Failure to do so could result in shock or electrocution.
WARNING
RISK OF SERIOUS INJURY. When operating the bed, make sure that the occupant
is positioned within the boundaries of the bed and that no extremities extend
over the side or between the bed rails.
WARNING
RISK OF SERIOUS INJURY. Closely monitor children and high-risk individuals in or
around bed.
WARNING
RISK OF SERIOUS INJURY. Electromagnetic Interference (EMI) may influence elec-
tronic equipment. Exercise caution when using hand-held transceivers around the
electric bed. If unintended movement occurs due to EMI, unplug the electric bed
immediately. Leave unplugged during transmission, otherwise injury may occur.
WARNING
POSSIBLE DAMAGE OR INJURY. The homecare bed is not intended to be used as a
means of transport. Use an approved transport device when transporting a
patient.
WARNING
POSSIBLE DAMAGE OR INJURY. The homecare bed was designed to be used in a
home care setting only and is not intended for use in nursing homes or hospitals.
WARNING
POSSIBLE DAMAGE OR INJURY. Do not allow more than one person on the bed at a
time.
WARNING
POSSIBLE DAMAGE OR INJURY. Distribute body weight evenly over surface of bed.
Do not put entire body weight only on raised foot or head sections of bed, other-
wise damage to bed may occur.
WARNING
Risk of serious injury. Keep cord away from heated surfaces.
WARNING
Possible damage or injury. Do not use outdoors.
SAVE T ESE INSTRUCTIONS.
4English Important Warnings

BED WEIG T CAPACITY
The homecare bed has a capacity of 450 pounds (204 kg) evenly distributed on the sleep-
ing surface. This is the total weight of the occupant, mattress, bedding, accessories and
other medical equipment in use. Exceeding the weight limit will void the warranty.
SET-UP
Check all bed components for obvious damage to the carton or its contents. Inspect each
item carefully for dents, scratches or any other visible damage. If damage is evident, con-
tact your local Sunrise Medical dealer.
WARNING
Before assembling bed, inspect all parts for shipping damage. If damage is evi-
dent, do not use bed. Contact qualified personnel immediately.
CAUTION– Do not plug in or operate bed controls before bed is completely assembled.
Damage to bed components or injury may occur.
The bed is packaged in three separate cartons:
1. Bed Ends (Figure 1)
•Headboard
•Footboard
•Hi/Lo Connecting Rod (not included with fixed height or two crank models)
•Four casters (two locking and two non-locking)
2. Foot Spring (Figure 2)
•Foot spring (electric beds include pendant, control box and power cord)
•Emergency crank handle (electric beds only)
3. Head Spring (Figure 3)
For electric beds, check for damage to power cord and plug. Inspect control box for damage
to the connectors and make sure the motor plugs fit properly into the control box. See
(Figure 48) in Maintenance section for correct installation of connecters into control box.
WARNING
POSSIBLE INJURY. Do not use bed if power cord or plug is damaged. Refer servic-
ing to qualified technician.
Set-up 5
English
ead Foot Bed
Model No. Bed Type Section Section End Set
IC-5410 Full-Electric IC-5000 IC-5490 IC-5401
IC-5310 Semi-Electric Single Crank Hi/Lo IC-5000 IC-5890 IC-5301
IC-5210 Semi-Electric Two Crank Hi/Lo IC-5000 IC-5890 IC-5200
IC-5110 Semi-Electric Set Height IC-5000 IC-5890 IC-5100
IC-5307 Manual Single Crank Hi/Lo IC-5000 IC-5770 IC-5301
IC-5207 Manual Two Crank Hi/Lo IC-5000 IC-5770 IC-5200
IC-5107 Manual Set Height IC-5000 IC-5770 IC-5100
Major Bed Components Part Numbers
1
2
3

