Super Circuits SYRF04 Assembly instructions

4-Camera H.264 Security System
Installation and Setup Guide
Products: SYRF04, SYRF04LCD
SYRF04LCD System Shown with Dome Cameras
PLEASE READ THIS MANUAL BEFORE USING YOUR SYSTEM, and always follow the
instructions for safety and proper use. Save this manual for future reference.
SYRF04-04LCD_QuickSetup
3/30/11

ii www.supercircuits.com
CAUTION
Operate this device only in environments where the temperature or humidity is within the recommended range. Operation
at extreme temperatures or in very high or low humidity levels may cause electric shock and shorten the life of the
product.
CAUTION
Installation and servicing should be performed by qualied and experienced personnel only. DVR should always remain
OFF during any installation process.
CAUTION
Do not use the camera if fumes, smoke or a strange odor is emitted from the unit, or if it seems to function incorrectly.
Disconnect the power source immediately, and consult your dealer.
LEGAL NOTICE
Supercircuits products are designed to meet safety and performance standards with the use of specic
Supercircuits authorized accessories. Supercircuits disclaims liability associated with the use of non-Supercircuits
authorized accessories.
The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly
prohibited by law.
Supercircuits makes no representations concerning the legality of certain product applications such as the
making, transmission, or recording of video and/or audio signals of others without their knowledge and/or
consent. We encourage you to check and comply with all applicable local, state, and federal laws and regulations
before engaging in any form of surveillance or any transmission of radio frequencies.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries. Android is a trademark of Google Inc. Use of this trademark is subject to
Google Permissions. Apple, iPhone,iPod touch, and iPad are registered trademarks of Apple Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. Supercircuits, Inc. disclaims any proprietary interest in trademarks and trade names
other than its own.
No part of this document may be reproduced or distributed in any form or by any means without the express written
permission of Supercircuits, Inc.
© 2010, 2011 Supercircuits, Inc. All rights reserved.
11000 N. Mopac Expressway, Building 300, Austin, TX 78759
Sales/Support: 1.800.335.9777 | Fax: [phone]

1
4-Camera H.264 Security System Setup Guide
Table of Contents
SECTION1 SystemsOverview...................................................................2
1.1 Aboutthisdocument.................................................................2
SECTION2 GettingStarted:UnpackingtheEquipment.............................................3
SECTION3 InstallingYourSystem...............................................................5
3.1 Camerainstallation ..................................................................5
3.1.1 Cameraplacement...............................................................5
3.1.2 Mounting ......................................................................6
3.2 Install and setup the monitor (SYRF04LCD systems only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3.3 DVRinstallation ....................................................................11
3.3.1 Controlsandconnectors.........................................................12
3.3.2 DVRplacement.................................................................13
3.4 Connecting the system together. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.5 Adjustingthecamera................................................................16
SECTION4 DVRSetup ........................................................................17
4.1 LogintotheDVR ...................................................................17
4.2 Settingsystemtime.................................................................18
4.3 ChangeAdminandUserpasswords....................................................20
4.4 Adjustingthevideoimage ...........................................................22
4.5 Setting up scheduled and automated recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
4.5.1 Setting Motion Detection sensitivity and Mosaic (privacy mask) . . . . . . . . . . . . . . . . . . . . . . .28
SECTION5 NetworkingYourDVR...............................................................34
5.1 Congure the DVR for access on your home network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
5.1.1 Verify local network connectability with IE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
5.2 AccessingyourDVRfromtheInternet..................................................44
SECTION6 KWeyeSmartphoneApp ............................................................48
6.1 InstallingKWeye....................................................................48
6.1.1 InstallingKWeyeiniPhone.....................................................48
6.1.2 InstallingKWeyeinAndroid .....................................................50
6.2 SetupaccesstoaDVR...............................................................50
6.3 UsingKWeye.......................................................................51
SECTION7 Cleaning..........................................................................53
APPENDIXA O-loadedVideoFiles ..............................................................54

