Sunrise Medical Quickie Xtender User manual

S E C T I O N E N G L I S H
A. PRE-INSTA TION
1. Prep the chair
a. Remove the wheels.
b. Place the chair on a flat work surface or workbench for best instal-
lation results
c. Make a mark on both sides of the frame where the center of the
Camber tube lines up with the frame.
d. Using a 10mm wrench and 4mm hex key remove the Seat sling and
seat rail (Fig 1). Set the hardware aside for re-assembly.
2. Remove the Backrest assembly
a. Using a 10mm wrench and 5mm hex key, remove the backrest
bracket to frame hardware (A) from both sides of the chair. Set
the hardware aside for re-assembly of the backrest later.
b. Pull on the backrest release strap (B) to release the locking pins
(C) from the backrest bracket.
c. Remove the Backrest assembly (D).
d. Using a pair of needle-nose pliers, remove C-clip (E) from the
release strap assembly. Remove the assembly and hardware, and
set it aside for re-assembly.
e. Remove the tube end-cap (F), or Swing away armrest receiver.
3. Remove the Axle Plate/Camber tube assembly
a. Using a 4mm hex key, loosen the two socket head screws (G) on
both sides of the chair, so that you can move the whole assembly.
b. Slide the assembly carefully and evenly off of the rear chair frame.
c. The chair is ready for installaion of the Xtender unit.
1
2
3
Parts for installing the pin assembly
1. 2x Pin
2. 4x O-Ring
3. 2x Washer
4. 2x Standard Axle plate
Tools needed for the complete assembly:
1. 2mm,5mm, 6mm hex key
2. 10mm, 12mm wrench
3. 19mm wrench
4. 2x 7/6” wrench
5. 1x Socket wrench
6. 1x 7/16” Socket
7. Needle-nose pliers
XTENDER KIT INSTALLATION INSTRUCTIONS
QUICKIE 5R/QUICKIE GT
2
Please read these instructions carefully before beginning the installation. Failure to understand and follow installation instructions
may result in injury to installer and/or end user and may void the warranty.
If you have any questions call Sunrise Medical Technical support at 800-333-4000
3
A
B
C
EF
D
G
Xtender Mounting parts:
1. 4x large black hex nut
2. 2x index axle washer
3. 2x stopper arm
4. 2x small stopper arm
5. 2x Button head screw
6. 4x washer plain
7. 2x axle sleeve
8. 2x boss
9. 2x 3” hex bolt
10. 2x 2 3/4” hex bolt
11. 4x 2 1/4” hex bolt
12. 8x washer
13. 8x nylock nut
14. 8x spacer
G
1

B. PIN ASSEMB Y
NOTE–In most cases, the Xtender kit will be shipped from the factory with the pins
pre-installed in the correct position.
Xtender guide pins for STANDARD axle plate (GT&Q5R)
1. The Xtender hub has raised numbers by each hole to aid in the correct place-
ment of the pins.
2. Attach the washer and O-rings to the pin as shown in (figure 1)
3. Starting on the left hub of the Xtender assembly, Install the pin assembly in
hole #4 as shown in (figure 2) and hand tighten.
4. Assemble the second pin for the right hub. Install the pin assembly in hole #2
(Figure 3).
5. Use a torque wrench and 12mm socket, tighten the pins to a torque of 85 in-lbs.
C. XTENDER MOUNTING HARDWARE
Assembly of Frame mounts and axle brackets:
1. Using a 10mm wrench, and a 5mm hex key, assemble and attach frame mounts
(A) to the axle plate brackets (left and right) (B). Do not fully tighten until the
mounting hardware is on the frame.
2. Be sure that the axle plate brackets hole position (C) is the same orientation
on both sides. The arrow in (Fig. 6) shows direction of the front of the chair.
3. Use (Fig 7) for reference to correctly assemble the mounting hardware.
4. After assembling the Right and eft side mounting assemblies (Fig. 6) slide them
on the frame of the chair to the same distance from the frame tube ends.
5. Snug the Frame clamp hardware (D) (do not tighten).
6. Tighten the frame mount hardware (E)
4 5 6
7 8
XTENDER KI T I N S TA L L AT I O N QUICKIE GT A N D 5R
SU NRISE MEDICA
0
15
15
30
30
45
TORQUE !TORQUE !
4
5
eft side (5R and GT)
A
6
Right side 5R and GT
PIN
O-RINGS
WASHER
Hole #4
Hole 2
78
Right side
Full Assembly Reference
B
C
A
D
E
E
E
0
15
15
30
30
45
TORQUE !TORQUE !