ASSEMBLY
MANUAL BED ASSEMBLY
WARNING
After any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely.
CAUTION– Do not operate bed controls before bed is completely assembled. Damage to
bed components or injury may occur.
Connecting ead and Foot Sections
1. lace the head end at a right angle (90 degrees) to the foot end. The head end
should be on its side to your left with the center mounting hooks to your right
(Figure 4). The foot end (with crank handles) should be to your right with the head
spring pull tube at the top and the center mounting rivets pins facing to the left.
2. Engage the head end hooks into the foot end pins (Figure 5).
NOTE– It may be necessary to lift slightly on the head end or foot end to secure the
mounting hooks and pins.
3. Rotate the back section 90 degrees, making the frame assembly a straight line
(Figure 6).
Connecting Fabric of ead and Foot Sections
1. Turn foot crank clockwise to raise the foot end (see Manual Bed Operation) (Figure 7).
2. Hook together all the links on the mattress surface (Figure 8).
Connecting ead Spring Drive Tube
1. Disconnect the head drive tube assembly from the side frame of the foot spring by
removing the hitch pin, grommet and washer from the clevis pin (Figure 9).
2. Extend the inner drive tube shaft until the detent button clicks into the adjustment
hole of the outer drive tube. Make sure the detent button protrudes through the
adjustment hole of the extended drive tube arm (Figure 10). The drive tube arm will
line up with the lift arm slot.
3. Attach the drive tube end assembly to the lift arm of the head spring by inserting
the clevis pin into the lift arm slot. Reconnect the grommet and washer and fasten
with hitch pin (Figure 11).
4. After assembling frame, lay bed flat.
6English Assembly
4
6
8
9
7
5

Assembling the Bed Ends
NOTE– The headboard is taller than the footboard.
1. Stand the headboard next to the head section of the bed.
2. Lift the head end and engage the pins in the frame into the hooks on the headboard
(Figure 12). Leaning the headboard back slightly will help the pins fit into the
hooks more easily.
3. Lift the foot section of the bed and engage the pins on the frame into the hooks on
the footboard in the same manner.
WARNING
Make sure head and foot ends are securely locked to the head and foot boards
before using bed.
Installing the Casters
NOTE– For maximum locking stability, assemble the two locking casters diagonally at
opposite ends of the bed.
Install all four casters simply by raising the bed ends from the floor and pushing the stem
up into the caster socket in each bed leg (Figure 13).
Assembling i/Lo Connecting Rod
NOTE– This section does not apply to fixed height or two crank models.
NOTE– The connecting rod has two sections: The inner rod has a detent button, and the
outer rod has two positioning holes and one storage position hole.
1. Remove plastic caps from both ends of connecting rod.
2. Depress detent button on inner rod and insert into outer rod. Slide the inner rod in
place and engage the detent button into the first positioning hole.
3. The connecting rod mounts directly into the head and foot end gearbox output shafts
(Figures 14 & 15).
Assembly 7
English
10
11
12
13
14
15

SEMI-ELECTRIC BED ASSEMBLY
WARNING
After any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely.
CAUTION– Do not operate bed controls before bed is completely assembled. Damage to
bed components or injury may occur.
Connecting ead and Foot Sections
1. lace the head end at a right angle (90 degrees) to the foot end. The head end
should be on its side to your left with the center mounting hooks to your right
(Figure 16). The foot end (with motors) should be to your right with the head
spring pull tube at the top and the center mounting rivets pins facing to the left. For
electric foot ends, the motors should be to your right, and for manual foot ends the
crank handles will be to your right.
2. Engage the head end hooks into the foot end pins (Figure 17).
NOTE– It may be necessary to lift slightly on the head end or foot end to secure the
mounting hooks and pins.
3. Rotate the back section 90 degrees, making the frame assembly a straight line
(Figure 18).
Connecting Fabric of ead and Foot Sections
1. ress the “FOOT U ” button on the hand pendant (see Semi-Electric Bed Operation) or
use emergency crank to turn motor shaft clockwise to raise the foot end (Figure 19).
2. Hook together all the links on the mattress surface (Figure 20).
Connecting ead Spring Drive Tube
1. Disconnect the head drive tube assembly from the side frame of the foot spring by
removing the hitch pin, grommet and washer from the clevis pin (Figure 21).
2. Extend the inner drive tube shaft until the detent button clicks into the adjustment
hole of the outer drive tube. Make sure the detent button protrudes through the
adjustment hole of the extended drive tube arm (Figure 22). The drive tube arm will
line up with the lift arm slot.
3. Attach the drive tube end assembly to the lift arm of the head spring by inserting
the clevis pin into the lift arm slot. Reconnect the grommet and washer and fasten
with hitch pin (Figure 23).
4. After assembling frame, lay bed flat.
8English Assembly
16
18
20
21
19
17