2www.supercircuits.com
SECTION 1: SYSTEM OVERVIEW
SECTION 1
Systems Overview
Congratulations on purchasing your 4-Camera H.264 Security System! Your system includes:
• 4–camera networkable digital video recorder (DVR) with a pre-installed 500GB hard drive. The DVR can be congured and
controlled locally, using the operator control panel and mouse or remote control, or across the Internet through the Microsoft®
Internet Explorer® (IE) browse.
The DVR uses state-of-the-art H.264 compression technology to maximize your recording time and optimize your video
quality. H.264 compression saves hard drive space and supports faster data transfer. Data stored in the DVR can easily be o-
loaded via USB or across your network. (See the User Manual for more information.)
• Up to 4 cameras. Features of these cameras depend on the models selected.
• Apple® iPhone®, iPad®, and iPod Touch®, Google Android™, Symbian™, Windows® Mobile, and Blackberry® smartphones apps
that let you monitor your home or business on the go from anywhere
• Supercircuits LCD 17-5 monitor (with SYRF04LCD systems only)
1.1 About this document
This document is a simplied guide to setting up a basic system. For detailed information about your DVR and camera system, refer
to the DVR User Manual.

3
4-Camera H.264 Security System Setup Guide
SECTION 2
Getting Started: Unpacking the Equipment
Your system includes:
• 4 channel H.264 networkable DVR w/ 500GB HD and power adapter (SYRF04-KIT)
• Cameras
• 4 – 60’ video/power extension cables
• Power adapter with 5-way splitter
• User guides for the DVR, cameras, smartphone applications (on CD), and monitor (if included)
• USB mouse
• LCD Monitor (LCD17-5, with SYRF04LCD only, not shown)
• Mini-CD with smart phone applications
• This manual
Remove the equipment from its packaging and place it on a at, clean surface. Inspect each item. If any visible damage is present,
contact your supplier or Supercircuits for a replacement. Verify that your order is complete.
Cameras
5-way
Splitter
Mouse
Remote
Control
Video/Power
Extension Cables
DVR
Power
Adapter
System components shown with CD33-2 dome cameras
SECTION 2: GETTING STARTED: UNPACKING THE EQUIPMENT

4www.supercircuits.com
SECTION 2: GETTING STARTED: UNPACKING THE EQUIPMENT
What you need
Although each security system installation is dierent, most require the following items not included with your system
components:
• Tools to install the cameras and route power and video cables
• Fasteners to attach the cameras to the mounting surfaces
• A display device and cabling to connect to monitor the DVR. The DVR will connect directly to a VGA video monitor, or to a TV
with a BNC to RCA adapter and RCA cable. The display device is usually needed only for system setup. It can be disconnected
when the DVR is networked for access across a LAN or Internet.
• Uninterruptible power supply (UPS). This device is used to ensure system stability during voltage surges, sags, and outages. If a
UPS is not available, a power strip with strong surge protection is highly recommended.

5
4-Camera H.264 Security System Setup Guide
SECTION 3: INSTALLING YOUR SYSTEM
SECTION 3
Installing Your System
This section includes an installation procedure for the CD33-2 dome camera. If you purchased a system with other camera models,
use the documentation included with those cameras for installation setup.
3.1 Camera installation
Your CD33-2 camera is a precision instrument that will provide years of quality service when used properly. Included with each
camera is a 60’ video and power cable.
Drop Cable
Video 75 Ohm
12 V DC
Base
Housing Bezel
Turret Style
Camera Housing
Camera Lens
IR LEDs
3.1.1 Camera placement
Plan your camera installation carefully. Identify the locations where cameras will provide the best coverage, considering:
• Field of view – Cameras must be positioned so they can eectively view the entire area that must be monitored, and in a
location that makes tampering with it dicult.
• Lighting – Direct sunlight shining on the camera lens or bright reections from shiny objects in the eld of view can diminish
video quality and camera performance. Mount the camera in shaded areas, if possible, or where these inuences can be
minimized.
• Ease of installation – Must be able to install the camera at the location, considering mounting hardware requirements,
temperature, dust, moisture, etc.