SU NRISE MEDICA
XTENDER KI T I N S TA L L AT I O N QUICKIE GT A N D 5R
D. ANTI-TIPS, AX E P ATES, AND STRUTS
WARNING
Attention dealers and qualified technicians, make sure that the installed axle plate
provides the same seat to floor height as the original approved setup.
1. Install the Anti-tip receivers
a. Using a 10mm wrench and socket, assemble and install the anti-tip
receiver(A) and hardware (B) to the axle plate bracket (C).
b. Tighten the hardware to 85 in-lbs.
c. Install the second anti-tip receiver on the other side of the chair see
(Fig 8) for reference.
2. Install the Axle plates and struts on the left side of the chair.
a. Using a 10mm wrench and socket, assemble and install the axle plate
(D) and hardware (E) to the axle plate bracket (C), and strut (F).
b. Attach the second strut (G) and tighten the hardware to 85 in-lbs.
3. Install the Axle plates and struts on the right side of the chair.
a. Repeat steps 1 and 2 to Install the axle plates and anti-tips on the
other side of the chair see (Fig 8) for reference.
E. AX E S EEVES AND STOPPER ARMS
WARNING
Attention dealers and qualified technicians, make sure that the axle placement
and center of gravity of the chair is in the same location as it was before the
installation.
1. Install axle sleeves and stopper arms
a. Install axle sleeve nut (H) to the axle sleeve ( I )
b. Install stopper arm( J ) over axle sleeve ( I ).
c. Install the assembly through axle plate slot (K).
d. On back side, place index washer ( ) and axle sleeve nut (H) on axle
sleeve. Hand tighten the nuts.
e. Install Boss (M) through axle plate slot and install screw (N) through
the small stopper arm (O) and washer (P).
f. Hold Boss (M) tight with adjustable wrench and tighten screw (N)
with hex key wrench until it is snug but can still move in the axle
sleeve slot.
2. Adjust and tighten the stoppers:
a. With hardware loose, place Xtender wheel on axle plate, through
sleeve and adjust stopper arm so Xtender wheel pin fits in stopper
arm.
b. Mark location of Boss (M) on axle plate with tape and slowly remove
the Xtender wheel.
c. Tighten Boss (M) and screw first, keeping Boss (M) on mark. Tighten
the axle sleeve nuts.
d. Torque axle sleeve nuts to 30 ft-lbs and screw to 85 in-lbs.
e.Repeat steps 1and 2 for both sides.
10 11
99
A
B
C
B
10
11
eft side (5R and GT)
eft side (5R and GT)
K
D
E
E
F
E
G
H
I
J
H
M
N
O
P
Right side (5R and GT)
H
H
M
K
O
P
I
J
0
15
15
30
30
45
TORQUE !TORQUE !
0
15
15
30
30
45
TORQUE !TORQUE !

SU NRISE MEDICA
XTENDER KI T I N S TA L L AT I O N QUICKIE GT A N D 5R
F. XTENDER INSTA ATION
1. Measure and adjust for balance and symmetry.
a. Check that the axle brackets (A), axle sleeves (B), and frame clamps
(C) have been installed evenly from side to side.
b. Once the assembly is balanced, and symmetrical, Use a torque
wrench and socket wrench to tighten all hardware to the correct
torque.
2. Re-install Backrest and Backrest brackets
a. Refer to Pre-installation section and install the backrest using the
reverse of the procedure given in step 2.
b. Use a torque wrench and socket wrench to check all hardware for
correct torque, and make sure the backrest can be adjusted, and that
it folds and locks properly.
c. Attach the Xtender wheels to the chair (Fig. 12 & 13)
G. CHECKOUT
1. Torque pins and Axles
a. Make sure the Torque Pins (Fig. 13) are seated properly and tight.
b. Use a torque wrench and socket wrench to check all hardware for
correct torque.
1. Double-check Orientation and Torque on all Hardware.
a. Check that the chair rolls smoothly and evenly..
b. Use a torque wrench and socket wrench to check all hardware for
correct torque.
DEA ER/TECHNICIAN WARNING
WARNING
Attention dealers and qualified technicians, do not operate or service this device
without first reading the owners manual. If you do not understand the instruc-
tions and warnings in the owners manual please contact the Quickie Technical
Service Department before operating and/or servicing the Quickie device.
Failure to do so may result in damage and/or injury.
For more information and important warnings, you can find the Xtender
owner’s manual at www.Sunrisemedical.com/ Help-support.
12
13 14 15
©2015 Sunrise Medical (US) C
05.15 MK-100157 Rev.A
Customer Service: 800.333.4000
www.SunriseMedical.com
Sunrise Medical • 2842 Business Park Ave. • Fresno, CA 93727 • USA
In Canada [phone]
13
12
eft side, arm
angled up
Right side, arm
angled down 14
AX E BRACKET 15
XTENDER
TORQUE PIN
HAS TO BE
F USH
AX E S EEVE
DETENT BA S
(EXTENDED)
A
C
B
C
D