Assembling the Bed Ends
NOTE– The headboard is taller than the footboard.
1. Stand the headboard next to the head section of the bed.
2. Lift the head end and engage the pins in the frame into the hooks on the headboard
(Figure 24). Leaning the headboard back slightly will help the pins fit into the
hooks more easily.
3. Lift the foot section of the bed and engage the pins on the frame into the hooks on
the footboard in the same manner.
WARNING
Make sure head and foot ends are securely locked to the head and foot boards
before using bed.
Installing the Casters
NOTE– For maximum locking stability, assemble the two locking casters diagonally at
opposite ends of the bed.
Install all four casters simply by raising the bed ends from the floor and pushing the stem
up into the caster socket in each bed leg (Figure 25).
Assembling i/Lo Connecting Rod
NOTE– This section does not apply to fixed height or two crank models.
NOTE– The connecting rod has two sections: The inner rod has a detent button, and the
outer rod has two positioning holes and one storage position hole.
1. Remove plastic caps from both ends of connecting rod.
2. Depress detent button on inner rod and insert into outer rod. Slide the inner rod in
place and engage the detent button into the first positioning hole.
3. The connecting rod mounts directly into the head and foot end gearbox output shafts
(Figures 26 & 27).
WARNING
POSSIBLE INJURY OR DAMAGE. After the bed has been assembled, check to make
sure that all components are secured properly in place and all fasteners are tight
before use.
WARNING
POSSIBLE INJURY. Do not leave electric bed plugged in while not in use.
Installing the Pendant
Install the hand pendant by plugging its connector into the matching socket in the
control box.
NOTE– Semi-electric beds use a four-function pendant for head and foot functions.
Leveling the Bed
For semi-electric beds with a single crank, turn the center hi/low crank counterclockwise
(see Semi-Electric Bed Operation). The lowest end of the bed will soon stop moving down-
ward, but the higher end of the bed will continue moving down. When both bed ends are at
their lowest, your bed will be level.
NOTE– If you are having difficulty leveling the bed because only one bed end moves up or
down, check to be sure all center drive tube pins and slots are properly engaged.
Assembly 9
English
22
23
24
25
26
27

FULL-ELECTRIC BED ASSEMBLY
WARNING
After any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely.
CAUTION– Do not operate bed controls before bed is completely assembled. Damage to
bed components or injury may occur.
Connecting ead and Foot Sections
1. lace the head end at a right angle (90 degrees) to the foot end. The head end
should be on its side to your left with the center mounting hooks to your right
(Figure 28). The foot end (with motors) should be to your right with the head
spring pull tube at the top and the center mounting rivets pins facing to the left.
2. Engage the head end hooks into the foot end pins (Figure 29).
NOTE– It may be necessary to lift slightly on the head end or foot end to secure the
mounting hooks and pins.
3. Rotate the back section 90 degrees, making the frame assembly a straight line
(Figure 30).
Connecting Fabric of ead and Foot Sections
1. ress the “FOOT U ” button on the hand pendant (see Full-Electric Bed Operation) or
use emergency crank to turn motor shaft clockwise to raise the foot end (Figure 31).
2. Hook together all the links on the mattress surface (Figures 32).
Connecting ead Spring Drive Tube
1. Disconnect the head drive tube assembly from the side frame of the foot spring by
removing the hitch pin, grommet and washer from the clevis pin (Figure 33).
2. Extend the inner drive tube shaft until the detent button clicks into the adjustment
hole of the outer drive tube. Make sure the detent button protrudes through the
adjustment hole of the extended drive tube arm (Figure 34). The drive tube arm will
line up with the lift arm slot.
3. Attach the drive tube end assembly to the lift arm of the head spring by inserting
the clevis pin into the lift arm slot. Reconnect the grommet and washer and fasten
with hitch pin (Figure 35).
4. After assembling frame, lay bed flat.
10 English Assembly
28
30
32
33
31
29