6www.supercircuits.com
SECTION 3: INSTALLING YOUR SYSTEM
About weatherproof cameras
Weatherproof cameras can be mounted in any open area, such as on a telephone pole or on the side of a building. However, for best
results, we recommend you mount your cameras in a sheltered area, such as under the eave or roof of a building. Point the camera
in the direction you wish to observe. When routing cable near the camera, allow enough slack to form a U-shaped “drip loop” if it is
exposed to moisture or rain water. A drip loop helps to direct water, that accumulates on the cable, away from the camera.
Drip Loop
Drop
Cable
NOTE Cable connections are not weatherproof.
Video/power cables can be run almost anywhere, and are frequently routed through attics or above drop/acoustic ceilings because
of the ease of installation. For added security, we recommend you run your cables in areas with limited access to prevent tampering.
Avoid running the cable near high voltage appliances such as uorescent lighting. Electrical noise and magnetic elds produced by
these devices may aect video signal quality.
A 60’ video/power cable is shipped with every camera in your system. 100’ and custom-length cables are also available from
Supercircuits.
3.1.2 Mounting
1. Separate the base from the rest of the camera assembly by unscrewing the housing bezel.

7
4-Camera H.264 Security System Setup Guide
SECTION 3: INSTALLING YOUR SYSTEM
Removal of housing bezel
2. Determine where the camera will be mounted.
3. Using the base as a template, mark the location of the four mounting screw holes.
Mounting Screw Hole
Camera base

8www.supercircuits.com
SECTION 3: INSTALLING YOUR SYSTEM
4. Drill mounting screw holes into the mounting surface.
a. If the mounting surface is a soft material, such as a drywall, use a 3/16” bit to drill the mounting holes. Use a hammer to
tap the wall inserts provided into each hole until they are ush with the surface.
OR
b. If the mounting surface is a very soft material, such as ceiling tile, place a wood block behind the tile. Screws longer than
1” may be required. Drill holes for the mounting screws through the surface and into the wood block.
OR
c. If mounting the camera on a harder surface, such as wood, drill the mounting screw holes with a 3/32” bit.
5. Determine the cable routing. If the cable is to be routed through a hole in the mounting location within the coverage of the
base, perform the following steps. If the cable will be routed through a cable guide in the base, skip to step 9.
Cable Guide in Base
6. Drill a 3/4” hole through the mounting surface at the center of the base.
7. Use a #2 Phillips screwdriver to mount the base with the provided screws.
8. With the camera in the camera housing, route the drop cable through the 3/4” hole until the camera housing is tted onto the
base. Place the housing bezel over the camera housing and screw it onto the base until the camera and camera housing are
held in place. Skip to step 12.
9. Set the camera on the base with the camera cable pressed into one of the cable guides of the base. Allow some slack in the
cable within the base to allow for camera positioning later.
10. Use a #2 Phillips screwdriver to mount the base with the provided screws.

9
4-Camera H.264 Security System Setup Guide
SECTION 3: INSTALLING YOUR SYSTEM
Tighten housing bezel
11. Without allowing the camera to hang by the drop cable, place the camera housing with the housing bezel over the camera and
t it onto the base. Screw the housing bezel onto the base until the camera and camera housing are held in place.
12. Attach the BNC video/power cable to the camera cable as required.
CAUTION
Notice that power connectors on the BNC video/power cable are dierent at each end!
Extension
Cable
Camera
Drop Cable
Power
Video
Lock Ring
Cable attachment

10 www.supercircuits.com
SECTION 3: INSTALLING YOUR SYSTEM
3.2 Install and setup the monitor (SYRF04LCD systems only)
The SYRF04LCD system includes the LCD17-5 monitor. If you did not purchase this monitor, setup your system monitor at this time,
then continue at subsection 3.3.
1. Find the monitor assembly and base. Use the screw provided to attach the base to the monitor support bracket. The screw may
be attached to the underside of the monitor support bracket or in the base.
Base
Support
Bracket
Screw
2. Attach the VGA cable provided with the monitor to the VGA input connector on the lower back side of the monitor.
Inputs on the lower back side of monitor
3. Attach the other end of the VGA cable to the Main OUT (VGA) connector on the back of the DVR.
4. Attach the power cable to the monitor and plug it into a grounded power outlet.
5. Press the Power button to power on the monitor. The Power button is located in the control panel on the right side of the
monitor.

11
4-Camera H.264 Security System Setup Guide
SECTION 3: INSTALLING YOUR SYSTEM
SOURCE
Move up in menu
Move down in menu
Move right in menu
or volume up
Move left in menu
or volume down
MENU (open/close)
Power
Audio output
Monitor control panel
6. Press the SOURCE button on the monitor control panel to open the video source menu. Use the pand qbuttons on the
control panel to highlight PC, and then press the MENU button to select that interface. An indication will appear on the screen
conrming your selection.
7. Power o the monitor using the Power button on the control panel.
3.3 DVR installation
Your DVR is an advanced network video recorder that includes many features not covered in this guide. Please refer to the DVR User
Manual for additional information.

12 www.supercircuits.com
SECTION 3: INSTALLING YOUR SYSTEM
3.3.1 Controls and connectors
DVR Front Panel
Single/Multi Camera
Display Toggle
tqpu Menu
Navigation
Buttons
Enter
Escape
Menu
Play/Pause
Record
CH1 .. CH4
Camera Select
Infrared
Sensor
Pan/Tilt/Zoom
Control
Backup
Button Usage
o/ Toggles between single camera, multi-camera display.
CH1 .. CH4 Used to select the camera on channel 1, 2, 3, or 4.
Enter Press to conrm a menu choice.
Infrared Sensor Sensor for the remote control.
MENU Opens the main menu window
ESC Press to exit any active window.
REC Use to start and stop manual recording.
BACKUP Opens a video search and playback menu.
u/II When a recorded le is selected, press this button to play. then press it again to pause playback.
PTZ Used for pan/tilt/zoom control of cameras with this feature.
tqpuUse these buttons to navigate through the menu system. Generally, use the tubuttons to move to
selection boxes, and use the qpto select submenu parameters.

13
4-Camera H.264 Security System Setup Guide
SECTION 3: INSTALLING YOUR SYSTEM
DVR Backpanel
IN1 - IN4
Audio In
CH1 - CH4
Video In
Audio Out LANMain Out
(BNC)
Power
Alarm In/Out,
RS422/RS485
Connections
Main Out
(VGA)
USB Power DC 12V
Connector Usage
USB - MOUSE Use these USB ports to connect a mouse, or a backup device such as a ash drive or DVD recorder.
AUDIO OUT Audio output from channel AUDIO IN channels 1, 2, 3, or 4.
IN1 .. IN4 AUDIO IN RCA audio input to audio channels 1, 2, 3, and 4.
CH1 .. CH4 VIDEO IN BNC video input to video channels 1, 2, 3, and 4.
MAIN OUT BNC composite video output to display device (75Ω, 1V p-p).
MAIN OUT VGA Standard VGA output to a display device, such as a computer monitor.
LAN Standard RJ45 Ethernet 10BaseT, 100BaseT port with auto detect.
ALARM IN, ALARM OUT,
RS422 RS485
Use these connectors to attach external sensor devices, alarm reporting devices, and devices with an RS422 or RS485 control
interface, such as PTZ cameras. See the DVR Uer Manual for more information.
DC 12V Connect to 12 VDC power adapter.
POWER Power switch to turn the unit on and o.
3.3.2 DVR placement
Your monitoring and recording equipment is central to constant surveillance and the reliable capture of video evidence. Supercircuits
strongly suggests that it be installed in a secure location with access limited to authorized personnel.
DVRs generate heat and should be placed in a ventilated area. A high temperature environment will reduce the life span and
reliability of the equipment. Additionally, the DVR is not weatherproof, so avoid exposure to liquids and excessive dust. Do not place
objects along the sides or behind the DVR that will block airow through the unit.

14 www.supercircuits.com 14
Uninterruptible power supplies
It is strongly suggested that power to the system be routed through an uninterruptible power supply (UPS). These devices will keep
your security system running through most power outages, in addition to providing excellent surge and sag protection. The UPS
should support your video recorder and all cameras to ensure normal operation during abnormal power conditions.
3.4 Connecting the system together
All connections to the DVR are made on the back of the unit.
Video/Power
Extension Cables
VGA Cable
5-Way
Power
Splitter To 120 VAC
Monitor Power
Power Adapter
Mouse
Camera
Drop Cable
To UPS/
120 VAC
Typical Interconnection Diagram*
SECTION 3: INSTALLING YOUR SYSTEM

15
4-Camera H.264 Security System Setup Guide
SECTION 3: INSTALLING YOUR SYSTEM
15
* NOTE: Power cabling shown in the previous diagram is recommended for systems with CD33-2 cameras. If you are not installing
CD33-2 cameras, power requirements for your cameras may be dierent. Refer to the documentation provided with your camera for
specic recommendations.
1. Connect the system mouse to the USB connector labeled MOUSE.
2. Connect the camera video signal cables (BNC connectors) to the VIDEO IN CH1 to CH4 connectors
3. Connect a display device to the DVR. If using a VGA monitor for a display, connect it to the VGA MAIN OUT connector. If using
the BNC MAIN OUT connector to drive a display such as a TV, attach the appropriate cables between the BNC MAIN OUT and
your display device.
4. Connect the 5-way power splitter to the power adapter, then:
a. Connect the lead marked DVR POWER to the DC 12V connector on the DVR backpanel. Ensure that the POWER switch
on the DVR is o.
b. Connect the other leads of the splitter to the mating connectors on the video/power extension cables routed to the
cameras.
5. Connect the power cord to the power adapter and plug it into a standard grounded 120 VAC power source through a UPS or
surge protector.
6. Power on your system monitor.
7. Power on the DVR using the POWER switch on the backpanel. A startup “Loading” screen will appear on the display. After a
few seconds, the screen will change to the camera view screen.
..
Note: The images you see from your cameras may be dierent from those shown here.

16 www.supercircuits.com
SECTION 3: INSTALLING YOUR SYSTEM
16
3.5 Adjusting the camera
Adjust your camera to produce the best performance:
• While observing video from your camera, use the documentation provided to aim the camera at the surveillance target.
• Depending on the features of your cameras, other adjustments, such as focus, zoom, aperture, IR level, etc. may also be
available. Make these adjustments under various lighting conditions, if necessary, to yield the best video image overall.

17
4-Camera H.264 Security System Setup Guide
SECTION 4: DVR SETUP
17
SECTION 4
DVR Setup
Setting up your DVR includes setting the clock, setting administrator and user account passwords, and setting up scheduled and
automated motion recording.
4.1 Login to the DVR
Initially, two access accounts are provided in your system: Admin and User. With the Admin login, you can make conguration
changes to the system, create user accounts and passwords, and control the privileges assigned to each account. With the factory
default User account login you cannot make conguration changes or create accounts, but can change your own password. The
factory default Admin and User account passwords are:
Admin: 888888
User: 666666
To log into the system:
1. Power on the DVR and wait until it advances to the camera view screen. A typical camera view screen is shown below.
Status
Bar
Image from
Channel 1
Camera
2. Right-click the mouse anywhere on the screen except for on the Status bar. An Input Password window will appear.

18 www.supercircuits.com
SECTION 4: DVR SETUP
18
3. Click the tor uicons next to the Admin box to display the account you want to log into. To make conguration changes to
the system, you must login to the Admin account.
4. Using the mouse, click the number buttons to enter the account password. For example, to enter the default Admin password,
888888, click the “8” button six times.
5. Click OK.
4.2 Setting system time
All recorded data is time stamped using the DVR system clock. Therefore, an exact system clock is essential for recording data that
may be used as evidence of a crime. To check and set the system clock:
1. Power on the DVR and wait until it completes initialization.
2. When the camera view screen appears, login to the DVR Admin account.
3. Compare the DVR system date and time shown on the Status Bar with an accurate clock.
System Date and Time
Status Bar
Note: To see an accurate clock, access a reliable Internet time server, such as tf.nist.gov
4. Right-click the mouse anywhere on the screen except on the Status bar. The Status bar will change to a Tools Bar.